Ford Ranger / B-Series :: 2000 - Battery Not Charging / Alternators Dead Immediately After Install
Sep 18, 2014
I was messing with the battery in my 200 Ford Ranger the other day and must of arc something. I know this because after plugging my battery back up my radio fuse was blown and my alternator was killed. I replaces the radio fuse, that works now, and got a new remanufacted alternator (tested mine at Advance it was dead). I installed it and nothing changed. The battery still wasn't charging. I know the battery is good because I tested it at Advance Auto. I took the alternator back and the shop replaced it with another remanufacted one. Same thing, installed it and the battery doesn't charge.
This time I took the alt back off and had it tested at Advance. The alt was dead. So I don't know if the part store gave me TWO bad alternators or if my truck is killing them. I find it hard to believe it could kill them immediately but my automotive knowledge is not that vast. I took the second (third counting my original) dead alternator back and they gave me a brand new one no extra charge. So I don't want to put a brand new alt in my truck and it kill this one too because I doubt they will give me a fourth one. What is going on? Could it just be as simple as I got two bad eggs?
View 9 Replies
Advertisement
Is there a fusible link from the alternator to the battery? The new alternator that I put on and got tested is not charging the battery. Was wondering if it could be a fusible link but I couldn't find it. Where it is located on a 2000 ranger?
Also, I put a DC volt meter on the negative side of the battery and the positive side of the CHARGING wire that would be connected to the alternator and got the same reading as if I put the meter on the positive of the battery.
Does this mean the fusible link is good?
View 14 Replies
I just finished putting in aftermarket A/C in the 2004 Ranger my dad gave my son. It's a 2.3L, STD transmission. It was running GREAT before the project started. I installed new battery as part of the project. When I started it back up it ran for 2 or 3 seconds then died. I now cranks, but does not fire at all.
I have tried one of the key reprogramming sequences (turn key to "ON" 8 times) with no success. Would it crank at all if it were a key security issue? Is there anything I need to reset anywhere else, like in the air intake system?
It's either not getting spark or not getting air. The fact that it ran for a couple of seconds has me confused. Would it run at ALL if there was a key security problem?
I had to remove and reinstall the air filter housing and ducting. Is there anything else I need to do to with the air intake system?
View 3 Replies
every few days, the battery stops charging and dies.... tested the alternator, and that provides a charge...tested the battery, and that takes a charge... the car runs off the battery or alternator...tested and replaced all wires between alternator and battery... cannot figure out what is wrong.
View 9 Replies
So I have a very confusing problem. In my 92 Chevy Astro the battery occasionally stops charging runs down and dies while I am driving and will not restart via jump but must be fully charged. This first happened a couple months and several thousand miles ago but has occurred 3 times in the last two weeks. Both the battery and the alternator have checked out good, and the alternator belt is tight as a drum. What could this possibly be?
View 6 Replies
Just hoping that there is something common that causes this problem. This thing can idle just as smooth as you could want one to and the next time it will have a dead miss, and the miss is not consistent. It may miss like three hits then be ok a little then miss a little. There is no CE light or codes. Again just hoping there is something common.
View 2 Replies
I recently bought a 1969 chevy c10 pickup. I have been having problems with the electrical system, the battery consistently going dead despite a new battery and alternator installed by the previous owner. Is there a step-by-step for diagnosis of this problem?
View 3 Replies
2000 Ranger 2.5L. Recently driving up and down road to work about a half hour in to drive the battery light will flicker especially if under a load (AC on, lights on)etc... Assuming it is the alternator/voltage regulator getting ready to FAIL. Plan on replacing alternator this weekend? What to do or check something other than replace the alternator?
View 5 Replies
My dad's Gen III has been sitting garaged for almost a year now, and of course the 12 volt battery is dead. Firstly, it's sitting in a one car garage, and secondly I have a Gen II so a straight jump isn't possible. I have a trickle charger that should be able to bring the 12 volt back up in 15-19 hours, but here's my question:
Maybe I'm being lazy, but I'd rather not deal with climbing in the back to release the hatch and running an extension cord so I can get the charger close enough to hook straight up to the battery..
View 19 Replies
Got a 1986 Ranger 2.3 EFI 5 speed that I have owned since it was almost new and will never let it go. 290,000 mls and still running strong "except". Noticed the last couple of months that when I start it cold it fires right off. If I start it hot it always takes 3 tries and always goes on the third try except....on occasion it will not start at all. It is random and after I let it cool a bit (about 30 min) it will start. Over the years I have replace many of the fuel system components (fuel tank pump, high press. pump, inline filter and canister filter, fuel press regulator) but wondering what else might be the problem.
I put a pressure tester on it the other day and when I selected the key to start the pump would spool up to build pressure and shut off. The press gauge would register that but the pressure would immediately go back to zero. After start up it would hold a constant 30psi at all rpm,s. Shut the engine off and pressure drops right down to zero. Shouldn't the system hold pressure for at least a while after shut down? Could this be the problem with my sluggish starts? What would be the normal fuel pressure? Can't seem to find it in my Haynes manual. Once running it runs great.
View 6 Replies
2001 ranger with 4.0, alternator failed and new alternator is also not charging, showing very little output. i've installed 2 new ones with no fix. the regulator is in the alternator, correct? I'm stumped and not sure where to go with this.
