Ford Ranger / B-Series :: 2003 - Misfire And Rough Running / Flashing CEL
Apr 28, 2014
2003 Ranger FX4 Flareside
4.0
Automatic
145,000 Miles
Here's my issue: My Ranger has been running like a dream until yesterday.
I took off on a parts run for my sons Ranger. I got to a stop sign and as I stopped, it started missing and barely running. I nursed it back home and checked the flashing CEL. It was giving me a misfire on #3.
Since I had been planning on changing the plugs and wires, I dove in and got it done hoping that was the cause of the misfire.
Started it up, same thing. I went to the next obvious item: coil. Replace it, still running like crap. Gave up for the night.
Today, I thought I would dig in using the tips here on the forum. Did the spray down...no errant spark anywhere. Tested fuel pressure: 65psi no drop in pressure on acceleration.
Started pulling wires off the coil one by one. Four of the wires resulted in running worse. 2 had no effect. #3 and #6. The coil was producing plenty of spark on all 6 ports.
At this point I was sure it had to be 2 bad injectors. Since I couldn't get injectors tonight, I moved them around after cleaning them a bit and tried my wire test again. The problem stayed on the back 2 cylinders!?!
I tested for voltage on the back injector plugs and I am getting voltage. I also used a stethoscope to listen to all of the injectors. The back 2 seem to remain silent. I have also unhooked the battery for 20 minutes to reset the PCM. Still missing and running rough....
Here's a list of what I have done:
Autolite Double Platinum APP5144 plugs. .062 gap
Autolite Pro Series wires #97051
BDW E97P Coil
New air filter
What should I do next? I really don't know where to go next.......
View 8 Replies
Advertisement
I have a 2003 ranger and have had ongoing problems with misfire cylinder six and have had three different mechanics diagnose the problem as a bad ground. I have replaced all plugs, wires, coil pack, injectors and am constantly pulling the plug on cylinder six, cleaning and often replacing, I also disconnect the battery so it resets the check engine light and it runs fine for about 100 miles and starts running rough again and on goes the check engine light. I have 134000 miles and have maintained it since new.....
View 4 Replies
2000 4.2....Last year I had to replace the coil pack when it started running rough and had a code for a misfire on cylinder 3. It is doing the exact same thing now, same code, same cylinder. Is there something wrong that is causing this?
View 5 Replies
Been awhile since I've been able to post but I've got a serious issue with my 2006 Ranger XLT 4L V6. So last night about 2 miles from home my check engine light started flashing like it was a at a rave and my engine wasn't acting right, also had the STRONG odor of raw gas, no other lights from the dash, no fluids leaking, oil was good n nothing in radiator but coolant. Was able to baby it to my current home but all my tools are in storage so had to wait to get my ODB scanner to see what's up. Scan came back as 'cylinder #3 misfire' & 'O2 sensor reading rich'.
Go cylinder #3 spark plug out and it were fouled bad. Got ride to the store and got a whole new set. Got back n got'em changed and fired ut up, idle still rough and check engine started flashing again and white cloud coming from exhaust pipe and STRONG odor of gas. Check and now have 'multiple missfire', 'cylinder #2 misfire' and 'cylinder #3 misfire'.
Shut it down go and double check ALL spark plug wires are connected and TRY to start, get about a turn n a half then starter spin. Try again and the engine won't even turn over. "Great I've seized the engine!" Was able to put a socket on the crankshaft pully and manually turn the engine over "whew didn't seize the engine", did this a couple of times and tried to start, was rough but eventually it fired up, still idling rough and again check engine light flashing, while it was running I pulled one plug wire at a time from the coilpack to see/feel the lighting and there was spark for the 3 I pulled, didn't affect engine idle.
Run codes and 'cylinder #3 misfire', so now that the engine is was warmed up I pulled out my ohm meter and started checking wire resistance. Cylinders #1, #2 were at .012, #3 was .011 and #5 was .009.
I've figured that the raw gas is due to cylinder #3 not burning and just pushing gas into the exhaust. So to the brass tacks, do I invest in a new set of wires? Or could it be the injector being stuck open and just flooding the cylinder? No when I originally pulled the #3 plug fuel did not spill out. Haven't pulled #3 again due to it being May in Arizona and had to take a break. I'm going on the assumption that the engine wouldn't start after a short run do to "hydraulic lock in cylinder #3", my manually turning the engine over cleared this and allowed the engine to start.
View 9 Replies
I have a 1995 ford ranger 2.3 L dual coil packs new plugs, wires, coil packs, tps, idle air sensor, internal temp sensor, and a replaced mass air flow sensor from wrecker. That all said my one son missed a plug when i replaced it , it had no tip left on it , but since then i now have a misfire in cylinder 2 where the olther plug was found and replaced ...
