Ford Ranger / B-Series :: 2000 - No High Beams And Indicator?
Jan 19, 2007
I have no High Beams and the little blue light does not come on in the dash. I also do not have flash to pass. I searched through the older posts and found other similar problems but their dash indicator came on. I changed both bulbs this morning and checked the 2 fuses in the panel (#4 & 8 I believe.)
What to check next? I don't see how you would get the headlight switch out of the dash to change it, the fuse panel is directly behind it. Does it get moved to access the switch? Should I be looking at the dash on/off switch first or the column lo/hi/flash to pass switch?
View 6 Replies
Advertisement
The turn signals and high beams do not work on my 1998 ford ranger xlt 4x4. I have replaced the multi function switch, the yellow flasher relay checked all fusses and all are good. What could be the problem?
View 7 Replies
I have a 2011 ford ranger XL and I get no high beams. My low beams work fine but when I try to either activate the high beams or pull for the flash to pass they do not illuminate and the indicator on the dash doesn't come up either. I have replaced the fuse with a fresh one, even though it didn't need to be replaced, and also replaced the headlights as well cause one was burnt out.
View 1 Replies
I have 95 ranger 3.0L revs up over 2000rpm at startup then comes down slowly to a little over 1000... Changed the IAC valve still does it... When I let it warm up I unplug the IAC and idles normal and smooth about 750 RPM so I don't think it's a vac leak... What else could it be???
View 5 Replies
My ranger sounds like it's revving up real high when I take off but don't have much power. Know what this could be?
View 5 Replies
Truck is a 2003 Ranger EDGE 2wd auto w/140K miles (looks new) that was a one owner truck I recently bought. Came from Texas and is clean and was well maintained I got all service records up until I bought it in the fall last year. OK now the problems...
First...it has a high idle in the mornings when cold about 2000RPM. After it warms up it settles to about 800-900RPM but is VERY ROUGH to the point where it feels it will stall. I DID replace the spark plugs and the plug wires look newer and are not OEM. I DID remove and clean the IAC and it does not look very dirty but I did slightly clean it anyway.
When I did this I disconnected the battery for 20min. After I put it back together it ran smooth for about the first 10 minutes then same rough idle came back. I was told this truck has no EGR so that's not an issue. There are NO CODES and when I ran my pocket scanner nothing comes up either. Should I just go to NAPA and get a new IAC anyway? What else can I do?
View 1 Replies
Low beams work fine. When I push the Multi-Function lever on the column forward to activate the high beams, I have no lights at all. When it is in low beam (middle) position, low beams work fine. When I pull back for click to pass, only the low beams are active. No high beam indicator in instrument cluster. I have:
1. Replaced both headlight bulbs
2. Replaced the multi-function switch on the column. Checked test pins on switch (MF) they are hot when in either high beam position or click to pass position
3. checked fuses (interior)
#8 - power on both sides of fuse
#16 (15a) High beam headlamps, instrument cluster. ***NO POWER ON EITHER SIDE***
4. checked fuses (engine compartment)
#10 - power on both sides
#21 - Power on both sides
#23 - power on both sides of fuse
View 14 Replies
First time driving my 'new' 2000 7.3 Ex and the high beams won't stay on for more than a minute or two. Playing with the switch in the driveway, they came on after a minute of not being run, but after throwing the switch a few more times, they wouldn't come on again. The indicator light corresponds with the high beam function. I'm thinking a relay is going bad? The switch is brand new and the bulbs are definitely working. Also, I did not get an owners manual with the truck, and the fuse diagram I found online did not match the box at my left knee.
View 11 Replies
My truck only has low beams. When you move the stalk on the colum backwords it changes nothing, when you move it forwards the low beams go out but the high beams do not come on.
View 14 Replies
I have checked fuse 46 and 47, and installed new headlight bulbs. I have high beams, but no low beams. I have searched this topic but no one has the same prob it seems. My headlight switch has broken. Could it be the headlight switch?
