Ford Ranger / B-Series :: 2000 - Won't Start?
Jan 12, 2014
I have a 2000 Ranger 4.0L manual transmission. I just replaced the starter/solenoid on it a few days ago. I went to start it, and I got 1 click and the whole system goes dead (ie: lights, instrument panel, everything!) I checked all the fuses and the starter relay in the fuse box. All good. I tested the battery, it's charged and good. I even tried jumping it. Same problem.
I can remove power from the system, re-apply power and same issue. I'm not even sure where to start here. I checked the ground terminal on the battery. It's connected to the frame and clean. Cables are tight to the battery and clean.
What am I missing?
View 2 Replies
Advertisement
2000 ranger auto 3.0 wife said that she had problems starting the truck
She had wiggle the shifter to get it to start. Have not looked at it yet but i am think the newtrl safety Switch.
View 3 Replies
My buddy bought this 2000 Ranger 4x4 with the 3.0 and 150,000 miles for 500 bucks. After he bought it, the number 2 spark plug boot caught on fire, and turned completely to ash. So we parked the damn thing, and have been training ever since, but it did run when we parked it. We replaced all plugs, wires suspecting a bad plug (and they were all fouled). Went to start it and now its on the verge of starting, but can't quite get there. So here's what we've done since.
-Replaced coil (had it tested, failed primary test on terminal 1, and secondary on 3 and 4)
No change
-Checked Spark by grounding spark plug
Good
-Checked Fuel at rail
Good- Held until empty, primed Fuel system (key on for 3 seconds 5 times) checked again, good)
-Truck had been sitting for three months, so put in small bottle of stabil and added 5 gallons with Lucas. Primed the system about 20 times, and tried to start. No effect.
-Checked battery.
1 bad cell, 3 low on water- replaced battery. Allowed it to crank for longer (before we were jumping it) but still didn't want to.
Note of concern : After we replaced the battery and went to start it, when the key was disengaged I noticed a hissing sound coming from the radiator cap. The truck is in Upstate new york and hasn't been ran in 3 months. I'm hoping its not but thinking it is a cracked jacket or a blown head gasket.
View 8 Replies
I have a 2000 Ranger 4.0L with intermittent no start. Have spark, fuel pressure is 55psi, temp sensors are reading correctly. When there is a no start condition I can pop the scharder valve, relieve the pressure on the fuel rail and it will start.
View 3 Replies
I have 2000 Ranger 4.0L 4wd, 5sp ...
Just in the last month or so as out temps have been dropping off I've been having troubles getting her started. It happens both when the engine is cold, ie first start of the day, and after starting when warm. It did it a couple times last spring, but then all summer and fall I didn't have any problems (warm outside air temps) but, now its happening again. I'd say any time the Outside air temp is 40F or less, I am worried it won't start. IF i get her to start, everything else is just fine and she runs like a top. Here are the symptoms and what I've done so far.
When I crank I will get a couple cylinders to fire for a second or two then it falters out behaving like fuel starvation. Then I crank again right away and nothing fires... just cranking over and over. If i wait a minute and crank again same symptoms or it will fire right up. Baffling!
I thought Idle Air Control valve and sticking fuel pump relay, so I threw new parts on, but no fix.
About 75% of the time if I turn the key on, hear the fuel pump running, turn key off and on, hear the pump again x3 and then attempt the start it is successful.
Unfortunately, I don't have a code reader, or fuel pressure test equipment. The check engine light is NOT ever on. DO I HAVE A FALTERING FUEL PUMP??? I've heard thats tough to change out.
View 5 Replies
I'm having problems with my 2000 ranger 4x4 off road edition it has 262,000 miles when it runs for about a half an hour shut it off try to start it in 20 minutes or so doesn't want to start sounds like it's backfiring to the throttle body replace the crank positioning sensor replace the ignition coil still doing it.
View 3 Replies
I have 95 ranger 3.0L revs up over 2000rpm at startup then comes down slowly to a little over 1000... Changed the IAC valve still does it... When I let it warm up I unplug the IAC and idles normal and smooth about 750 RPM so I don't think it's a vac leak... What else could it be???
View 5 Replies
My 2000 Ranger standard 4.0 4x4, started spitting and sputtering the other morning just when i was gone up hills then it would quit doing it. The other evening it got to where it don't idle, missing very bad, and wouldn't even pull itself up a slight grade, and the wife said there was flames and sparks coming out the exhaust. Now it wont even try to start, it just turns over. I put a different coil pack, wires, and plugs, and still nothing. I pulled the gas line off the frame fuel filter and its shooting gas out, and I got gas to the check port on top of the engine.
