I have a 2000 Ranger 4.0L with intermittent no start. Have spark, fuel pressure is 55psi, temp sensors are reading correctly. When there is a no start condition I can pop the scharder valve, relieve the pressure on the fuel rail and it will start.
View 3 RepliesI have 2000 Ranger 4.0L 4wd, 5sp ...
Just in the last month or so as out temps have been dropping off I've been having troubles getting her started. It happens both when the engine is cold, ie first start of the day, and after starting when warm. It did it a couple times last spring, but then all summer and fall I didn't have any problems (warm outside air temps) but, now its happening again. I'd say any time the Outside air temp is 40F or less, I am worried it won't start. IF i get her to start, everything else is just fine and she runs like a top. Here are the symptoms and what I've done so far.
When I crank I will get a couple cylinders to fire for a second or two then it falters out behaving like fuel starvation. Then I crank again right away and nothing fires... just cranking over and over. If i wait a minute and crank again same symptoms or it will fire right up. Baffling!
I thought Idle Air Control valve and sticking fuel pump relay, so I threw new parts on, but no fix.
About 75% of the time if I turn the key on, hear the fuel pump running, turn key off and on, hear the pump again x3 and then attempt the start it is successful.
Unfortunately, I don't have a code reader, or fuel pressure test equipment. The check engine light is NOT ever on. DO I HAVE A FALTERING FUEL PUMP??? I've heard thats tough to change out.
1997 2.3 Ranger w/ 160,000 mi. Every few months it won't start, sometimes after just having been running fine. Symptoms:
-the dash lights will be dim or off completely
-the chime will be softer than normal
-the headlights will not work, or be dim
-the starter will sometimes briefly click, sometimes crank once, sometimes do nothing
-the emergency flashers will sometimes click much faster than normal
-if during one of these "episodes" it does start, the battery light will sometimes flutter on and off, and the meter will flutter a little higher than normal. The next time I stop it, it typically will have the same problem.
-it will typically start if i get it jumped
My battery, starter, plugs and wires are all fairly new. On occasion, when it is having this problem, and I am trying like crazy to start it, if when I turn the headlights on and they are no longer dim, it starts right up and runs fine.
2000 ranger 2.5 245000 miles. code po171 and idle problem has come back. Replace ICV, EGR, MAF, PVC, check fuel pres, air cleaner, plugs, wires, O2, check for vac leaks, Intermittently coasting at 20mph out of gear (stick shift) engine revs to 2500 rpm and holds until i brake to a stop then it idles down. So I disconnect the ICV and it runs perfect. (its a new ICV) something is telling the ICV to open up. a month ago it did the same thing when i replaced the EGR the idle problem cleared up so I thought that was it.
There is a relationship between the truck speed and the engine speed but how does the engine speed know the truck is moving when its out of gear. It work perfect for a month all of a sudden it starts this problem again. I am thinking of taking it to the ford dealer for a diagnostic test but I don't know how specific they can get on whats wrong I don't what to them to just say "oh you have a vac leak" . . . I know a 171 could be vac leak but the problem is so dramatic and off again on again it seems more like a part problem then a vac hose is either leaking or not.
i have a 96 ranger with a 2.3l engine sometimes it will start right up and sometimes it has to crank 4 or 5 times to start i just gave it a tuneup and changed the oil and filter. should i run sea foam through the oil system,it sat for about seven years and i need to convert the idiot gauge to a real gauge.
View 2 Replies2000 ranger auto 3.0 wife said that she had problems starting the truck
She had wiggle the shifter to get it to start. Have not looked at it yet but i am think the newtrl safety Switch.
I have a 2000 Ranger 4.0L manual transmission. I just replaced the starter/solenoid on it a few days ago. I went to start it, and I got 1 click and the whole system goes dead (ie: lights, instrument panel, everything!) I checked all the fuses and the starter relay in the fuse box. All good. I tested the battery, it's charged and good. I even tried jumping it. Same problem.
I can remove power from the system, re-apply power and same issue. I'm not even sure where to start here. I checked the ground terminal on the battery. It's connected to the frame and clean. Cables are tight to the battery and clean.
What am I missing?
My buddy bought this 2000 Ranger 4x4 with the 3.0 and 150,000 miles for 500 bucks. After he bought it, the number 2 spark plug boot caught on fire, and turned completely to ash. So we parked the damn thing, and have been training ever since, but it did run when we parked it. We replaced all plugs, wires suspecting a bad plug (and they were all fouled). Went to start it and now its on the verge of starting, but can't quite get there. So here's what we've done since.
