Ford Ranger / B-Series :: 2003 - Long Start - Cranks For 15 Seconds Before It Fires
Mar 26, 2013
So it often just cranks for 15 seconds before it fires. I put the fuel pressure guage on it and you turn the key on but don't engage the starter it goes to 30 psi then back to 0 in a 2 second time frame. It then stays at zero. when you engage the starter pressure slowly goes up and it starts running while running its a consistent 60 psi.
I presume its the fuel regulator but why does it not go up to 60 psi and why does it just stop with the KOEO? Is it reasonable to just replace the regulator? or should I be replacing the fuel pump to at the same time? I will be doing this from under the truck since there is a lot of hard mounted equipment in the bed.
View 4 Replies
Advertisement
i just rebuilt the motor in my 2002 ford ranger 3.0 and it wont start it cranks over but back fires and bucks alot. took the plugs out and it gets spark and fuel. when it sparks it sparks like multiple times.
View 3 Replies
Alright I thought changing a fuel filter was fool proof but I changed the fuel filter in my 2001 escape v6. awd and now for some reason it wont start right up like it used too before the filter change. It cranks for a few seconds then fires up and runs perfectly fine it sits for a few hours same issue where as before the filter change it fired up fine every time, what did I do wrong. 2001 ford escape...
View 1 Replies
I have the notorious PO171 and PO174 codes on my 2003 5.4L that come back whenever I erase them. I cannot figure out the problem. Whenever I start the truck it cranks for 3-4 seconds before it finally fires, then rpm's are very low, then they finally pick up. I have noticed a loss in power as well. I have completed a full tune-up (spark plugs, coils, boots, filters, etc.)
I have checked the vacuum and PCV lines numerous times, I have yet to find a leak. MAF appears clean. I am running a K&N CAI setup. O2 sensors a good, replaced the gas cap. The only other problem I can see is a bad PCV valve? I hope it isn't a manifold gasket. The truck has been very well maintained and still looks brand-new throughout at 250,000 miles.
View 4 Replies
I have a 2003 Ranger 4x4 with the 5speed automatic. It has 215,000 miles on it and I don't drive it regularly anymore. Lately, I've noticed that it will shake after start up for 10-30 seconds. This only happens after it has sit for a few days or a week. After it warms up, I can drive it and stop and start it again and it has works as usual.
Is there some way the convertor is leaking out fluid and it shakes until the convertor is full again? Or is something else the problem. I've changed the fluid two or three times during the life of the vehicle.
View 4 Replies
This applies to a 2001 F-350 with 73,000 miles on the engine. Engine oil level is good, batteries charged, HPOP reservoir is full and passes Cody test with flying colors. Fuel pump runs for 20 seconds at key on. Start takes about 6 seconds. If I shut the key off and restart immediately it starts in under 2 seconds but if I wait about 30 seconds it's a 6 second start. Here is an AE that I ran on it, it has me stumped. FWIW it seems to start quicker when AE is hooked up. ?? An odd whir type of noise comes out from somewhere under the hood when I first turn the key on and when I clear the codes with AE.
View 14 Replies
Grandson 1991 Ranger 3.0 v6 69,000 miles We have a long start issue after it has sat for 30 mins. plus. If you open the throttle part way while cranking it will start fairly easily. Fuel pressure comes up instantly when you turn on the key. It runs at 39 psi pull the vac line off regulator it jumps to 49 psi. Fuel pressure does drop to about 30 psi after setting an hour. It kinda acts like it is flooded when it starts. so far we have done a complete tune up plugs wires cap and rotor. The ignition module has been replaced twice last one a real Motorcraft. New fuel pump and filter. Cleaned the fuel injectors with Ford cleaning system. I will replace the coil next and maybe clean the iac.
View 14 Replies
I have heard from a few people that it might be the computer that is messed up. Just replaced cap and rotor, spark plugs, wires, fuel filters. Pump turns on. Cranks and cranks but won't start. Took the intake cover off and tried starting it, all it did was back fire. Checked the firing order and everything is right. So im left with guessing at the computer and ignition??
View 5 Replies
Ok, went out last night to go over to a buddies place to watch some football. Tried to start my truck but all that happened is that it would turn over, but not start. Had plenty of juice in the battery, and 1/2 tank of gas. It acted like it wanted to start, but nothing doing - just keeps cranking and cranking. Its even more frustrating because I was driving it around most of the day before this happened.
