Ford Ranger / B-Series :: 2002 - Shutting Down While Driving
Apr 20, 2012
Our Ranger, 2002, 4 cyl. 2.3 5 speed is shutting down while driving. This has happened twice very recently. Both times on interstate at highway speed. First it loses power then completely shuts down. After stopping, turning key "off" it restarts and runs fine. It does take a longer time to crank before starting.
It is not throwing any codes and the CE is not coming on. I suspect the fuel pump is shutting down. Seems like fuel pressure loss is reason for loss of power? Then extended cranking to restart is the initial build up? What else could it be? If not the pump itself, is there something that would take away power from the pump then get reset?
View 3 Replies
Advertisement
The gas pump/hose keeps shutting off when I fill my tank. The problem is progressively getting worse. No Codes. Truck runs fine. I looked at the filler neck and filler hoses. They appear to be original but no obvious signs of an issue...
View 9 Replies
After starting the car and driving for about 10-15 minutes a few days ago I came to a stop in a parking lot and the car shut off and would not re-start for about 5 minutes. The car started again so I shrugged it off and drove on. About 10 minutes down the road again the oil lamp started to flash and the STOP warning came up. I unfortunately was on a one lane construction zone so I had to limp for a minute to clear it so I could pull over. The car would switch from responding/non-responding to the gas pedal. Finally pulled it off to the side got it towed home and to the mechanic. I haven't heard any news yet but I'm trying to gather some info.
Just a few things I've read about looking into :
-ECT (Engine coolant temperature sensor) ...
-Oil pump ...
View 3 Replies
I just got my grandpa's 2002 Ford Ranger Edge after waiting years to obtain it. It runs great the only problem is that there is NO power to the radio what so ever. The truck belonged to the family and every one drove it but no one knows what happened.. There is no power to Fuse 28 however 12V to all other fuses that have to deal with the radio.
View 12 Replies
I am installing a used tranny in the ranger. According to the salvage yard the tranny fluid and filter was removed and fluid drained from the torque converter. How am I supposed to fill the torque converter?
View 1 Replies
02 Ranger with 3.0 Flex motor, 375K+ miles. Been chasing an issue for a while now, but am about at the end of my diagnosing capabilities. Issue started with a misfire on 5 and rough running engine with no codes showing up. Now the motor is getting worse.
Idle a little rough and no power when accelerating hard. The engine sounds like a popcorn popper under hard acceleration. Motor revs up to 4K but does not pull or shift gears until I let off the gas.
The code that initially showed up indicated a bad Camshaft Position Sensor. Changed that and the Sync assembly - as per instrucions, exactly positioned same as old one. New codes showed up - P1152, P0175, P0171. Cleaned the MAF, rail fuel pressure OK, can't find any vacuum leaks, replaced both upstream ox sensors, and changed #5 ,6 injectors.
Motor still runs the same - like crap, like a corn popper on acceleration, smooths out if only slightly accelerating, but stumbles n bumps on steady cruise speed over/around 60 mph - and no codes showing at present.
I really, really don't want, nor can I afford, to take it to the dealership, but I may be forced to if I can't figure this out sometime quite soon. I make my living with this truck so, no truck, no work till this issue is solved.
View 7 Replies
I have a 02 ranger..3.0 standard trans 4x4.... Started running crappy, cleared up and when shut off, now wont start... Good spark and good gas pressure... Seems to want to try, but just doesn't go. No codes or pending codes.
View 8 Replies
I have a 2002 ford ranger with the 2.3l and 5 speed.
Long story short, previous owner adjusted the time because he accidentally got the motor out of time (he thought it had the belt, not the chain). So he had to take the intake, fuel rails, fan, throttle body, etc. Off to get to the valve cover to re-time it with the timing kit. After it was put back together, it ran awful. I bought it, checked the time with the timing light and it was good. I replaced the spark plugs, and then realized he had forgotten to plug the camshaft positioning sensor back in. So I did, and that did the trick. From start to finish, the truck had those issues for about a year before I got it so it sat up for a little while. I have had it for 2 weeks now.
