Ford Ranger / B-Series :: 2001 - No Fuel Pressure At Start
Aug 21, 2014
2001 Ranger, 108,000 miles, good regular maintenance per the Ford Schedule. 4.0L manual trans.
I changed the fuel filter 20,000 miles ago. This has been a recurring issue anytime my fuel level was low, about 1/4 tank or less, and when the truck was warmed up, hot. The fix in the past was to add fuel and let the truck sit for awhile. Now, today I drove home for lunch and when I tried to start the truck to return to work, it wouldn't start.
Same conditions, low fuel level and it was warmed up. The engine will turn over and start to run with ether in the air box, so it's definitely fuel related. A fuel pressure gauge on the Schrader valve got a zero reading, not even a flicker, and no residual pressure after shut off.
Could this be only a fuel pressure regulator issue? Or should I prepare to replace the fuel pump? Is there a fuse that might be blown?
View 14 Replies
Advertisement
I have a 95 Ranger 2.3 with a manual tranny. In the past I have had problems with this truck not starting do to a bad inertia switch and numerous fuel pumps. A couple of weeks ago I pulled the truck off of the driveway into the street and let it set there for a few hours. When I went to put it back on the driveway it would not start. I got it pushed on the side of the garage. I did my normal routine of doing a pressure check. I had no fuel pressure so I assumed that it was the fuel pump (as usual) so I dropped the tank and changed the pump.
I got it back together and it still wouldn't start. I checked the fuel pressure and the manifold still had 0. So I started my diagnostic. I have power from the fuse to the fuel pump relay. I then checked the wiring at the inertia switch and found that there is no voltage with the key on at the supply side of the inertia wiring. I verified continuity between power distribution block and the inertia switch. I put in a new fuel pump relay and it still has no fuel rail pressure and there still is no electric signal at the inertia switch. Where to go from here?
View 6 Replies
Sons 94 ranger 4.0 4x4 Auto 185k got him to work yesterday but would not start to bring him home. No spark, checked with timing light, and no fuel pressure. Searched and read alot of tips from Pawpaw so I tried a few things with no luck. Swapped the relays around, inspected coil pack and plugs. CEL was not on and goes out while cranking. I have a OBD scan tool but this truck must be too old or I need finding plug. Crank sensor maybe?
View 7 Replies
Made a trip to the hardware store yesterday. When I came out, the truck would crank just fine, but wouldn't start (98 4.0L 4x4). Tried adding gas, no luck. I had actually called a wrecker, but it eventually started after sitting for about an hour. All I did differently was hit the gas pedal a couple of times. Thinking it may be a low fuel pressure problem, I took it to autozone this morning (started it about 4 times now with no problems). Checked the fuel pressure, and it sat at a solid 65 lbs at idle. I tried holding the throttle open and it stayed at the same pressure. I forgot to try with the vacuum off.
First off, I've seen some people say 60 lbs is right, but more say it should be at about 45lbs. 45 seems right since the fuel return is on the block, not on the pump. I'm guessing the fuel damper went out, but is there any good way to check it? Also, since the damper is vacuum controlled, would a bad vacuum cause this problem? Third, could high fuel pressure cause it to not start? That's the one I'm most worried about what was wrong there.
View 14 Replies
I have a 1990 Ranger with a 4.0L that I just changer the intake gasket on. I broke the fuel line at the Fuel Pressure Regulator. Cant seem to find one anywhere. It is a nylon inside/rubber outside with a cloth mesh and quick connect fitting line. Where to get one? Can I hose clamp it the FPR by cutting off the connector that broke?
View 1 Replies
I've got 30 lbs of fuel pressure that drops to 28 if you rev it up a bit on a 1998 ranger 4.0 with a new fuel filter. Haynes manual say it should be 56-72 lbs. Bad news is fuel pressure regulator is in the tanks with the pump. Can the regulator be swapped out or is it one assembly with the fuel pump? Is there anything I should check first?
View 4 Replies
Ok so my dad has been using my 98 while I was fixing his 92 4.0. I had the 92 perfect and then someone pulled in front of me and totaled it out. Well now I got my 98 back and it's all messed up. Check engine is on p0171. Fuel pressure test done and it's steady 40-42 psi. I remember last year I checked it was like 68-72 psi. It hasn't been a year or two since fuel pump and strainer were replaced. Filter probably 15,000 miles ago. It's currently running good sometimes it cuts off when you start it then next time it stays running. Is this another fuel pump failure? How much longer will it last on 40 psi? The fuel lines and tank have 336,000 miles, engine maybe 150,000 and injectors have about 20,000 miles on them.
View 4 Replies
I am losing residual fuel pressure on my 1996 ranger 2wd, 3.0, V6. Acts fuel starved after sitting for awhile, cranks ok turn key off starts up, sometimes i have to do this twice.
View 7 Replies
I have a 2009 Ranger 2.3 L manual with about 100000 miles. The engine was bogging down and I just found out that the MAF sensor is bad from testing it. In the process, I measured my fuel pressure to be 73 psi (manual says 60-65 psi). So I have two questions:
a.) Is there any chance of just cleaning the MAF sensor. The sensor has zero volts when running and warm (or .02 v) and barely changes when reving the throttle.
b.) Perhaps then the high fuel pressure is an unrelated issue. Is this so high that I must change the regulator as I have to change the pump as well? Might it be some other issue than the regulator which is what the Hayness manual says?
