In 4 x4 ( 2000 ford ranger 4.0 ) and drive for a while I can smell gear oil burning off the exhaust looks like it's coming out of the right cv shaft? Is there a seal that goes first That's bad?
View 6 RepliesI own a 1990 Ford Ranger, 2.3 EFI with an 8 Plug setup and 2WD. It uses a dual-coil system an not a distributor if that means anything here.
Okay, so for the last week I have been experiencing extremely high oil pressures. My gauge would read almost as high as the "H" mark. The smell of burning oil was heavy in the cab from the vents. I took it easy, made sure my oil level was good and I had enough oil, the truck drove rough, but drove decent.
Yesterday, I got done sliding in some mud (not crazy bouncing or anything, just sliding). I stopped at a stop sign, turned around and hit the gas, and the truck died. I thought there were other issues not related to oil, however I noticed that the oil gauge now read about an inch left of the "L"ow mark. If I turned the key, to the "ON" position, the gauge pushed the needle to above the left gauge itself pointing towards about the "8 oclock" area.
Now, my truck will not start. It cranks and cranks and cranks with no start. I called a bunch of mechanics and none of them knew what I should do. AutoZone did not know what do, no one did. Some people said that the oil pump itself had gone out and that would cause the truck not to start and would cause gauge issue. Others said that it might be as small as the Oil Pressure Switch. Firstly, I bought a new Pressure Switch. Have not installed it because I cannot find the damn thing.
Where the switch OFFICIALLY is. I have read on Google that it is on the passenger side, at the rear end of the cylinder head. Other posts say it is by the oil filter...
PICTURES:
Without the key in the ignition:
With the key in the ignition, in the "ON" position:
I'm having some issues with my 99 ranger. It all started on my way to work one afternoon. Going down the road I started to smell some type of electrical burning smell. I looked at my instrument cluster and seen a trail of smoke come up between the steering wheel and ins cluster from under and gear selector covers. After that the O/D off light started flashing and downshifting hard. My pwr windows and dome light also quit working. Checked fuse #26 and all my fuses before going into work that afternoon, all of them were good and none blown. After shift was over that night going home I needed to use the wipers and they wouldn't work either. Also noticed then that my speedo, odometer and trip odometer not working. I've pulled my dash and steering covers off trying to find or see anything but nothing yet.
View 14 RepliesMy 2000 Ranger (4.0L, V6, manual tranny) is acting weird in first and second gears as well as idle. I hear a ticking and then the engine revs. At idle, I see the tach needle move a little. While driving, the truck jerks. It's a smooth ride once I move into third gear.
View 14 Replies2000 Ranger 4R44e transmission.Hard shift from 2-3 gear and when i run about 35-40 mph and brake then acelerate it downshifts hard . Whats wrong with it?
View 14 Replies2000 ranger 2.5 245000 miles. code po171 and idle problem has come back. Replace ICV, EGR, MAF, PVC, check fuel pres, air cleaner, plugs, wires, O2, check for vac leaks, Intermittently coasting at 20mph out of gear (stick shift) engine revs to 2500 rpm and holds until i brake to a stop then it idles down. So I disconnect the ICV and it runs perfect. (its a new ICV) something is telling the ICV to open up. a month ago it did the same thing when i replaced the EGR the idle problem cleared up so I thought that was it.
There is a relationship between the truck speed and the engine speed but how does the engine speed know the truck is moving when its out of gear. It work perfect for a month all of a sudden it starts this problem again. I am thinking of taking it to the ford dealer for a diagnostic test but I don't know how specific they can get on whats wrong I don't what to them to just say "oh you have a vac leak" . . . I know a 171 could be vac leak but the problem is so dramatic and off again on again it seems more like a part problem then a vac hose is either leaking or not.
I purchased a 1990 Ranger 4x4 with a v6 from auction. Took it to local shop to have them check it for me. Found out that it has a 3.0 in it and mechanic believes it is from a taurus. Truck actually runs extremely well. Has a few codes due to the ECM is for an automatic trans. Now the problem. I was on the highway-in 5th gear. Terrible noise the nothing. When I got it pulled over. The drive shaft was hanging from the rear end. It had been twisted like a straw. The transmission side had the yoke only, and the tail housing was cracked. It rolls and the drive shaft at the rear end turns. I figured the trans locked up. I don't know what trans to look for---is a 90 2.9 5 speed the same on a 3.0 ??