View 5 Replies
I just bought a 2000 Ranger. I bought it at company auction for cheap because it wouldn't start. The battery was dead when I got to it. I put a brand new battery in it since it has 155,000 miles. When you turn the key to the on position, the theft light starts blinking rapidly. It will continue to do so for about 45 seconds if you leave the key on; then it will go out. However, if you turn the key to start, all you hear is relays clicking. The engine doesn't crank at all. I jumped the starter relay and the engine turns over. I have the factory manuals for wiring diagrams and diagnostic procedures.
The theft system relies on trouble codes to point you in the right direction for testing. I borrowed an Actron code reader (like you get at Autozone) and it says there are no codes. I'm wondering, though, if it only reads the SAE standard codes from any vehicle and not the manufacturer specific codes like the theft system. I have gone through a few of the diagnostic procedures with a multimeter, but it's like looking for a needle in a haystack without the codes. So far everything I've checked has come back ok. Any common issues this might be related to? BTW, I've gotten bits and pieces of info about this truck from the guys who drove it. Apparently, it just wouldn't start one day and was parked for the next several months until I bought it.
View 14 Replies
This has happened 4 times now over 2 weeks. The engine will turn over but will not start till I press the gas pedal. I have to keep the engine running for a few seconds by hold the gas pedal steady.After it's running you can cut the engine off and it will start right back up.
View 9 Replies
My daughter's boyfriend just bought a 2000 ranger with a 2.5. We just put a flexplate in it and it wouldn't start. Just turned over. Listened for the fuel pump and no noise. After a few minutes, it worked. He drove it home last night and said that it didn't want to work first try but worked with the second try. He drove it to church, 40 miles, and it sit for around two hours and wouldn't start, no matter how many tries.
We tried changing the relays around with no luck. We went and eat lunch and back to the truck with a rubber hammer. Then it starts on the second try without using the hammer. We got under it and cleaned the connections up and put some bulb grease on them. I couldn't get the one apart right on top of the pump itself, I was afraid of breaking it. It's been doing fine since we left the church before we cleaned the connections.
View 14 Replies
2000 ranger 3.0 auto 4wd hard to shift. Are the cables known to stretch?
View 6 Replies
I am experiencing Dismal fuel Economy, I filled the tank about 16 gallons (tank read full) and went 118 miles, I burned to about 1/4th of a tank remaining, so a rough estimate is I burned 12 gallons of fuel to go 118 miles, leaving me 5-8MPG Cruising 50-60 miles an hour.... What should I be looking for..... I have 110,7XX on the truck. it's slow as heck, it hesitates and just has no get up and go unless you really step on it. It's had a recent tune up.
Plugs were changed at 105,000 miles roughly.... I'm at a loss to know why this little truck is burning so much fuel. It's the 6 Cyl Flex fuel engine. with just normal fuel run in it...I've looked at night for arcing wires and there's no flashes... there is no real miss, I checked the intake for pirate air and fixed one minor leak and have recently rechecked it as well...I've not pulled the plugs out again yet....
View 14 Replies
This has been an issue for about 8 months now. I'm getting a misfire on cylinder 4. So far compression test, new gas filter, fuel injectors cleaned, spark plugs and wires replaced. coil pack replaced. Heater valve was leaking but was replaced.
View 10 Replies
I replaced a cracked radiator with a new one on my 2000 model B2500 a coupla' days ago, guessing at the refill, as I just got the truck and don't have a manual. Guestimate was pretty close, but I got some weirdness from the temp gauge for a bit. Temp gauge read cold (even though it was maybe sixty degrees outside) after idling for quite a bit, but would rise to operating temp if I ran the RPM's up a bit, then fall back to cold when I let it drop back down to idle.....never rose to above normal operating temperature, though.
I took a short drive down the road, stayed at normal temp, but dropped back down to cold when I parked it. Taking a peek under the hood, had air blowing out into the resevoir, bubbling like bathtub farts. All appears to be normal today, but I've gotta' take this truck for a roadtrip in a coupla' days and would like to make sure I ain't missed a step that'll send me hikin'.
What is the process of burping the radiator so's I can be sure it's all good?
View 6 Replies
OK, got a check engine light today when I fired up the Ranger.
Took it down and got the codes read it have a miss fire on cylinder 5. Picked up some plugs and wires, got to get those E3's out of there, but kind of think that's really not going to fix the problem. So that probably leaves the coil pack or injectors.
So what's the consensus on the best coils to use?
Also, being an 18 wheeler for more years than I care to remember, I've learned swapping just 1 injector is never the way to go. So whats the best type of injectors to get and where the best place to get them should it come to that?