-Replaced coil (had it tested, failed primary test on terminal 1, and secondary on 3 and 4)
No change
-Checked Spark by grounding spark plug
Good
-Checked Fuel at rail
Good- Held until empty, primed Fuel system (key on for 3 seconds 5 times) checked again, good)
-Truck had been sitting for three months, so put in small bottle of stabil and added 5 gallons with Lucas. Primed the system about 20 times, and tried to start. No effect.
-Checked battery.
1 bad cell, 3 low on water- replaced battery. Allowed it to crank for longer (before we were jumping it) but still didn't want to.
Note of concern : After we replaced the battery and went to start it, when the key was disengaged I noticed a hissing sound coming from the radiator cap. The truck is in Upstate new york and hasn't been ran in 3 months. I'm hoping its not but thinking it is a cracked jacket or a blown head gasket.
I'm having problems with my 2000 ranger 4x4 off road edition it has 262,000 miles when it runs for about a half an hour shut it off try to start it in 20 minutes or so doesn't want to start sounds like it's backfiring to the throttle body replace the crank positioning sensor replace the ignition coil still doing it.
View 3 RepliesI have 95 ranger 3.0L revs up over 2000rpm at startup then comes down slowly to a little over 1000... Changed the IAC valve still does it... When I let it warm up I unplug the IAC and idles normal and smooth about 750 RPM so I don't think it's a vac leak... What else could it be???
View 5 RepliesMy 2000 Ranger standard 4.0 4x4, started spitting and sputtering the other morning just when i was gone up hills then it would quit doing it. The other evening it got to where it don't idle, missing very bad, and wouldn't even pull itself up a slight grade, and the wife said there was flames and sparks coming out the exhaust. Now it wont even try to start, it just turns over. I put a different coil pack, wires, and plugs, and still nothing. I pulled the gas line off the frame fuel filter and its shooting gas out, and I got gas to the check port on top of the engine.
View 5 RepliesI just bought a 2000 Ranger. I bought it at company auction for cheap because it wouldn't start. The battery was dead when I got to it. I put a brand new battery in it since it has 155,000 miles. When you turn the key to the on position, the theft light starts blinking rapidly. It will continue to do so for about 45 seconds if you leave the key on; then it will go out. However, if you turn the key to start, all you hear is relays clicking. The engine doesn't crank at all. I jumped the starter relay and the engine turns over. I have the factory manuals for wiring diagrams and diagnostic procedures.
The theft system relies on trouble codes to point you in the right direction for testing. I borrowed an Actron code reader (like you get at Autozone) and it says there are no codes. I'm wondering, though, if it only reads the SAE standard codes from any vehicle and not the manufacturer specific codes like the theft system. I have gone through a few of the diagnostic procedures with a multimeter, but it's like looking for a needle in a haystack without the codes. So far everything I've checked has come back ok. Any common issues this might be related to? BTW, I've gotten bits and pieces of info about this truck from the guys who drove it. Apparently, it just wouldn't start one day and was parked for the next several months until I bought it.
This has happened 4 times now over 2 weeks. The engine will turn over but will not start till I press the gas pedal. I have to keep the engine running for a few seconds by hold the gas pedal steady.After it's running you can cut the engine off and it will start right back up.
View 9 RepliesMy daughter's boyfriend just bought a 2000 ranger with a 2.5. We just put a flexplate in it and it wouldn't start. Just turned over. Listened for the fuel pump and no noise. After a few minutes, it worked. He drove it home last night and said that it didn't want to work first try but worked with the second try. He drove it to church, 40 miles, and it sit for around two hours and wouldn't start, no matter how many tries.
We tried changing the relays around with no luck. We went and eat lunch and back to the truck with a rubber hammer. Then it starts on the second try without using the hammer. We got under it and cleaned the connections up and put some bulb grease on them. I couldn't get the one apart right on top of the pump itself, I was afraid of breaking it. It's been doing fine since we left the church before we cleaned the connections.
Ok I have 94 B2300 and about every 3rd or 4th start the ECU relay will not come on / energize which the the fuel pump relay doesn't come on either to prime the fuel system... so no start! It's very intermittent and sometimes the only way I can get the truck started is by pulling out the ECU relay and plugging it back in even sometimes that doesn't work too. Is it a bad relay or bad base the relay plugs into or is the ECU/computer going bad or is there wiring messed up in my ignition switch? Is there a known problem like this with these trucks?
