Ford Ranger / B-Series :: 2000 - Parking Brake Cable Route?
Feb 3, 2017
I bought 2000 Ranger with rear half of the frame cut and welded.
The mechanics who did this did terrible job of putting things where they belong. I rerouted wiring harness and rebuilt EVAP lines, but cannot figure out what is the correct route for parking brake cable.
Currently some part of the parking brake cable is sitting on the leaf spring. It may also be missing some mounting brackets or clips. Looking for a picture or diagram showing parking brake cable routing?
View 2 Replies
Advertisement
I'm having a hard time trying to figure out to detach the cable from the pedal assembly. The place where the cable attaches is so hidden by various plates, pawls and springs that there is no access. Also the whole assembly is put together with rivets so there's no easy way of taking it apart. Is there some trick to getting the cable out?
Also, I need to find out exactly where the cable goes through the floor pan. I'm in the process of fixing the rust on this. My 2000 XLT 4x4 and the floor pan and rockers were so rusted that there was no evidence of where the cable went through the floor pan! I assume it's supposed to go through the channel right next to the inner rocker but where exactly? A simple measurement from the back edge of the A-pillar is all I need.
View 2 Replies
I bought a 2000 Ranger 4x4 3.0L auto today from the neighbor guy sight unseen with a "bad tranny" for $400. I'm very unfamiliar with the Ranger family, but long story short:
When moving the shift lever, the trans doesn't engage. It needs to be engaged from underneath. Do the cables tend to stretch, or break? I can't find any adjustment on it anywhere.
View 5 Replies
I've noticed my RR emergency brake cable's outer casing rubs hard against the RR shock, such that it's rubbed through the cables plactic covering & is going after the metal jacket.
It's a 99 4X2 4dr extra cab long wheel base.
Notice this on your Ranger, LWB model, or for that matter any wheel base Ranger???
View 14 Replies
The parking brake instrument cluster lamp is enabled by a small switch at the foot operated park brake mechanism. The switch is attached to chassis electrical ground. The switch has one wire attached to it. So when the switch is enabled it connects chassis ground to the wire therein turning on the cluster lamp. With the wire disconnected from the switch the lamp stays on. This tells me the wire is grounded somewhere. Brilliant deduction eh?
So here's my question. How/where that wire is routed? I lose sight of it approx. 2-inches from the switch where it disappears behind the brake mechanism mounting bracket. I plan to unbolt that bracket to see if that might be where the wire is being shorted to ground. But if it's not pinched there, where do I go from there?
(2001 Ranger, 4liter-2wd)
View 3 Replies
When I set the parking brake last night, there was a loud pop and the pedal suddenly went soft to the floor and would not spring back when I pulled the release. The pedal doesn't spring back up when I pull the release lever, but I was able to pull it back up by hand to get the dash light to go out. That works, but without the tension from the brake cable the pedal works back down and the dash light comes on.
When I got out of the driver's seat, there was a cable laying on the ground right under the front door. The cable snapped right in front of a metal cable joiner. What is involved in fixing this?
View 4 Replies
I use a vent mount for my phone and my old car had the aux-in by the radio so I used a little retractable cable to my phone. Now in the prius the aux-in jack is way in the back of the arm rest what is the best way to route the cable there?
No nav, so no bluetooth streaming for me.
View 1 Replies
How to replace the parking brake cable from the pedal down to the connector on the frame? We got a 2000 F350 in the shop with a bad cable, and i never did one. And I don't really want to mess this thing up trying to figure out how to change it.
View 6 Replies
So here it is, who out there with a 2012 SCREW can tell me how their rear parking brake cable is routed around the axle? The reason I ask is mine is routed under the axle and that just seems like a really screwy design. I would think any time the rear suspension was unloaded it could have the potential to engage the parking brake by the axle pushing down on the cable. My father has a 2014 and his isn't routed that way. I've also looked at a lot of pictures on the internet and haven't found any photos that show the cable routed under either. Is something off on mine, or is mine routed correctly and I just have not found any pictures that show it routed the same as mine?
View 1 Replies
What is the procedure to remove the parking brake cable from the axle? It looks like the cable has a locking device like the fuel lines but heavier. How do you get that thing out of there without destroying it?
View 9 Replies
I am installing a wiring harness in my 2007 Camry SE so that I can tow a small flatbed utility trailer I have to carry my kayak on trips. I have the wiring harness all installed except for I now have to route the power cable for the harness from the trunk to the battery in the front of the car. The instructions give no suggestions on how to get the wire to the battery other than to avoid hot parts and suspension parts.
What would be the best and easiest way to get the wire to the front? I'm not well versed in car mechanics or how to take things apart so I would prefer the easiest, most direct way if there is one.
