My 2000 ranger in 4x4 high never did this. And in 2wd it doesn't pull at all...
When in 4x4 high it pulls hard to the left ?????? is left not working? It has automatic hubs ...
I've been replacing my steering components over the past month and have fixed all the previous issues other than this one that's got me stumped. After I make a hard left the steering will pull left (very hard) until I either turn the wheel right or hit a bump. Sometimes when going immediately from a left turn to a right turn (or vice versa) I can actually feel a slight pop as it starts to pull.
The order of repairs thus far has been: new power steering pump, new inner & outer tie rod ends, professional alignment, new steering box with both lines. The shop and I both agree the ball joints are good. I've jacked my truck up by the frame and removed the wheels to check for steering/suspension play but have not been able to find any. 180k miles on the chasis.
I am currently working on a 97 ranger with a 4cyl and 5 speed. its having some idle issues that i cant seem to pin point, you can start it and it will idle rough then when you rev it up it chugs real hard then dies. used my scan tool and all the sensors are good, fuel pressure is good, good compression, all 8 plugs are firing good and no codes. The other deal that has me a little confused is when I unhook the hose that runs from the air intake tube to the valve cover, I get a lot of vacuum at that port on the valve cover that the hose hooks to. Also when I plug it and pull the dipstick, I get vacuum at the dipstick tube. never seen this before but at the same time I've only messed with very few of these trucks so I don't know whats normal.
View 6 RepliesMy 40 Ford pickup is on an 86 Ranger chassis and uses the stock Ranger steering gear. My question is about the connections on the steering box. I'm using a GM power steering pump and several steering gear vendors have told me that outside of needing to adjust the pressure for the correct feel, the combo works. I fired the truck for the first time tonight but the steering wheel went crazy, shaking around and finally spinning on it's own to a hard left.
Some quick research leads me to believe that I have the lines reversed but it would be great to know for sure. I did manage to find on e diagram of a Ford PS box on Google and it shows the lines reversed of what I have set up on my truck and I can't for the life of me remember how I figured out what the plumbing should be when I installed it. Which port on the box is the inlet and which is the return?
2000 ranger 3.0 auto 4wd hard to shift. Are the cables known to stretch?
View 6 RepliesWhen I make a left turn I have a horrible grinding noise. Only when I turn left and at any speed.
View 2 RepliesI've got a 1995 Ford Ranger that pulls hard to the right. It has always pulled to the right a little, but recently it has been worse. About a year and a half ago I replaced all four shocks, the two front tires, and had all four wheels aligned, but this did not stop the slight pull to the right. I get it back from the mechanic yesterday, and he tells me that there is a little bit of wire showing on the inside or the front drivers side tire.Is there some kind of joint or something in the steering that may be worn out that needs to be replaced? If so, how much does something like this cost to replace?I've been slowly replacing everything on my truck that needs to be replaced as I get the money, but it seems that lately it's just got way more expensive. I know that it's not a cheap fix for something like this, but I just wish it wouldn't happen all at once
View 2 Replies2000 Ranger 4R44e transmission.Hard shift from 2-3 gear and when i run about 35-40 mph and brake then acelerate it downshifts hard . Whats wrong with it?
View 14 RepliesI have an 03 Ranger 4.0 4x4 5 speed. It has no power, can't give throttle or it bogs real bad. Baro shows 18in vac with KOEO. When running it has 15in vac. Replaced MAF, fuel pump, and fuel filter.
View 4 RepliesJust replaced break pads and rotors. Inner pad on left side was gone leading me to believe slides were not working properly. Pulled apart, cleaned and greased everything, and replaced pads and rotors. Calipers seem to be working fine. Now when I break hard, the truck pulls badly to the left. When I break softly, it seeks normal. My front end is a bit out of whack and veers just a bit to the left. Do you think this is my issue with the breaking ? I'm getting new tires and an alignment soon but was just curious.
View 3 RepliesI have a 2000 XLT, V10, Auto, 4" suspension lift on 315/75R16. It recently started pulling to the left and has been getting worse. At <5mph the steering wheel will pulse to the left almost a quarter turn if you let it go and hold there. At actual driving speeds it feels like a constant pressure. The tire appears to have a wobble to it when driving, I know this because my wife drove followed me in it so I could observe.
It also turned easier to the left than to the right when I jacked up the front end and both wheels spun with ease. I have checked the tire rod, drag link, ball joints, and wheel bearings. They all checked out. The last things I can think to do would be to check the steering stabilizers, I have the dual inline set up, or swap the front tires and see if the problem moves from left to right.