Gap for plugs are .44
Used the wrecker maf to see if it would clear a p0113 which it did. I am stumped on why at approx. 30 minutes of driving that the cel will flash then set a p0302, no other codes no fuel smell. rechecked plugs all are clean haven't been able to check fuel pressure yet, and i out a can of seafoam in the tank to see if it clear out injectors.
Besides all, I will check injector to see if I hear anything but I'm stumped. Also we have to have an emission test so is it best to fail the test and will it show me what I'm missing.
View 14 Replies
My pops has a 86 ranger with a 2.9. And what its been doing is, it will start up just fine then u give it a minute and itll start to run very rough like a bad miss fire, then if he revs it up for a bit. It will clear out and then run just fine until he starts it up again and it seems to do it more the colder it gets and it smells very rich. Iv checked the injectors and there fine, what other things could it be ? O2 sensors oorrr
View 5 Replies
I have a 2002 ford ranger xlt 3.0 i just rebuilt the entire motor about a month ago and was having a high idle problem for the longest time. turns out i had the iac on backwards. but now that it idles down around where its supposed to it has a rough idle has a little shake to it. starts up right away but when i drive down the road around 3000-3500 rpms its missing on cylinder #3 from what the code I am getting "multiple cylinder misfire, #3 cylinder misfire" I've replaced plugs and wires. camshaft pos sensor. I am getting 65 lbs of fuel pressure. spark on all cylinders. I am really at a dead end here. Also every time I take the plugs out to look at them they look brand new.
View 14 Replies
So I have a 2001 ranger 2.3l . Runs very rough at idle.code says misfire in cyl.#1. I have changed plugs, wires, coil packs all motocraft. I did a compression test..
#1.170
#2 180
#3. 185
#4 . 180
Compression seems fine,but where do i go from here? Anything else i can check/replace to solve this?
View 14 Replies
I have a 03 ranger with a v6/auto trans. it drives fine around town. after i get on the freeway the overdrive light will start flashing. when i get off the freeway it will shift extremely rough. if i turn the truck off and right back on it will be fine again. What could be the problem?
View 5 Replies
I have a 98 ranger with 2.5 and 225k mostly trouble free miles. This engine has never used a drop of oil and ran good. In Dec 3 miles from work started running poorly and sounded to knock the more I asked for power. The CEL started flashing I made it to work and it idled rough but more rpms smoothed out. Took it to mechanic says he did a compression check with little or no compression on #1 & #2. #3 & #4 fine must have broke rings. Doesn't seem right to lose 2 cylinders at the same time out of the blue. Could anything else be causing these symptoms or time for a heart transplant? He hasn't opened anything up yet.
View 6 Replies
My 3.0 with 216k miles has developed a rough idle and it progressively got better with new parts and cleanings. On startup it revs up to 2k then back down to 600. If I let it idle for about 8 or so minutes my Check Engine Light starts flashing. If I drive about for a little bit it stops and is just fine.
While the light is flashing I get codes P1000, P0305, P0306, and P0316. Which are OBDII Monitor Testing Not Complete, Misfire detected in Cyl 5, Misfire detected in Cyl 6 and Engine Misfire Detected on Startup (First 1000 Revolutions) respectively. Any other time the truck runs like a dream. Gets 20 city and 29.5 highway.
I cleaned my Mass Air Flow, replaced my Idle Air Control, SeaFoamed throttle body and vacuum lines, brand new coil pack, new wires, new plugs, new fuel filter, I've only ever run 91 octane, Chevron with Techron goes in at every oil change and B12 every other and I just ran 3 bottles of Lucas fuel injector cleaner.
View 12 Replies
I have a 2006 Ranger XLT 3.0 that is vibrating hard/rough idling, cel is on (solid, not flashing), has trouble accelerating with pedal punched. Will sometimes get a sudden burst when pedal is punched with rpms going up but most of the time no to slow raise of rpms with pedal engaged. Hooked code reader up to it and read ignition coil. Replaced the coil and changed plugs and wires. Truck still not running right. what gives? Is this a fuel pump, cats clogged, cylinder issue?
View 4 Replies
Steam out the tail pipe, misfire codes, rough idle. No water in oil, no over heating. Head gasket ??
View 3 Replies
I bought this from my brother in better than mint condition. Always maintained. Its generating a cyl #2 misfire code.
It starts and runs like new when cold, but when it warms up, it idles rough, and generates the code. after 1500 rpm it smooths right out and runs fine.
He had it to the dealer just before I bought it and they told him needed a new engine.
I am thinking bad injector, since what seems to be happening is, when cold it gets more fuel, or when u rev it gets more fuel, but at an idle and warm, it doesn't seem to be getting enough maybe. And I see from the maintenance records, a couple of other injectors have been replaced as well.
I think the dealer got tired of replacing injectors under warranty and tried to milk him for a new engine.
2002 ranger extended cab 2wd, 3 door, 232,000 kms 5 speed 3 liter V6, new glass and clutch..