View 14 Replies
My tires are 245/75/16, is there any benefit in installing smaller 16" tires?, I'm 5'5", I can still get in, but I would like to have it a little bit lower, will that affect mileage, speed etc.? would that even make a difference? if it possible how small can I go without affecting performance?
View 13 Replies
1996' Ranger with 183,000 miles. 2.3 cyl., Automatic, XLT
When I am driving and get to the 35 to 60 mph range, my trucks transmission wants to upshift, then immediately downshift to the gear it just left. It goes back and forth like this till I get where I am going, or after about 10 miles it will stop doing it. I checked the transmission fluid, and it is full and still pink.
I took it to Advanced Auto, and it blew a code of ECL Bank 1 I believe. I looked around the 'net and I think it came out to be the front O2 sensor may be bad/going bad.
Last week while it was warm enough I was driving with the rear window open, and noticed the faint smell of Rotten Eggs (this has been the only time though). Today I drove about 50 miles and basically used a quarter of a tank of gas. I am wondering if the catalytic convertor may also be going bad?
View 9 Replies
I just rebuilt the carb on the truck, it has the 2.8L, and when I went go go start it, it cranked for awhile until fuel filled the bowl, then it started and revved up high, I shut it off immediately and it turns out the throttle linkage was binding for some reason, I fixed that but now it wont restart.
I was cranking it for a while and gas started spewing out of the top, so I took the top of the carb off and reset the float height and now it doesn't spew gas.
I pulled the plugs and checked for spark and it's a really bright blue spark. I'm thinking it's just flooded, lots of gas on the plugs? I'm just waiting for it to clear out now and trying to brain storm what could be wrong.
View 14 Replies
This 2005 LeSabre with a 3.8 v-6 ran fine but had a marginal battery. Then the key got left on overnight leaving the battery totally dead. After jumping the battery and letting it charge, the engine cranked fine but refused to start. Haven't had a chance to check for fuel or spark. Why would a dead battery trigger this no start condition?
View 2 Replies
While driving at any speed my temp gauge and oil pressure gauge spike well above "H" and stay there. The red battery light sometimes flickers too. The Battery gauge is low. I replaced the terminal to then negative battery cable because It was loose. I have also replaces the alternator. I had the battery checked and it was good, it just at 45% charge. That's why I replaced the alternator. After I did that, It seemed to have fixed the issue. But after 3 days, it has come back again. Now this morning on the way to work, driving down the freeway, my speedometer jumped to 85 MPH and there was a squealing like noise coming from the engine. I am not sure if the two are related issues.
View 10 Replies
My 99 Ranger charges intermittently. Sometimes it is just fine, sometimes the voltmeter drops and the light comes on. Might go a mile, might go all day without an issue. Alternator was replaced 2 weeks ago. Where to look? I haven't ruled out the possibility of a bad "new" alternator, but I haven't been able to get it to act up when I actually have time to start diagnosing it. Is there a relay somewhere that could be causing this?
View 14 Replies
93 Ranger, 4.0 liter, 4WD.....
Putting in a new clutch and clutch release bearing, and am wondering if I need to put the retaining ring in that came with the new clutch release bearing? When I took off the old release bearing, a ring did come off from somewhere, but I did not see where it was because it was so dirty.
The reason I ask is because my Haynes manual did not even mention a ring, so I was surprised to see one come off. And my manual does not say to reinstall the ring when installing the release bearing. I did get a newer Haynes manual at the library and looked through a bunch of Chilton, etc manuals.
The newer Haynes manual says to remove the retaining ring on 97 and newer models, but says nothing about putting it back in when reinstalling. So, I am not certain if I need to put a new retaining ring in with the new release bearing.
View 7 Replies
I placed my Corvette with a consignment seller this summer. When he had no action, I took the car back but...battery dead. Fully recharged it, car started immediately (first time in 2-months) but then died and will not restart. My ace mechanic has replaced fuel pump, distributer, but no fire. Indication is weak/no signal at he injectors. Could this be residual Theft Prevention system? I had that fail years ago and I pulled the module and the car has done fine for 4-years, until now.
View 6 Replies
I just picked up a 1984 ford ranger long box 2 wheel drive w/ 2.0 l and carburetor for our daughter whom is just 15. it has a whopping 19,000 actual on it! It was my wife's grandma's farm truck - ordered it new from dear born. Any way, fuel gauge is pegged at empty and they had a new float assy put in about 5 years ago, but it is dead now, it doesn't appear that this sender is avail any longer. What part might fit in there and or what do i have to do to maintain the original gauge in the cluster but have a working sender to talk to it? is there another unit that goes in the tank that i can modify the signal out to read right with the built in gauge? There can't be too many different ones out there is there?
View 8 Replies
Wonder if its dry driveshaft slip splines? Only happens when leaving a dead stop under hard acceleration. Hard to describe sound, but seems to be coming from behind me, almost sounds like 2 broken pieces of steel snapping past each other. frame is o.k., leaf springs are o.k. , doesn't do it when shifting between gears or if I gently take off from a stop. I don't think there's a grease fitting for the driveshaft where the splines are (where the 2 piece shaft takes up slack for being loaded or unloaded) may have to take that apart once the weather breaks and see what i find. my 1st ranger never had this issue after 200K miles. this truck is now at 145K but its almost 20 years old. I've read somewhere before about pulling the shaft apart & greasing the splines up. does this sound like a possibility for whats happening? not sure what else it could be.
View 3 Replies