One theory I had for the high fuel pressure is that the bad MAF was leading to bogging and lean conditions and the computer was running the pump more to compensate but I think the computer might run the pump based on fuel pressure not the o2 sensor.
View 7 Replies
I have a 2000 Ranger with the 3.0. Was wondering where the fuel pressure regulator is located on it. I like pictures.
View 1 Replies
I have a 2000 Ranger with the 3.0 in it. Trying to find where the fuel injection pressure damper is located. I was told it's on the fuel rail. Just making sure I'm looking at the right thing.
View 3 Replies
My 94 B4000 (4.0L ohv)is acting weird. If I let it sit for more than a day, it won't start. I pop the intake tube off, squirt some gas in the plenum, and away she goes. It starts all day long after that. I can hear the fuel pump running. Is there a possibility there is a fuel pressure regulator leaking down, kinda like a pump losing it's prime? Or am I looking at dropping the tank for a new fuel pump??? It's getting close to winter up here (gonna snow anytime) and I don't need this kind of trouble when it's cold and snowy.
View 11 Replies
I have a 2002 Ranger with a 3.0/auto with about 180K on it. It runs good but for the past 6 months I have had a problem starting it. It does the same thing hot or cold but is a LITTLE easier when cold. It is very hard to start, you have to grind the started for about 30 seconds then it starts right up.
I checked to see if I could hear the fuel pump when the power is turned on and yes I can. But after checking the fuel pressure, there is no fuel pressure with the power on and the engine not running. Once the engine starts, there is about 65-68 pounds of fuel pressure - and the truck runs just fine. Starting is the only problem.
I was told I had to replace the fuel pump. Is the electric pump in the tank the ONLY fuel pump on the truck, or does it have a combination of the electric/tank pump and a mechanical pump on the engine?
View 7 Replies
I have a 2001 Ranger 4.0, 4x4 that just hit 100k and the oil pressure gauge doesn't show a reading for about 1 minute after startup. Also, the check gauge light comes on. What do I replace to fix this and is it something I can do myself? I am mildly handy. Would you worry about fixing it or just let it go because it's obviously getting oil pressure.
View 2 Replies
Dad has a 2001 well cared for Mazda B3000 with around 128,000 miles on it. Motor runs fine, so did the tranny up until a couple of weeks ago. The tranny needs a new clutch, throw out bearing, and pressure plate. It was drivable up until about four days ago.
My Dad has been working 6-7 days a week and hasn't had time to tear into the tranny. We just drained the old fluid out and put in new when it first started making the noise it makes. We have priced the parts and was just waiting for my Dad to get a weekend off to tackle the problem. But someone at work told my Dad to bleed the slave cylinder before he tore into the tranny, just to see if it would work.
Well we bled the slave cylinder just like you do brakes. But now the clutch has no pressure, it just goes to the floor. We have tried everything. My dad uses the truck to commute back and forth to work. So, I am looking for any tricks on how we can get pressure back in the clutch so he can get to work.
View 14 Replies
Mine has a strange issue. 1990 xlt 2.9L manual 4x4. When first start of the day, after start I push accelerator and it has a hesitation like not getting fuel. Where start?
View 1 Replies
My 1995 ford ranger with a 3.0 will not start. It acted like the fuel pump was going out so I replaced it. I also replaced cmp sensor and the camshaft synchronizer due to old cmp sensor broke and messed up the synchronizer. My truck is getting fuel and spark but still will not start. Where do i go next?
View 4 Replies
My 1999 4.0L v6 Ranger (auto trans) is having some issues. Recently the fuel pump won't turn on as normal when I turn my key. I have to turn the ignition on and off 10-20 times before I hear the pump kick on and I can start it. I already checked the relay and fuel pump shut-off switch. Neither was the bad.
View 10 Replies
I have a 1988 Ranger 2.9 V6 that sits most of the time. The fuel pump quit working so I removed the bed and replaced the pump in the tank and the inline filter near the engine. I did not replace the inline high pressure pump because it still made a humming sound so I assumed it is working. Now when I turn the switch on I hear both pumps working but the truck will not start. It seems like it wants to fire or fires for just a second but just wont completely start. Is the system supposed to be primed and if so how?. I suspect a fuel problem but I dont know how to check pressure or check to see if fuel is getting to the engine. What to do next?
View 6 Replies
My daughter's boyfriend just bought a 2000 ranger with a 2.5. We just put a flexplate in it and it wouldn't start. Just turned over. Listened for the fuel pump and no noise. After a few minutes, it worked. He drove it home last night and said that it didn't want to work first try but worked with the second try. He drove it to church, 40 miles, and it sit for around two hours and wouldn't start, no matter how many tries.
We tried changing the relays around with no luck. We went and eat lunch and back to the truck with a rubber hammer. Then it starts on the second try without using the hammer. We got under it and cleaned the connections up and put some bulb grease on them. I couldn't get the one apart right on top of the pump itself, I was afraid of breaking it. It's been doing fine since we left the church before we cleaned the connections.
View 14 Replies
its 1986 Ranger with a 2.9L V6 Auto 4x4, well to start with it seriously over fueling also it idles very roughly and even stalls out sometimes, when I'm trying to hold it at a speed it acts like it is missing (I guess that's from over fueling as well and it also pukes out lots of black smoke, it goes through way too much gas for a V6), but when I speed up fairly hard it acts fine until I try to maintain speed again, I have already put a tune up into it and a new EGR as well a fuel regulator and how to fix it?
View 14 Replies