Now the problem...it idled great. But when I took it out for the test run, 1st gear shifted great, but at about 1700-2000 rpm (depending on the gear), it would almost seem to loose power, and then it would pick back up around 2400-2700 rpm like nothing had happened. You can sort of tell in 2Nd gear, but it is very noticeable in 3rd, 4th, and 5th. If i accelerate pretty slow, it doesn't happen. It only if i try to accelerate at a normal rate or if i am trying to get onto the interstate or pass someone. I ran some seafoam in it thinking maybe it just got gunked up from sitting for so long, but that only through an engine code saying my bank 3 was misfiring.
So I replaced the spark plugs (again), wires, and then the coil pack (the coil pack is what fixed it) and that got the code to go away and for it to stop missing, but the problem still was the same. It would take off great, and then it would seem to almost pause, and then pick power back up again. It wasnt feeling like it isn't getting enough fuel, it just wouldn't hardly pick up speed. It almost feels like I am riding a 2 stroke dirt bike. The power band is ehat should be normal on the truck, and before I hit the power band is how it feels when the truck has its little pausing episode. It's that noticeable to me.
So I thought maybe the fuel filter or sensors need cleaned/replaced..so yesterday I replaced the fuel filter and cleaned every sensor around the top of the engine, including the MAF sensor and made sure all bolts were tight and gaskets were good. I don't see and disconnected vacuum lines and none of them looked dry rotted. The only place air can get in that I see is the air filter box. The screws that hold the top half of the (stock) filter box are missing, so it is not sealed.
But what to check next. My only other thoughts are the catalytic converter (which it doesn't act like it's stopped up) or the fuel pump pressure being off. Also, it does sound like a lifter ticking in the motor, but previous owner said he thinks it did that before all these problems.
Also, right before I bought it, it sounded like the ujoint was squeaking (it rarely does it now) and now it has a crackling sound when accelerating at low-mid rpms coming from the middle or the back of the truck. It sounds similar to when you turn your hot vehicle off and the exhaust makes crackling noises sometimes.
View 2 Replies
1994 FORD RANGER stalls while driving - differant speeds ...differant miles ...no rhyme or reason to it - cranks right back up ...can even pop clutch and cut it back on. Already replaced Ignition Start Module - Dpes sensor - temp sensor - and scan shows all codes are clear and truck passes. We are clueless to whats causing this. 4 cyl 2.1
View 12 Replies
The panel goes off and the fan quits blowing. Sometimes it works, cools great, then just cuts off...
1989 Bronco II 2.9 4x4 auto 164k miles... I have been on TRS, BroncoII Corral, and even FSB searching.
This is the first attempt at reaching out because i have found that here at FTE the folks that chime in know their stuff, or know where i can find out for myself.
View 6 Replies
Today my 2001 ford range edge starting running funny. When in park it idles around 3k rpm and then when driving it feels like it wont shift past 2nd because it is around 4k rpm around 50mph and I'm afraid to go to any higher speed for fear of damaging the engine. I'm currently at work so im unable to really get under the hood atm.
View 2 Replies
Where is is my fuel filter and what are the steps to changing it. I have a 2002 Ford Ranger. Also how do you change the flashers, the left blink is really fast but the right blink is fine.
View 14 Replies
My ranger just started running very rough. Like misfiring, but I think it may be the fuel pump. It starts and drives...but it surges then drives normal, as if fuel is being fed, then starved, then force fed etc. My father asked if I had trouble starting it and to be honest in the last 6 months it was a little harder to start on several occasions. On a few occasions it required more cranking. But that was only a few times.
I tried putting in a fuel injector cleaner and 93 octane gas but it is still running even rougher now. I changed out the fuel filter under the rail about a year ago (maybe 8000 miles ago at most). My father thinks the fuel pump is shot and he laughed because his went on his expedition and he said it is inside the fuel tank and there is no way to get at it without dropping the tank. Is that true? 2002 ranger xl 4cyl
View 7 Replies
Misfire is on #6. Feels like a partial miss, not every revolution, and there's no noticeable miss while cruising or holding a higher rpm in neutral. It's a B3000 with 97k miles. New Motorcraft plugs, new wires, 10.7k ohms across coil terminals (1-5, 2-6, 3-4).