I have already found a grommet in the trunk with a factory wire harness going through it to the bottom of the car so I can route my wire through there, but after that where to go next. The only thing I can think of is there is several brackets holding the 2 fuel lines and the 2 rear brake lines, there is a open spot between the 2 fuel lines so I could use the empty spot in those brackets to hold the wire for most of the way to the front, do fuel lines get hot at all? Do you think it would be safe to route the wire that way?
As for getting into the engine compartment, how to do that without getting in the way of the front suspension while keeping the wire away from the transmission and axles.
If this is too complicated to do myself, my dad has a friend who is a electrician and likes to restore cars that could do it for me but he is almost always busy, thus hard to get a hold of and I like to try and learn some things about my car and do as much as I can on my own.
This is the trailer light wiring harness I have, there is a link for the instruction manual there too
[URL]
View 14 Replies
My battery went flat and to compound my misery, when I went to open the hood, the cable was snapped. How I can open the hood without using the release cable ? I'd rather not have to pay for it to be taken to the mechanic and then also pay to have the battery changed !
View 3 Replies
I'm re-doing the parking brake as part of a rear brake job on my 2009 F250. I need to disconnect the intermediate brake cable at the equalizer, but am having trouble. I've got slack in the cable, but can't push hard enough to get the swaged cable end to move within the connector that's between the equalizer cable and the intermediate cable.
Is there a special tool or some trick to this? If push comes to shove, I can cut the connector (assuming I can get a replacement), but would rather not.
Also, any particular trick to disconnecting the cable to the parking brake lever at the wheel? With that huge spring between the cable bracket and the end of the lever, I haven't been able to move the cable end enough to disconnect it from the lever. Since I don't have the intermediate cable disconnected, could that have something to do with it?
View 7 Replies
I'm working on an '05 F350 King Ranch dually, and I'm pretty sure the pb cable is stretched. I recently replaced the shoes in the pb assembly and adjusted the tension while I was in there, but it still barely holds. My next culprit sounds like a stretched cable, and I have a complete set for a new one, but I'm having a hell of a time getting the old one out. The link that holds the front and intermediate cables together won't pry open with any tool I have, and I've broken two drill bits trying to drill out the nub holding the front cable in.
View 5 Replies
After taking apart my instrument panel to change the bulbs, I went to reconnect everything, but now the gear shift indicator isn't working. I can change gears fine, and everything else on the instrument panel works just fine.
The copper cable that connects to the shifter doesn't move when the shifter does. Is there a way to fix this problem, or do I need to find a replacement cable?
View 2 Replies
so i changed the speedo cable and speed sensor in my 93 ranger, but still getting the speedometer bounce. what could be next? the speedo housing in the cluster? lubed the inner cable, made sure nothing is kinked or sharp bends. Put in a new vehicle speed sensor while i was at it just bcuz. cruise control does not hold a steady speed either but i think the 2 are not related. I'm leaning towards the cruise control servo as to why it does not hold a steady speed. Most of the time once i get to around sixty i'm basically driving by ear bcuz the speedo bounces from 60down to 55 and back up.
View 3 Replies
I noticed the rear parking cable's one end hanging. Not sure how to connect it. Appears a part is missing.
View 7 Replies
My left parking brake cable seems to stick. The parking brake shoes and springs appear to be fine. I have ordered a new left parking brake cable and need to know how to remove the old cable and feed the new cable to the hand brake lever. Looking for the brake cable removal procedure and diagrams?
View 2 Replies
i am putting in new emergency brake cables i have the cables installed except into the backing plate sleeve i tried to get old 1s out but the whole sleeve came out are these sleeve available for purchase i cant seem to locate any.
View 1 Replies
I broke my emergency brake cable on my 2000 chevy silverado. It broke before the cable splits to two wires to go to the two rear tires. I would like to know if this is something I can handle myself. My biggest question is how I get access where the wire attaches to the pedal itself.
View 2 Replies
My buddy has 2005 Ford Ranger, 4.0L V6, manual with 4WD. It cranks fine, shifts through gears, but it will not move. We're thinking something to do with the parking brake, but I don't have much knowledge about brake systems. A cursory inspection showed a cable without much rust, some rust on the rear drum brakes, and around the mounting where the brake cable runs into the brake drum. I can pull downward on the cable about three inches, so it doesn't seem like the cable is pulled too taut. The pressure on the brake pedal feels about normal.
(edit: something sort of important I forgot to mention, which is why I don't think it's the transmission. In neutral, we cannot push the truck. When pushing from the rear, it will rock back and forth a few inches. When pushing from the front, the truck will not budge at all with two guys pushing on it.)
What sorts of tests can we do to pin down where the problem lies? If it is the parking brake, how can we loosen it up enough to get the truck moving to a shop (or at least to the garage where we can get to the brake shoes)?
View 17 Replies