View 6 RepliesI replaced the seal the other day on my ranger because I noticed my fluid disappearing. Went ahead and changed the filter and fluid as well. Flushed the system, and I go back to my truck tonight and there's a huge puddle of trans fluid. And the output shaft seal is once again, up against the drive shaft. I've spent like $150 on trans fluid since Friday, and $1000+ to get the truck running again last month, so pardon me if I get edgy about her.
99 2.5 auto. I changed the trans pan gasket too. No leaks from it.
I am driving a 95 ranger xlt extended cab with a 3.0 two wheel drive with an automatic transmission. the two piece drive shaft with the carrier bearing went bad at the bearing. i separate the u-joint just after the bearing and was going to remove the nut holding the bearing housing together but cannot get the nut off. now i'm also finding out that i need a bearing puller to remove the damaged bearing from the 1st drive shaft.
Its turning into something i may not be able to finish. i saw on line an idea where a guy replaced the 2 piece shaft with a one piece. he states that a 1 piece drive shaft, 1998 or newer would work and no need for this bearing. you have to remove the cross member. it sound easier than what i'm trying to do. i looked at some old posts and galleries but did not see an article. here is a link to his website: How-To: Swapping a 2-Piece Drive Shaft for a 1-Piece in a 1983-1997 Ford Ranger
I'm replacing my clutch components in my 89 Ranger with an M5OD transmission. While I'm doing it I'm going to replace the input shaft seal on the transmission. I'm looking for the torque specs for the housing that holds the seal.
Also, should there be any play on the input shaft? My transmission has never made any noise but I noticed some slight play in the shaft.
I spent the day with a buddy working on his 91 ranger 4 cylinder 2WD truck because the clutch master cylinder shaft that connects to the pedal bent. We took the old part out and replaced it, but now we are having problems with the little pin that holds the line from the slave cylinder to the master cylinder in place. For some reason, even though the line is securely in position and wont budge with the pin in, it still leaks so we are unable to bleed the clutch.
I have looked all around the internet, including this site and wasn't able to come up with any explanation as to why the line is leaking, perhaps it is because the line isn't pushed in far enough, but like I said, it is securely in place and I wasn't able to push it in farther before forcing the pin into place. My buddy and I spent about 9 hours working on his truck today, including probably 3 or 4 just on trying to stop the leak.
I just bought a 5speed manual 2004 ford ranger 4x4 and when shifting usually upshiffter 1-2-3 I get a mi8ld clunk when I looked underneath I grabbed and can move the from drive shaft clockwise about 1/4 inch is this normal and if not how do I fix this?
View 3 RepliesThis morning the passenger side wiper on my 89 Ranger stopped working. I heard a clunk noise and it stopped but driver side still works. What should I check first? I'm guessing a shaft came off but don't know where it is located.
View 14 RepliesI noticed a strange vibration in the 83 Ranger I own, it has the 2.3 and a 4 speed. When getting up to speed around 35MPH it would start vibrating, and the speedometer needle would bounce around and read slower than it was actually moving. This would start in 3rd gear, and continue thru 4th unless I let off the gas while it was in gear, then it stopped and worked normally. I put a grease seal in the tail section when I first got the truck, and when I pulled the driveshaft again today the seal was mangled and bent, plus there are metal particles around the main shaft where the seal goes. I figure the tail shaft bearing is shot, and I also found damage to the yolk with the U-joint, the shaft has a worn spot about 1/3rd the way around.
View 2 RepliesToday I took the bed off of my 99 ranger. I was sitting on the cab looking down at the rear axle noticed the drive shaft was not entering the rear diff perfectly straight. As I looked further into it, I noticed the distance between the rear spring on the passenger side tire, is noticeably different. To visualize it, the wheel, at the bumper side of the axle, has a shorter distance between it and the leafs than the cab side. Not massive, but a few inches, and it's noticeable now that I can stand over it. I'm beginning to be very annoyed by this truck and it's previous owners, whom I take it , scammed my brother quite well with a $5k tag for a truck with so much not right with it. It's about to become my yard art for awhile.