Here's the dillema: Its been doing this for the past two months now on and off. Once I fix something, it runs for about a month, and then it starts doing this again, without any warning signs (i.e. multiple cranks before a start, stalling, hesitation on accel., etc.). At this point I'm clueless. I've replaced the fuel filter, fuel pump, and air filter, but the problem has resurfaced again.
An interesting thing to note is that the only ways I'm able to get it started when it starts doing this is to remove the electrical connection from the intertia switch, and crank the engine a few times to relieve the fuel system pressure. After reconnecting the inertia switch, the truck starts instantly.
So whats the deal? Why this would work, and why suddenly the thing would not start after weeks and weeks of driving flawlessly? Is it possible that my system is either too pressurized or losing pressure somehow, and that is how it be able to start? A buddy suggested it might be injectors, but I'm not so sure, because there is no hesitation on accel or performance loss, or even a rough idle.
View 14 Replies
My 1999 Ranger that I bought used has been serving me well. However, two days ago I went to visit a friend and when I tried to start the truck to go home, the engine cranked but would not fire. I assumed that perhaps I had flooded the engine, so I walked home. I went back an hour later and the truck started up immediately. Then, yesterday, the truck would not fire at all. I towed it to AutoZone to check for error codes, but none were found. I put my inductive timing light on a plug wire and found that there was no spark.
In one instance of cranking, the timing light blinked and the engine tried to fire, but then nothing. The AutoZone man suggested changing the crankshaft and camshaft sensors. I haven't done that yet, but that is my next plan. Can the Ford dealer find error codes that tell what is preventing an engine from starting that AutoZone can't see? For sure there is no spark, but maybe there is no fuel either since I don't smell gas after much cranking. Could it be the inertia switch cutting off both fuel and spark?
View 14 Replies
My kid is using my 94 Ranger with 215,000 miles. It quit while he was on his way to work. Engine cranks but won't start.
Fuel pressure at rail was 12 psi (Key on eng. off). I replaced fuel pump. Pressure at rail up to 20 psi. Still cranks, no start.
I replaced fuel filter. Pressure at rail up to 30 psi. Still cranks, no start.
Replaced distributor cap/rotor and plugs. I have spark at plugs.
Chiltons from 1994 doesn't list a rail fuel pressure. I see new fuel pressure regulators are set at 41 psi. I pulled mine and hooked air to it. It (FPR) cracks at 37 psi. I have lots of flow returning to tank, so I assume the fuel system is working correctly. I've never replaced the timing chain/sprockets. Distributor rotor spins during engine cranking. When I rotate the crank pulley to 0 Top Dead Center the rotor is pointing to #1 on the distributor, so I don't think the timing chain has skipped a tooth on the sprocket??????
View 4 Replies
2004 3.0L Ranger Edge, 88,000 miles on it, I am the original owner. It won't start. It cranks strongly. Usually when this happens, I have to reset the fuel pump inertia switch. This time, resetting the switch does not work. I disconnected the switch and jumped the two wires going to it, but still no start. The switch seems to work ok, in that I can reset it (a ball, spring, and magnet mechanism, I think), then shake it and the ball will come loose.
The fuel pump 20A fuse in the engine compartment is good. The fuel pump relay in the engine compartment is good (I switched it out with an identical relay that runs the fog lights without problem). I am getting spark. I don't have a fuel pressure gauge but pressing in the Schraeder valve on the fuel rail produces gas.
Usually, when the inertia switch is tripped I can get the engine to briefly start by using starter fluid in the air intake. But not this time. I do not hear the fuel pump kicking in when I turn the ignition key to the "On" position, and that would lead me to think that the pump is bad. Except, I don't get a brief start using starter fluid. The fuel filter has never been changed, but again, since I get no start with starter fluid, I don't see how that could be the problem. OBDII scan shows no codes.
View 7 Replies
working on a 84 ranger it did run fine for 3 wks then while driving there was a thump and it stopped and wouldn't start. Now working on it has spark cranks but won't start. while trying to start when I let off the key it tries to catch but only at that time not when the key is turn to start normal. we poured fuel into the carb and it still didn't start. Leaning toward compression maybe?