View 4 Replies
Engine runs rough at idle. Two plugs are black and just replaced head gaskets. I installed new short block and new heads six months ago. I can't seem to figure out the problem and I would like to trouble shoot more before tearing heads off and going any further.
View 2 Replies
Although my lil' truck (2006 Ranger XLT, 2WD,with 4-cyl / 5spd, and 115K miles) has been running just fine since I bought it about a year & 5K miles ago, I suspected it still had its original spark plugs and I figured I should change them before problems arrived.
As I suspected, the plugs that I took out looked to be original. I measured their gap and they all had excessive plug gaps - around 0.052" gap. I installed the four new AUTOLITE APP104 (double platinum) and checked their gap, and they were a bit tight at 0.042". My book says they should be at 0.044" gap. But I installed them at 0.042 anyway, figuring they'll burn wider in time.
One by one, I smeared a small bit of never-seize on the plug threads & at the plug-to-cyl head tapered edge. I smeared a dab of Dielectric Grease around at the top of the plug to ease the plug wire re-install and hopefully calm any possible arching. The plug wires came off the plugs easy enough and went back on just as easy.
I hit the key and the engine fired right up. It idled rough as expected. However, it continued to idle rough and if I raised the RPM level, it would respond, but still ran rough. It is throwing a 'Check Engine Light' on the dash cluster now - whereas it wasn't prior to the new plugs.
View 8 Replies
My ranger just started running very rough. Like misfiring, but I think it may be the fuel pump. It starts and drives...but it surges then drives normal, as if fuel is being fed, then starved, then force fed etc. My father asked if I had trouble starting it and to be honest in the last 6 months it was a little harder to start on several occasions. On a few occasions it required more cranking. But that was only a few times.
I tried putting in a fuel injector cleaner and 93 octane gas but it is still running even rougher now. I changed out the fuel filter under the rail about a year ago (maybe 8000 miles ago at most). My father thinks the fuel pump is shot and he laughed because his went on his expedition and he said it is inside the fuel tank and there is no way to get at it without dropping the tank. Is that true? 2002 ranger xl 4cyl
View 7 Replies
I live in Kansas and was home in Georgia for the last 2 weeks. The truck drove great there after a fuel up started missing and surging at 50 to 70 thought it might have been bad fuel. waited till it was low added Lucas fuel treatment and premium gas still was doing it. no check engine light. went to Advance and fuse for light was blown they checked and was getting mass air flow code. unplugged it and seemed to be better, not perfect but better. plugged it back in and went to do it again. Changed mass air flow night before the drive back to Kansas. Ran well from Savannah to north Georgia then started doing it again the rest of the way home. Going to have advance check code again.
View 12 Replies
1998 Ranger 4x4 4.0 Ltr - Runs rough ever now and then and CEL giving P1151 code. Upper and lower intake gaskets have been replaced.
View 14 Replies
]I recently bought a 1990 ford ranger with a 2.9 @187,000 miles. That being said I went through and changed a few vacuum lines, the oil, air filter, pcv/grommet, and fuel filter.
The problem is it hates to start. I could crank on it for 10 seconds and not a single thing. Sometimes if i turn the key to the off position, wait a second, and try again, Ill get the truck to fire. When it does fire up it just reeks of the lean exhaust. It also gives me some hesitation when I rev it. I did a fuel pressure test (KOEO) last night and it gave me 32 psi and within a minute the needle fell to about 25 psi. I hear the fuel pump run for only 2-3 seconds too.
I've already pulled the MAF off and cleaned it, replaced the TPS, and did a fuel pressure test. The fuel filter is brand new
View 14 Replies
I have a recently purchased 2000 ford ranger 4X4 with approx. 130,000 miles on a 3.0L. When I bought the truck, it was running rough while in gear at idle, after first putting it in gear, and when coming to stops, then it quit running all together. I started by replacing plugs, wires, and ignition module. I finally got it to fire up after that, but instantly noticed the tell tale white smoke from the exhaust. Needless to say, my oil looked like chocolate milk. Rather than having the heads machined and checked, I opted to purchase a new set of cylinder heads from Dover cylinder head.
I got those on this week and she fired right up. After a few oil changes to eliminate the residual coolant from the oil passages, she still starts and runs fine, although the idle is a bit rough while in park. When I place it in gear the idle gets a little rougher. After a quick trip down the road, I'm noticing a pretty solid shudder when coming to a stop, almost like it's stuck in 2nd gear, but I can't really tell for sure. Seems to shift fine going up through the gears, but coming down is when the issue is.
I believe I'm dealing with two separate issues, one being the rough idle upon startup that doesn't seem to go away, and two being the rougher idle upon stopping. I've read everything from EGR valve, idle air control valve, low fuel pressure, and a laundry list of other things, and I just don't want to start throwing money away chasing my tail.
View 4 Replies