Two days ago, I was driving on a North GA steep, windy, mountain road in my 2002 v6 4.0 Ranger. All of a sudden, i started revving real high (about 4000rpms) and getting no power (20mph). I pulled over immediately and transmission fluid was pouring, by the quart, out of my truck. I didnt get to look exactly where it was coming from, since i backed away once i saw a small flame coming from the leak. i then called a tow truck (assuming it was a seal or a hose break) and had it towed to my house.
I started investigating the possible problems and didn't really see anything noticeable under the truck (not that I was expecting to). So what I did was put three quarts of transmission fluid in the dipstick hole and put in gear to see if I could spot a leak. nothing. then I drove it around the block to get it warmed up and put a little pressure on the transmission by driving up a semi-steep hill to see if that would spark the leak again. still no sign of the a leak.
And finally, when I went to go check the dipstick after my test drive, it read to be above the cross hatched area, hence being overfull. What my next step should be?
OK so when I'm driving on freeways or highways and I have to break hard for some reason my steering wheel always pulls in some direction I don't want it to go. forcing me to hold it straight I've lived with this problem for a while but I'm doing 500 miles trips this weekend in the car and am concerned about if I had to brake at higher speeds etc., what might cause my steering wheel to pull left and right... 2003 nissan maxima ...
View 7 Replies2001 Ex 7.3 4x4 with 4" lift (6" with 37" Pro Comp tires)
All new front end steering components.
All new Shocks (bilstein)
All tires properly inflated to same PSI
All new brake rotors, calipers, caliper mounts, and pads.
When under hard acceleration the vehicle pulls to the left and I have to compensate by steering to the right. Under deceleration the vehicle pulls to the right and I have to compensate by steering to the left.
I am about to change all four brake lines to Braided Stainless Steel lines, replace all leaf spring bushings with polyurethane, and install a rear anti-sway bar. I'm going through this methodically enough or am I just building a brand new truck one part at a time?
So, I picked up my new car today, a 2012 obsidian ISF with 53,000. I'm driving it back from Texas to Georgia in the morning but after driving it for the first 100 miles I notice a pull to the left under hard acceleration and to the right when I let off. I've never driven an F before and I'm coming out of an IS350. I haven't had a chance to check tire pressures yet but I notice the right rear tire is a Dunlop and all other 3 are Bridgestones. Could this be the cause?
View 12 RepliesMy 2003 F250 6.0 pulls to the right when driving at any speed. In order to keep it going straight the steering wheel must be slightly tilted to the left, not much but a little. When the brakes are applied hard it will go to the left slightly if you are not holding the wheel good. Neither of these are terrible, just a nuisance. I'm worried about uneven tire wear too. One front wheel bearing was replaced a few weeks ago. It had this problem before that and still does after. Does this sound like an alignment or maybe something more?
View 13 Replies2004 accent manual shift. car drives well, but when i step on the gas, it sudenly pulls to left. when i release gas, it goes back to straight driving. motor mount??? anything else come to mind??
View 1 RepliesThe blinker in my 98 Mazda B4000 does not deactivate when turning right/left. The multi-function switch was replaced last year with an OEM part.
View 2 RepliesI recently acquired a B4000(for a steal!), had it almost a month now and im starting to notice a few problems, all driveline related (I think).
1. Have a "grinding/rubbing" noise in a LEFT turn only. It is a 4x4 and I haven't turned a bolt on it yet, save for very minor stuff. Since this particular model has some costly parts, I'm trying to prevent buying unnecessary parts! I have a set of 31 x 10.50 on it, and even though there is some minor tire rub, im 90% certain this is not the case.
2. Has a somewhat "hard" shift when going into O/D(I think), doesn't do this all the time, I wonder if problem #2 and #3 are related.
3. Appears to be about 1in slack in the rear driveline, wondering if it is the rearend, and specifically the spider gears or pinion?
4. Also seems to be just a LITTLE slack in the front left CV axel, is this something I should be worried about? the front right is good and tight, Tcase shifts like its suppose to.
I noticed that my ABS was engaging when I would slow down to a stop while turning left. I pulled the fuse for the ABS just to make sure that's what was causing the pulsating brake, and it was. Anyway, if it's an ABS sensor problem, would it be the front passenger side sensor if it's only happening when I turn left? Is there a way to test this. Would a scanner detect it? It hasn't been throwing a code or anything. Just the ABS engaging while braking and turning to the left when it shouldn't be.
View 6 RepliesSometimes the LR brake skids MUCH too easily under just moderate braking. Other times it works normally. It's unpredictable. I may drive it for weeks with no trouble and then have a few days in a row when the problem comes back.
It usually happens when the truck has been sitting for a while (several hours or days). sometimes it goes away after driving for 10-15 mins, other times it sticks around a few days then stops.
I had Les Schwab inspect the brakes several months ago and they could find nothing wrong. It's been happening for a year or more.
It's a '99 Ranger, 2 wheel drive with ABS.