In my manual, it says the 2002 has a fuse panel behind the glove box. I took glove box out but it doesn't look like a fuse panel.
View 5 Replies
I recently installed new halo HID headlights in my 2003 f150 with HID bulbs and ballast the passenger side worked and the drivers side didn't nth lights wired exactly the same. I switched everything from the passenger to the drivers side still nothing I switched everything back to passenger side and they don't work now. I tired regular bulbs in the passenger side an it worked then on the drivers side and it worked for a split second and went out and then I retried t on the passenger side and it worked for a split second and went out a now neither are working. I checked all the fuses and their good. What the problem could be?
View 5 Replies
98 Ranger 4x4 4.0 L Supercab. Today I replaced my instrument cluster lights. When I put everything back together i noticed my gear shift indicator is off and I cant shift into 1st or 2nd. What did I screw up?
View 5 Replies
It ford related but I just bought a used car that has hid low beams and when you turn on high beams there is no light at all. The blue light on dash comes on and head lights go off. I just got this car 2 days ago and haven't really looked into it.
View 5 Replies
So with 172,000 miles my truck has started a new trick. When I turn on the turn signals theyll flash or interrupt normally for a few times then stop. After I turn the signal lever off and back on again they start to flash again only to stop after several times. This happens to both the left and right hand sides. The emergency flashers seem to work alright. Is this a function of the indicator flasher SF631? If so, were exactly is it located?
View 5 Replies
I have a 2010 prius the basic model I turned the lights and both headlights went out they only worked on high beams.
I changed the bulbs no luck they still only work on high beams checked fuses they looked good is there anything else I can check?
View 2 Replies
After spending weeks ordering parts and doing research on this issue all my attempts have not solved the issue. To reiterate the issue, the high beams work, and the low beams do not. Thus far I have attempted the following without the desired result-
1. Changed the headlights out just in case both bulbs burnt at once.
2. Changed the blinker stalk in hopes of a faulty switch.
3. Changed the headlight switch to a brand new OEM Euro style switch.
4. Checked all fuses (did this first actually).
View 6 Replies
The other night on my way home, I flipped on the high beams and the low beams didn't shut off. Flash to pass still works, and pushing in on the end of the stem turns the low beams off as well.
Having the column switch apart, is it possible this could be fixed without having to pull the steering wheel? Or, am I better off just spending the hundred dollars of so and putting in a new part?
View 13 Replies
[URL] ... Looking for info on my 99 Ranger.
Here's what happened,I have an electric plow I hook to my Ranger every year with no problems,except this year. The day after hook-up my wife noticed no high beams, don't know if the two are related but I did nothing but connect the plow wires already in place. Anyway I proceeded to look for a fix, fuses first, replaced both headlights next, blinker/high beam/wiper lever-still no fix and to boot my truck doesn't ding when keys in ignition, four wheel switch doesn't work, & wipers don't work.
View 10 Replies
I have a 99 Ranger w/3.0. It idles about 1500 rpm cold,and 1200 warm. Here are the things that I have tried.
1.Checked ALL vacumn hoses/lines
2.Changed Air idle control sensor
3.Throttle position sensor
4.removed and completely cleaned throttle plate in throttle body.
5. removed top of intake manifold and checked for cracks and/or leaky gasket.
Nothing seems to change. Could it be a faulty ecm?
View 6 Replies
85 ranger 2.3 fuel injected misses at high acceleration. Fairly new plugs and wires, just replaced the timing belt, pretty new fuel pump in tank, new fuel pressure regulator and pcv. It idles well, starts up and drives pretty well until you get it in 4th and really bog it down. Could be timing issues but I'm pretty sure I did everything right when I put the belt in. What it could be? I know when the tank fuel pump went out, it did something similar for a while...
View 9 Replies
My 92 ranger, 2wd, 6 cyl, manual trans, is running at about 3500 rpm at idle. I was wondering what might be the cause, maybe something with the throttle or could the gauge be screwed up.
View 14 Replies