I've swapped plug wires between cylinders and side-to-side on the coil. I also sprayed MAF cleaner all around the intake looking for a leaky gasket. I feel pretty confident I'm looking at a bad/dirty injector or valve issue. I plan on doing a compression test next and hopefully nail it down to one or the other.
I'm asking for input on my diagnosis so far. And how difficult is it to replace the injector? Will I need to remove the upper intake?
View 12 Replies
After about 1 minute after starting the truck it sounds like the fan belt is squealing..(below 30 deg outside) Only its not the fan belt as I replaced it. Does not do it when it is engine is operating temperature. Have checked all of the Pulleys which seem to be all right. The frequency of the squealing sound is about 1/3 the engine RPM and will go away above 2k when it does do it. Stopping at a stop light after about 45 seconds it really starts to get loud. Can a Fan Clutch do this.. I beleive that this engine has a timing chain right?
View 8 Replies
I have a 2002 Ford Ranger 3.0L truck that, all of a sudden, has a problem with the HVAC system that blows air only thru the defrost vents even when selecting any other vent levels (defrost, face/middle or floor levels).
I did find a thread on another forum regarding this problem, only it was for the 95-01 Ranger model years, yet they say that the 2002 Ranger is not the same as those earlier models.
View 8 Replies
Bought a 02 Ranger, 4.0 4x4 super cab 122,000 miles. etc Picked it up for 500 bucks because someone scrapped it along the side of a guardrail this last winter. Replaced rack and Pinion (cracked), Tie rods, Shocks, driver side knuckle and wheel bearing, and some body issues (bed is still shot so if any black short bed sitting around let me know). I've been kind of putting around all day in it, letting it used to working again. Starts right up, turns easily, I string aligned it so it goes where I want.
But as I get up to speed start at about 10MPG there is a vibration based noise coming from the front, can't pin down if its left or right. If Im going straight then turn it gets slightly more intense as I even start turning the steering wheel. The noise increases with vehicle speed. And I don't know if its separate or related, but any turn over 5-10* to the left results in a grinding sound but then I turn to about 10-15 and it gets less intense. No noise turning right.
I'm thinking a bad CV, TWO bad CVs, or a bad differential. Before I start ripping into those things, thought I'd get opinions, or hopefully experience in this area. I'm really hoping its something small and stupid. (like not getting a professional alignment)
View 6 Replies
I removed what I could, plastic cover and thermostat housing. Looks like I have to pull the intake to get the little bugger out of there. What's the procedure to remove and replace?
View 2 Replies
2002 Ranger 2.3 duratec ... My Oil Needle jumps around from center to zero. (I am aware this could be/is a dummy light style). There is a Pressure switch attached to oil filter housing, I thought this was oil pressure sender. The pressure switch I was sold is cylinder with single prong connector. Not matching the sensor on oil filter housing. What sensor is on my oil filter housing? Also where is my oil pressure sender?
View 2 Replies
I have a 2002 Ford Ranger, and it wont start at all. Ive replaced the starter, had the battery checked. Not the battery, took starter out, had it checked too, its not the starter either. Someone said it maybe a fuse? This is totally frustrating, and I need to get it figured and fixed asap. Its been going on for weeks., I had it fixed and then it just stopped. It wont even take a jump anymore.
View 4 Replies
I have a problem with my 2002 Ford Ranger XLT Super Cab's passenger window. It seems like it has a loose connection, but I am not sure what the exact problem is. When I try to move the passenger window from the driver side control panel, nothing happens. The driver side window works fine. On the passenger side control panel, I can hear the motor trying to move the window when I try to put it up (the window is already up).
When I try to put it down, I hear nothing unless I push the button repeatedly - anywhere from 3 to 20 times. When the window is partially down, moving up always works, but I have to keep trying to push the button to make it go down. I have tried pushing down on the window while I press the down button and spraying white lithium grease in the window tracks while the window was down, as well as pulling part of the seal away from the window while I tried to make it go down.
View 5 Replies