View 4 Replies
2007 Ranger 4.0.... Initial start of the day it cranks a bit longer than it should. After warm, it starts fine.
View 1 Replies
Removing fuel injectors-coolant contamination.. How is this done? I need to see if they are any good-or clean/replace them-after I accidentally left the clip off the hose running out of the thermostat housing when I drained my coolant last week and the first time I drove, coolant leaked onto the top of the engine/manifold depressions, getting onto and into the fuel injectors.
I tried to clean it up as much as possible the first time(finally got it going) but still a few days later the truck at times cranks but does not start-hot or cold. I assume my idiocy is the cause or maybe it is just coincidence of something else? From what I read from my symptoms it could also be the fuel pump relay, pressure regulator, coolant temp sensor, crank sensor.. among other things. My fuel pump is 1.5 years old, so hopefully that isnt it. Have the injectors possibly been contaminated to where I should just replace them?
View 14 Replies
SO ive been after this problem for a while now. When my truck has been sitting for 2 days or its a semi cold morning (35 degrees) the truck has a problem not starting. Ive changed the fuel pump, the starter (my starter was going bad anyways and I thought it could also solve the problem I was having), and the battery was just tested. If I leave my key on Acc for like 10 seconds then try to start, it starts right up or if I just re-start right after the first. Now I am leaning towards this being a fuel pressure problem but I am not sure where to start with that... My mechanic also said that it could be the wire that connect to the battery terminal because they can get corroded.
View 4 Replies
Made a trip to the hardware store yesterday. When I came out, the truck would crank just fine, but wouldn't start (98 4.0L 4x4). Tried adding gas, no luck. I had actually called a wrecker, but it eventually started after sitting for about an hour. All I did differently was hit the gas pedal a couple of times. Thinking it may be a low fuel pressure problem, I took it to autozone this morning (started it about 4 times now with no problems). Checked the fuel pressure, and it sat at a solid 65 lbs at idle. I tried holding the throttle open and it stayed at the same pressure. I forgot to try with the vacuum off.
First off, I've seen some people say 60 lbs is right, but more say it should be at about 45lbs. 45 seems right since the fuel return is on the block, not on the pump. I'm guessing the fuel damper went out, but is there any good way to check it? Also, since the damper is vacuum controlled, would a bad vacuum cause this problem? Third, could high fuel pressure cause it to not start? That's the one I'm most worried about what was wrong there.
View 14 Replies
It driving me crazy. Every 10th start of engine it cranks over and over before it fires up, no codes, changed plugs, wires, crank trigger, fuel filter, upper and lower intake gaskets, injectors, iacv. I have no clue. Runs great all time just starting issue every 10th or so start takes 10- 15 seconds to start
View 2 Replies
94 Saab will not start in the mornings , it cranks but wont fire , runs fine later in day with no problems at all . Than next morning a repeat performance of not starting.
View 10 Replies
I am a new owner of my first truck and it is a 2003 Ford Ranger 3.0L Extended Edge with 138,000 miles on it. I keep getting a chirping noise coming from driver side of truck. It only happens when I have the AC on. I can turn AC to just air and the chirping stops. This only happens when I am driving. If I have my truck parked in drive with the hood up, I go and turn on AC full blast and I hear no chirping. I can see AC compressor turn on a few seconds after I start the truck and it is not cycling on or off every few seconds as some people I have asked told me it should do. AC air is ice cold so I should have enough freon. Now this chirping is not constant like a machine gun going off but just about every 5 seconds or so it would chirp. I have heard of bad camshaft sensors causing chirping but would that happen every few seconds and only when you are driving down the road with the AC on? Now I have noticed when truck has sat for a long time I get belt squeal for a few seconds and it then goes away. I think the squeal goes away when AC compressor starts because I observed this when looking for this random chirp. Any clues?
View 4 Replies
My 2006 Azara has had a no start problem since about a year after we bough it new. The condition is intermittent and is not dependent on outside temperature, humidity or other conditions, It happens when the engine is cold or hot. Sometimes the problem goes away for a week or so then it comes back. It happens with either key.
The engine cranks over but does not start. Usually resolve it by sitting for 10 - 15 seconds then trying again. Sometimes have to do this two or three times before it fires. All other electrical items work ok and the battery has no problem powering accessories. I've had it into the dealer however because it is difficult to replicate, they have a hard time repairing the problem. The first time they neutralized the immobilizer and re-programmed it. The second time, I got a check engine light and they replaced the immobilizer. But the problem continues.
View 6 Replies
