Ford Ranger / B-Series :: 2001 4.0 SOHV Upper Intake Manifold Removal


Feb 24, 2007

It doesn't look anything like the illistration in my Haynes book.Where are the bolts located and how many?

View 14 Replies

Advertisement

Ford Ranger / B-Series :: Polishing And Porting Upper Intake Manifold

So i was thinking about buying a intake manifold for my truck and porting it and polish it. Would it be worth doing. I've decided that trying to port the heads will take up to much time and money for gaskets. Now the only reason why I am buying another stock one is so i can take my time and do it right.

View 14 Replies

Ford Ranger / B-Series :: 1987 V6 - Intake Manifold Removal?

I was working on my friend's '87 Ranger with 2.9 L V6, and a little bit of dirt fell into the intake manifold through the injector ports and intake ports. I should've cleaned the top of the engine with a shop vac first. Anyway, should I remove the intake manifold, or try to vacuum the bits out? It's pretty oily inside, and they might be stuck to the inside of it, so the vac might not do much. If I have to remove it, do I have to de-mesh the distributor gear to remove it, or does the distributor attach to a splined shaft? After looking at the diagrams, the answer was unclear.

View 1 Replies

Ford Ranger / B-Series :: 2003 - Intake Manifold Leaking?

'03 Ranger, 2.3L. Runs great except at idle. Code p0171. Replaced IAC, no luck.

Brake cleaner leak test definitely results in engine rpm change right around "butterfly rod" plug in front of intake manifold near no. 1 cyl. I'm pretty sure that's the problem - the plastic plug blew out. I watched a video showing repair, but it seems lacking.

I do not want to loosen up intake for access - I'd rather remove steering pump and gain some access to plug it up. There still isn't much access but, but eyeballing it, enough to plug, I think.

Three steering pump bolts came out easy. The fourth one is behind fluid line - extremely difficult to access, imo.

Somehow try to remove pump for access to intake hole, or bite the bullet and remove intake manifold for access?

View 6 Replies

Ford Ranger / B-Series :: Antifreeze Leak - Tightening Intake Manifold Fasteners

I am mixed up in which fasteners I have to tighten to stop my antifreeze leak. For this, I got some pictures. Do I have to tighten these bolts? Or these? Is this the upper intake intake manifold?

I am just really lost and want to tighten the right bolts and find the torquing specs of the bolts. In the first picture, we can clearly see there is a leak there of what must be antifreeze. The stuff I have been loosing slowly over months.

View 7 Replies

Ford Ranger / B-Series :: 1996 4.0 - Loud Whistle Intermittently From Intake Manifold Area

Just bought this truck and no check engine light was on, went to get it smogged so I could register it and it had the following fault codes: P1443, P0401, P1131, and P1132. The truck seems to run great in my opinion and even gets really good gas mileage. There is a whistle intermittently from the intake manifold area though that is at times pretty loud.

Smog tech told me these trucks are "notorious" for the check engine light going bad and that usually the entire instrument cluster has to be replaced in order to fix it. I'm a very experienced motorcycle /small engine tech but do not have much experience with car/truck engines and especially not with emissions control systems.

Again it is a 1996 Ford Ranger 4.0 V6, 4 wheel drive STX with 185,000 miles on it. Where to start or what might be the source(s) of these error codes?

View 5 Replies

Ford Ranger / B-Series :: 1994 - Sputtering Started Suddenly - Vacuum Leak Behind The Intake Manifold

I have a 94 ranger and all of a sudden it started sputtering, i can hear a vacuum leak behind the intake manifold found what appears to be a pcv valve not hooked up is that the way it's supposed to be?

View 2 Replies

Ford :: Escape - Coolant Spilled On Upper Intake Manifold / White Smoke On Startup

Coolant spilled on my upper intake manifold. I washed it off to the best of my ability but when i started the car white smoke came from tge exhaust. What my next move should be?

View 3 Replies

Ford Super Duty (1999-2016) :: F250 - Hole At The Back Of Upper Intake Manifold

1999 F-250 LD 5.4... There is a hole on the back of the upper intake manifold, just below the back of the throttle body, is a vacuum hose supposed to be attached here? Have a serious vacuum leak, no coolant loss, no overheating, just had cop's and spark plugs done, now she backfires, stalls and will not stay running, mech. says its an intake gasket but the gasket and lower intake manifold look new.

View 7 Replies

Bonneville :: 1995 Pontiac GM 3.8 Upper Intake Manifold Replacement

Just today,when replacing the UIM on a naturally aspirated 95 Pontiac Bonneville 3.8 with a Dorman upgraded type from my local auto parts, I ran into an issue. When following specified torquing sequences and specs , be very careful with the 1 long stud (#7), as it will split your new manifold there if you try to torque to 89 in/lbs. Took 1st back for replacement ,and the second new one started to split at the same place. Was using a brand new Craftsman in/lb torque wrench set correctly and following instructions exactly. I've seen a lot of excellent info on this UIM issue with the GM 3.8 ltr 1995-2004 years, but never this issue with the replacement ones. If I have to change this again will definitely go with the aluminum one.

View 1 Replies

Honda - Passport :: 1999 - Procedure For Removal Of Intake Manifold

I'd like to know the number of bolts and locations for removing intake manifold for 1999 Honda Passport.