Oh, it's a 2000 3.0L Flex fuel 5 speed.
View 6 Replies
2000 Model, The fuse keeps blowing on this. I thought it was the cruise control fuse because the cruise kept not working and when I replaced fuse it would work. Only for a little though, then I looked at manual and it says the fuse is for the brake position switch. I am presuming this is just like the old days and that is the brake light switch under the dash. They use to have two wires now there is like five. Anyways I do not see any bare wires or anything that would blow a fuse, is it common for these switches to go out or what??
View 13 Replies
I have a 2000 ranger and the right low beam went out, we changed the bulb to no avil. I thought it might be the light switch so we changed it also ,nothing!! We have checked the only ground, I can find for the lights (on the driver side under the fuse box under the hood). This problem has me stumped . Another problem that may or may not be related is the cargo light does not work either...
View 8 Replies
We have a 2000 ranger 2wd with a 5 speed transmission, we just had new tires put on last Sunday and on the way home it had a vibration in 5th gear at 55 mph whats so strange about it is, in 4th gear at 55 mph. it don't do it but when you shift it to 5th and hold it at 55 it starts.
I have checked the drive shaft and even put it on stands and shifted through the gears and held it at 55 no vibration, I guess because there is no load on the drive train. the truck only has 56,000 miles on it.
View 9 Replies
My parents 2000 Ranger has an CEL for cylinder 4 misfire, but it will clear on its own and then start up days/weeks later, is this common? Could it be an injector?
View 3 Replies
I have a misfire mystery going on in my girlfriends 00 ranger. What is going on, is there is an intermittent misfire on #4. I have an ultra gauge hooked to it, so most of the time when it does it, it will flash a pending code. A lot of the time, the pending code will go away, but sometimes it will set the PO304 code.
First I tried a tune up. New plugs and wires, air cleaner, cleaned out the throttle body. This cured it, for a short while. Then we were back to the pending code / setting code for #4.
When I pull the plug on #4 it is sometimes wet with gas. If you put a new plug in it runs fine for a while. In fact the last time we took a several 100 mile trip with it right after plug change, and it ran great. The pulled plugs re always in good condition with no burn, oil, chips or glazing. I have been using the standard autolites that are in advance auto's computer for that engine. No issues with the other 5 so I figure they re good enough.
The day after we came back I get the call... Honey its doing it again. Often to the point of having no power at all.
But it will clear itself usually, if not a new plug for #4 will cure it immediately.
So I thought something is killing this plug.... Or flooding it. SO I ran 2 cans of sea foam though it, put in a new plug and an new wire. It fixed it for a week then it did it again.
Ok I think... maybe the coil pack is bad either killing the plug or just not firing it at all? So since the pack has never been change in its nearly 300K life (to my knowledge, shes had the truck since about 60K) What the heck.... a new coil pack for the old thing.
I have not had the chance to clean the MAF but we are talking misfire on one cylinder, every now and then with no real conditions that set it off. More often than not its a pending code that you can even hear or feel and other times its a full blown miss that drags the truck down. Well for a short while until it clears up or I replace the plug.
3 cans of seafoam surely would have cleared a sticky injector. I realize it could be a bad wire to that injector but I have not had the time to tear the fiddle bits off to get to it to clean and test it... or just replace it.
Honestly Ive had a lot of cars and trucks, I don't remember ever having to replace an injector. Ive had bad wires to them but they misbehave ALL the time. This problem is so intermittent its freaky.
She says it does it mostly when its cold or not totally warmed up. Almost always, by the time the engine is hot it goes away.
And hot for this truck is over 185F, which I think its too cold to be running and the thermostat needs changed BUT she thinks cool=good. I keep telling her no, cool is often not good, the engine needs to be up to the operating temp.... which to me means 190-200. Her ranger runs between 170-180 all the time. I doubt thats causing the problem but still.... I think new thermo is in order.
My thinking is since it runs so cool all the time, the issue might be related to a spike in the temp over 180 ish, that gods forbid is opening a crack somewhere to suck air or lose compression.
And a compression test is my next step on #4 if/when it does it again. Now I have had cracked valves before, I don't recall them acting this way. After all sometimes the thing will go 100s of miles under different driving conditions and run fine. I don't think a cracked valve would be that nice.
Shes getting @18 MPG mixed driving, when it runs t runs like a bear. It always fires right up. There is no smoke, white or black. There is no water in the oil, no oil in the water. No audible exhaust leaks. No ticks knocks or oddball noises. For its age and miles almost 300K it runs perfectly.
Well until it has its intermittent issue with the misfire, that isnt bad enough to actually set the code.
View 14 Replies