View 8 RepliesI have a '90 Bronco II w/ the 2.9L V6 with a head/gasket issue leak. Its burning oil/coolant in #3 cylinder drivers side. I would ask this in the B2 section, but the Ranger section seems to have alot more activity.
I'm wondering what my options are. I'd like to replace the head with a better aftermarket design if possible. I've seen World Products mentioned as a good replacement, but they are no longer making them anymore. Nearest I cant tell, that leaves King and Odessa aka Clearwater heads. On the 'bay Odessa doesn't have the greatest feedback. King looks like a good product, but kinda spendy also. Short of those two, re-man is the only other option.
The casting # on my head doesn't line up either, is the 86TM the better Euro head for the Merkur?
If I keep this engine, w/o doing a 4.0L conversion, I'm tempted to replace both cylinder heads because of the amount of work to tear it down to that point.
This motor has had some valve ticking also, but I've read it can be injectors instead. What should I do? This will only be used as an off highway light trail rig.
So I just got done with my first 2 problems of the month with this truck last week. Front end and emissions along with spark plugs. Now, 4 days later this morning, I'm driving the truck trying enjoy the investment, and the AC compressor starts seizing up and burning the clutch. Unrelated but also worth noting, about an hour later the brake pedal gets real soft and the brakes get really sloppy at stopping the truck. The truck also stalled (auto trans) crossing a highway, luckily it was 5am and no traffic was coming.
I'm at $6k invested on a truck with 116,000 miles, and I've only put 6,000 on it. The repairs don't stop, and I've got many more ahead. Like rear suspension, axle, trans, and radiator fluids, and paint, to name a few. Any suggestions on fixing the AC before I drive this truck into a lake?
I have 2011 Elantra at ~20,000 mile, and strange things started happening since last year...and it kinda blew up today.
My dashboard has been flickering randomly for a while, as in everything goes dark and turns up again in the middle of driving.
And today it turned off and turned on (as it usually does), and the dashboard seemed broken; speedometer stuck at 0 mph, rpm meter stuck at 0, all warning lights turned on, gas meter going up and down and stuff.
Fortunately enough I was close to home so I drove it back home, and my gear shift was stuck at neutral (I could switch b/w N and D).
So I took out the shift lock release? thing and managed to put the gear to P and pull my key out. I stepped out of my car and I smelled something burning...not a very good sign. What should I do? Well I think I need to take it to dealership tomorrow but I'm not sure if it'll be safe to drive...
So i am going to drive to school and going up the hill on my street to turn on the road and i give the car some power as i usually flore it up the hill but suddenly the check engine light pops up and the car doesn't want to go. My foot was all the way down on the gas and i was getting like 3-4 rpm and the car wouldn't even get up to 30mph. so i go around the block trying new things turn off the car and restart it and the same happens so i go back home and park it in my driveway and i turn the car off and get out. I smell something burning from the car so i pop the hood and check underneath the car but no smoke just and intense burning smell. I don't know what is wrong the car just had the recalls done a week ago and this is the first thing that ever happened like this to the car. Has this ever happened to you? What do you think is wrong with the car?
View 4 RepliesI've got a 2000 Subaru outback with 170k miles on it. I recently pulled a code for a bad line pressure solenoid and replaced it. About 500 miles later the oil temp sensor light started flashing so I turned the car off and when I turned the car back on it wasn't flashing and hasn't come on since. No CEL. I'm now about 2k miles after changing the line pressure solenoid and now whenever I drive over 10 or so miles my car smells like the clutch is burning. He idle is a little rough, i.e. it vibrates a little more than usual and the car is a little slow to respond when I gas it.
View 19 RepliesMy 2003 Nissan Sentra was doing fine a few days ago until I started up a very steep hill and went into 1st gear. There was a burning smell for about 2 blocks so I shifted to 2nd gear. The smell went away. When I was in 1st gear it did not sound or feel like I was trying to go too fast for the gear. I just smelled the burning. Same hill in 2nd, no smell. How much should I worry?
View 2 Replies