View 7 RepliesI have a 96 ford ranger 4cyl 5 spd. I've only had it for a month or so, but I've noticed on cold mornings my odometer won't work. The trip or the total mileage. I can hear the odometer cable clicking. Once the cab gets warmed up it'll start working. It's only happened twice, at about 50 degrees or lower, so I can only imagine what'll happen once winter kicks in. Where to go from here? I was thinking maybe it needs to be re-lubed or something...
View 9 RepliesI figured something out on my ranger that has been bugging me for a while it was a third cly misfire so I changed the plugs and it went away for a while.the po told me he had just changed the plug wires so i didn't mess with those and it was an intermittent misfire so i changed the brain box because it was 15.00 at pull and save and it had been all updated boy did it run smooth for a while then the misfire came back. So I decided to check the 3rd cylinder plug wires and found out the one that is hard to change on the drivers side was badly rusted so i borrowed one off my windstar it was a little longer but boy does it run smoother and it doesn't die all the time and chug chug all the time now i just need to change the battery. i have already changed the clutch and the tranny twice i took one out of an 88 and it fit just fine by the way the engine is a 2.3 8 plug engine with over 230,000miles on it my next project is a timing belt and a heater core won't that be fun and yes i smell the antifreeze inside and don't like the stop leak like the last person put in.
View 2 RepliesI just bought this truck last week. It has 55k on it, so I'm guessing it sat a lot. It seems to run great, but today on my drive to work it started having an intermittent bogging down when accelerating. It didn't seem to matter if I was accelerating soft or harder, or what rpm I'm at. It also did it when it was cold pulling off of my street and it did it once or twice after 15-20 minutes of driving. It just feels like I let off the gas for a moment, I can watch the tach drop about 500 rpm and then just as quick it picks right back up and is fine for a bit. I don't have any check engine light.
View 5 Replies1997 Ranger extended cab, 222k mi., 4 cyl, standard transmission. Shifting got worse until it finally died and the mechanic replaced the clutch "kit" and slave cylinder.
It still fights back going into 1st, 2nd, and reverse. But it is intermittent. If I put it in neutral, depress the clutch, and start the vehicle, then, after a few seconds wait, when I try to go into 1st (or reverse), it fights me back, forcing me to pause and apply about twice the pressure I should need to go into gear. When I go forward in 1st, and am ready to shift to 2nd, it fights back so that I have to pause just a bit and apply more pressure than I should for it to go into 2nd gear. 3rd, 4th, and overdrive are FINE. Also, the clutch seems to disengage about halfway down, where I was expecting it to disengage after only 10 -20% depression.
The mechanic doesn't see the problem (or won't admit it). Is there an adjustment to make the clutch disengage with only 10-20% depression instead of the 50%? Is that something I should be worrying about?
Is there some other problem? Like maybe the synchromesh mechanism in the transmission itself not bringing the transmission rotor to engine speed soon enough (wear on the synchromesh)?
When it was new, it went into ALL gears with ease, no fighting back, and it starrted doing this after about 150k miles. Now, at 222k mi., even with a new clutch, plate, throughout bearing, and slave cylinder, it still seems partially stuck going into 1st, 2nd, and reverse.
I just don't want to start replacing things until I can get a correct diagnosis as to what is causing the problem.
Sometimes the LR brake skids MUCH too easily under just moderate braking. Other times it works normally. It's unpredictable. I may drive it for weeks with no trouble and then have a few days in a row when the problem comes back.
It usually happens when the truck has been sitting for a while (several hours or days). sometimes it goes away after driving for 10-15 mins, other times it sticks around a few days then stops.
I had Les Schwab inspect the brakes several months ago and they could find nothing wrong. It's been happening for a year or more.
It's a '99 Ranger, 2 wheel drive with ABS.
I am normally on the super duty side but I have a 2002 ranger 3.0 auto EX cab if that matters with this issue. My cruse control will only come on rarely but when i does it works fine. Most of the time when I hit the ON button the indicator only blinks like a "relay" of some sort is not latching up. Don't know if this is an all solid state system or if there are electro mechanical relays involved as well. When it does work and I hit the brakes it will drop out completely rather than just disconnect from the controller and need to hit the ON button again, usually with no results.
View 8 Replies