View 4 Replies

Ford Ranger / B-Series :: 2001 - Driver Side Power Window Motor Won't Stop After Window In Upper Position?

2001 Ranger 4 liter 4 door My driver side window goes up and the electric motor does not stop running when the window reaches its normal upper position. Instead it goes bang-bang-bang until I take my finger off of the switch. I'm guessing there is a limit switch that should disconnect the motor but has failed. The bang-bang (again I'm guessing) probably is some sort of a spring loaded torque limiter to protect the motor. Other than that, the window goes up & down as it normally should. I have no problem digging into the door, except with the window, door lock and outside mirror switches, I don't have a clue regarding how to get the inside door panel off. I know to disconnect the battery 1st.

View 1 Replies

Ford Ranger / B-Series :: 2001 - Adding Center Console After Removal Of Stock Seats?

I'm looking to remove my stock seats and ad bucketts to my 2001 Ranger XLT. I want to use the center connsole from an explorer. Any installation tips?

View 14 Replies

Ford Excursion :: 2001 V10 - Intake Manifold May Be Cracked

What are signs the intake manifold may be cracked? 2001 V10 Excursion....

View 4 Replies

Ford F-150 - 1997-2003 :: 2001 5.4L - Intake Manifold And Gaskets Replacement

I am about to replace the intake manifold and gaskets. I know all of that process, but first question is if there is anything i should do whilst in there. Second question; what can I do with my intake to get more power? Mainly just kind of wondering before I get my parts ordered.

View 4 Replies

Ford Ranger / B-Series :: 2011 - Oil Leak On Upper Right Front Of Motor

I saw a nice very clean 2011 ranger with 63,000 miles on it . But there looks like it has a oil leak on the upper right front of the motor. Behind the pulley that does not have any groves in it . It could be a gasket or a oil seal I don't know. Is this oil leak something common with the 2.3 engine?

View 4 Replies

Ford Ranger / B-Series :: 1998 - Torquing Upper Shock Mounting Nut

I replaced the front shock absorbers on my Ranger today and I have a question about torquing the upper mounting nut. The problem I have is that the threaded rod that is attached to the top of the shock turns when I put a socket on there and try to torque it to the proper spec. You can put a crescent wrench on the top of that threaded rod(it has flat spots) and tighten the nut some with a wrench, but the crescent wrench wants to slip and round off the top of that threaded rod. So my question is, how do you torque that upper nut without the shock spinning below?

It's a '98 2.5 ltr., 2 wheel drive with coil springs.

View 10 Replies

Ford F-150 - 1997-2003 :: 2001 - Leak Where The Water Transfer Connects To Intake Manifold

I have a 2001 F150 Super Crew 5.4. I had a leak where the water transfer connects to the intake manifold. I decided to get a new manifold rather than trying to repair it. The new manifold from Dorman came and the gaskets were built into the manifold. I torqued the manifold to specs. I replaced everything and it starts fine.

I can hear what sounds like a leak, but can't find anything. I checked every hose that is connected and they are all snug and connected. I had the check engine light checked and it said it was running lean on both sides (p0174, p0171). Also a p0122. I thought something might have damaged the Throttle Body Position Sensor, so I replaced it...but no change.

I'm still driving it everyday because I need to. It won't change gears so smoothly sometimes. The most noticeable problem is that the A/C doesn't work. It just blows hot air. And the worst part about it is...it does it even when the air isn't turned on! I just go around with the windows down...in 95+ degree heat...with hot air blowing!

This is my first time to attempt a manifold change out. What I should check?

View 4 Replies

LS / MKZ :: 2001 Lincoln - Rear Upper Control Arm Removal

I'm in the process of changing the wheel bearing and took the brakes, disconnected the sway bar, and other large bolt but can't get the upper control arm disconnected because once the nut gets to a certain point, the ball joint starts spinning with it. Tried holding the bolt at the bottom with vice grips and it still turns. I'm thinking I might have to take off the whole A arm if I can't get this nut off.

View 1 Replies

Ford Ranger / B-Series :: 1992 V6 - Upper Radiator Hose Gets Sucked Flat When RPM Is Higher

1992 3.0L V-6 RANGER

New thermostat
New Water Pump

I noticed the other day that the Upper radiator hose gets Sucked Flat when RPM is higher than Idle BAD it completely collapses IDK how it can circulate the coolant very well in this Condition. If the hoses have ever been changed But the Upper hose Really gets sucked flat. I've seen this a few times on vehicles that have been shutdown But they have always expanded upon startup and are fine....

The Lower Looks Fairly Old and only partly collapses under higher RPM.... I am going to change the Upper hose at a Minimum as its really Bad and probably a lot older than I am thinking and really Soft. I am just wondering if the radiator could be plugged up causing some of this.. Or anything else I should check into????

View 6 Replies

Santa FE SM (2001-06) :: Fluid Leaking At Intake Manifold

2.4 Santa Fe ... I just took my Car to MOT inspection and found out there's a leak at my intake manifold and it's coming out of this place. it feels like brake fluid but my brake fluid is full?? I have seen many cars but never seen a part like this before. what is it doing there and why is it leaking ?

View 6 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved