I have an 03' Ranger and I assume it has the BW 1354 tcase. I am getting a "clank" sound when the truck shifts from 1st to 2nd. I am thinking its the rear output yoke on the t case. I can grab it and move it up and down but there is no fluid leaking or anything. Would this be a rear bearing problem?
View 2 RepliesJust recently my 2003 3.0 Ranger has started to rev high between shifts. With the clutch in the it will continue to rev high for 8 to 10 seconds. Where should I begin to look to correct this problem?
View 4 RepliesMy '03 Ranger is having a high idle problem. It's a 3.0, manual, 2wd, 141,000 miles. When it's cold it will idle at about 1500 but once I drive it, even just to the end of the block, it will idle at about 3000 and shoot up towards that between shifts. At a traffic light it will idle at 3000 and maybe go down to about 2500. If I bog it down with the clutch it goes right back up once I put the clutch back in or put it in neutral.
I replaced the IAC, no luck. I cleaned the MAF and checked the voltage on the TPS and it is good. I replaced the PVC valve, but the old one was fine anyway. I've sprayed around with carb cleaner and don't notice any difference. I've plugged it into my dad's AutoTap which lets me monitor everything on my laptop and the only thing I can see that looks suspicious is that even with the engine off, the Absolute Throttle Angle reads 18.8%. If I step on the gas with the engine off it goes up to 91.8% so I would imagine that just has to do with the function of the TPS and probably isn't out of the ordinary, but I don't really know what that number means or what the Absolute Throttle Angle is or is supposed to be.
Short of taking the intake plenum off and physically inspecting it for cracks, I'm stumped.
My 03 Ranger 4.0L has become a mystery that has baffled every one I know. Everything was fine and I ran home to something from my house was in there maybe 10 minutes came out and the truck wouldn't start. it doesn't even crank over. out of the clear blue. I had a friend who works for a garage check it and he thinks timing chain. Since then I have been told it wouldn't just fall off sitting there with no indication at all there was a problem.
Thought maybe PATS system. Its in order. Put in on a computer from auto-zone and it shows a check engine light but the reading is there is no codes in the computer on file. I am at a loss. Its been months and I really cant afford to take it to a garage right now. Its the strangest thing ever no crank, no stalling just nothing I hit the switch it lights up like its ready to start and nada.
Where to start looking to resolve this code. It is not an intermittent code. It returns after about 3 to 4 key turns. Truck idles a little rough but runs fine. I have looked up the code and causes but wondering how to deal with this directly and fixed it. I'm wanting to sell my truck for something bigger and would like to solve the issue before hand. 2003 Ford Ranger Edge...
View 4 RepliesMy gf's dad said I could have his 07 Ranger 4.0 2wd with 230K on the clock if I fix the tranny 5R55E. One day he was driving home and all of a sudden had no drive. The tranny will run thru drive, neutral and reverse, but has no drive to it. Engine revs with nothing to show.
Tranny fluid was very dark and pan had nothing but the usual "metal flour" in it. I stopped there, did not pull the filter or anything else.
I have an 03 Ranger 3.0 a/t. A little while back I had a clogged cat, so I took out all the cats and since then it has slowly developed a ticking sound from what sounds like the top of the heads. What that might be?
View 6 RepliesI got this 89 ranger xlt with a 2.9 and automatic transmission. I mainly bought it because it was in such good shape and I was planning on putting a 5.0 in it. everything works on it. the a/c, radio, lights and it runs real nice. the only problem it has is it shifts pretty hard going into second gear. every once in a while it will shift smoothly into second but only like once or twice a day. he said he had recently changed the trans filter and fluid and the fluid does not smell burnt.
View 7 RepliesOk, my question is, when gas pedal is pressed half or more down-ward, a squeal sounding is coming from engine compartment. 2003 ranger v-6 3.0 flex....
View 1 RepliesMy truck jumps or runs roughly... I don't know how to describe it. It's like if someone dumped the clutch. It's a manual, it does it through all gears, so I don't think it's the transmission. I was thinking it might be the fuel pump, but I don't know how to diagnose it. I've got an 83 with the cologne v6. I think it's just got the engine driven fuel pump, no electric, but I'm not sure. Either way, I think it could either be the fuel pump or maybe a vacuum leak.
View 2 RepliesThe first has I replaced my tranny with a stock 4r100 tranny and torque that only has 75k on it. The guy was doing a 6-speed swap. After I had the tranny and torque converter and a new tranny cooler installed, the tranny shifts real hard. I think it may be from my DP Tuner. Even on my economy tune driving it very easy sometimes, it jolts into gear pretty good.
I was wondering if I could just get a shift kit to maybe correct that and if so if I would have to drop the tranny to install the shift kit. I saw a bully dog kit for like 75 bucks, however, I don't really have the money to have the truck in a shop and I would really like to not drop the tranny and not lose all my tranny fluid if possible (very expensive).
Also my other issue, the truck in warm or cold weather is very hard to start. Half of the time it takes two tries to start it. It will crank and crank and no go. Then the second try it fires right up. It has two new batteries, where do I start? Is it possible that the starter is just getting old or is it fuel or oil pressure related possibly?
I am first time ford owner of a 2003 ford f150 super crew fx4 with the 5.4 Triton and lately when I accelerate hard and it down shifts. It shifts excessively hard or when your going slow and the have to accelerate it also shifts really hard i dont know if it is the diff the U-joints or if its the transmission.
View 4 RepliesMy truck rattles when going up hills. The higher the rpm,the more it rattles. It sounds like a heat shield shaking. Also, when I accelearate on a flat road, I hear this very light knocking sound.
Motor has 190 000 km and is due for an oil change. Spark plugs and plug wires have been replaced. Engine sounds good when I rev it. No abnormal sounds. So, what would be my issue? Carbon build up?
1994 FORD RANGER stalls while driving - differant speeds ...differant miles ...no rhyme or reason to it - cranks right back up ...can even pop clutch and cut it back on. Already replaced Ignition Start Module - Dpes sensor - temp sensor - and scan shows all codes are clear and truck passes. We are clueless to whats causing this. 4 cyl 2.1
View 12 RepliesI have a 95 Ranger with the 2.3L and it is a five speed. I am having a starting issue. I have replaced the ignition switch, clutch position switch, starter relay and had the starter tested. The truck will not start with the key. I can jump across the relay and it starts fine but will not even click with the key.
View 3 RepliesI had my battery out for quite some time. When I put in a brand new battery my key was not recognized and my truck will not start.
View 3 RepliesAlthough my lil' truck (2006 Ranger XLT, 2WD,with 4-cyl / 5spd, and 115K miles) has been running just fine since I bought it about a year & 5K miles ago, I suspected it still had its original spark plugs and I figured I should change them before problems arrived.
As I suspected, the plugs that I took out looked to be original. I measured their gap and they all had excessive plug gaps - around 0.052" gap. I installed the four new AUTOLITE APP104 (double platinum) and checked their gap, and they were a bit tight at 0.042". My book says they should be at 0.044" gap. But I installed them at 0.042 anyway, figuring they'll burn wider in time.
One by one, I smeared a small bit of never-seize on the plug threads & at the plug-to-cyl head tapered edge. I smeared a dab of Dielectric Grease around at the top of the plug to ease the plug wire re-install and hopefully calm any possible arching. The plug wires came off the plugs easy enough and went back on just as easy.
I hit the key and the engine fired right up. It idled rough as expected. However, it continued to idle rough and if I raised the RPM level, it would respond, but still ran rough. It is throwing a 'Check Engine Light' on the dash cluster now - whereas it wasn't prior to the new plugs.
Last night I decided to see if I couldn't do something about my leaky carburetor in my 1983 ranger. It's a motorcraft 2150 carb. I took it all apart and followed a guide to clean it, then put it all back together and reinstalled it today. Unfortunately my truck won't idle, makes a whiny noise, and acts odd with the accelerator.
I've got a video posted here : 1983 Ranger Carb troubles - YouTube ....
I tried to explain this to a garage in January with no luck. When it is raining I hit my brakes and my truck jerks like whiplash. Softly hitting brakes doesn't do it, normally hitting them does it (only in the rain), I had some welding done after I went to the garage.... They fixed the front passenger side now it feels like it is under me and it is now doing it when I brake in reverse too... I bought it October 2012 and it was safety inspected until October 2014. Trying to decide if it is worth keeping. I want to keep it but when I go to a garage they see dollar signs. It only acts up when it's raining. And I had the welding done in January and it was fine, until I got new tires last week.
View 12 RepliesOk, I replaced the head gaskets on this truck a couple years back and now I am having symptoms similar to the ones I was having then. I am not entirely convinced that this is what is wrong however.
Symptoms:
Truck was idling rough until it warmed up
Truck takes forever to warm up or simply does not warm up
If/when it warms up it operates at higher than normal temp/almost overheats(it hasn't overheated yet)
Heater blows very cold air
White smoke(has been cold outside so not sure if due to temp or coolant)
Overflow bubbled when I shut the truck off, but it has only happened once so far
I am kind of at a loss, but like I said am suspicious of the head gaskets.
My truck is pulsating when I am coming to a stop, a lot of you all said replace the rotors to which i did and new brakes, shocks. Today I went to get my truck all four wheel alignment done to my truck.. something is not right..
I got my driver tire facing straight, look at the left.. I went back to the alignment shop showed them that, they put it back up there, they called me over and pointed out the machine they use say, it is aligned.. So what is the problem you figure?
To update all I've done to the truck in regards to front end..
rack and pinion
upper control arm
upper lower ball joints
stabilizer inks
rotors (front)
brakes
shocks
When I straighten my left wheel, the right does not look right..