Ford Ranger / B-Series :: 2000 B3000 4x4 - No Shift - Dreaded Six Lights Flashing?
Mar 26, 2015
I have spent two days searching for a fix to a problem like mine on my truck and I haven't quite found it. Sooo, here it is. I have a 2000 Mazda B3000 4x4. I'm getting the dreaded six lights flashing. I can hear the clicking under the dash as it attempts to engage the 4WD. I have checked the Motor at the T/C and no power. What feeds voltage to the motor its self? and is there any other thing I can check B-4 having it scanned? oh and it is a manual tranny.
View 4 Replies
Advertisement
My mazda b 3000 shut off while at a red light i t turned over initially 3-4 times now nothing. changed EGR, ECM, CRANKSHAFT AND CAM SHAFT SENSOR three weeks ago. brand new battery, took alternator in and it was bad so i replaced. theft light is blinking rapidly?
View 2 Replies
2001 M B3000 v6 my sons truck w 122k. He is overseas and I took it to deliver a CB750 bike to my brother in law... 4oo miles away from my place.
In the middle of nowhere TX it developed a bad miss or knock, almost a shudder in the 2 to 3 k rpm range. Idles ok just below 1k runs fine at 70 mph as long as the rpm is near or over 3k.
Not sure I want to turn around and drive back the 400 with it running like crap. I will take it to Autozone and pull codes tomorrow a.m. but what should I expect?
View 9 Replies
I have a 99 Ranger, 3.0 xlt 2WD Automatic 5r55e(???) tranny (i know its the 5). I have the o/d off light flashing. It comes on when fluid gets to op temp. When on it shifts hard into 2nd and hard when it downshifts. No slipping. I have had the truck in the tranny shop for 3 weeks, owner said he re built valve body gasket (didnt work) tried 3 diff used tranny's (didn't work) or so he says. He said it needs to be rebuilt.
I have searched up and down for what it could be, there is so much out there, it only confused me more. If i have to rebuild i will, i think the tranny shop was pulling my leg (for more reasons than mentioned). I have a check engine light on nothing to do with tranny...there is a tranny code, he would not tell me but i will have it checked. Been told could be throttle position sensorl, speed sensor cracked case and a million other things. I have some mechanical abilities, (not too much w/ tranny's) but i can change a few simple sensors.
View 1 Replies
All my guages move (needle moves to the right) once I turn on my head lights. Indicating higher egine temp and higer oil pressure. What cause be causing this?
View 4 Replies
I have a 99 Mazda b3000 v6 that has recently started to stall whenever in idle. Check engine light is on and the following codes popped up (P0176, P0135,P0141, and P0155). I'm sure one of these codes has to be related to the problem but I am clueless when it comes to troubleshooting. Also it started stalling after I filled up the tank. Not sure if that has anything to do with it, check engine light was already on before that.
View 2 Replies
The facts: 98 rangers 4.0 4x4 177k
The issue: does the dreaded shudder start, check engine light is on saying lean bank 1 bank 2.
Fixes so far: have replaced every gasket intake base up, a lot of new sensors on the intake. All 3 of the 02 sensors new. Have not touched egr. Thoroughly inspected plenum and intake hose for cracks, no Pitts in the intake.
It's a NEBRASKA truck with zero rust. Thought maybe fuel pump might cause all these issues, however, the turn the key twice trick before starting makes no difference, and I can hear the pump turn on each time I turn the key.
View 13 Replies
My buddy's 1998 4.0L Ranger caught fire from the dreaded brake switch shorting on the master cylinder. In his defense, he's only owned the truck less than a week and had no clue of the recall. The damage is mainly to the wire harnesses on the driver's side.
Rebuild the wiring. What other years of the Rangers I can pull the wiring harnesses from? Or if the 3.0 harness will work?
View 10 Replies
Went from right around 18 to 14-15 last 2 tanks. No codes, drives absolutely normal. I have had my 4x4 lights flashing, but the 4x4 has never worked (suspect its a combination of the transfer case motor and the pulse vacuum hubs). Used to flash like this when I would try the 4x4 switch and would take a while to "get back to where it was happy". Recently I have not messed with the switch or anything else.
View 14 Replies
2000 ranger 3.0 auto 4wd hard to shift. Are the cables known to stretch?
View 6 Replies
What would cause my 4x4 high and 4x4 low lights to flash intermediately together on cold mornings while driving? It won't switch into 4x4 when it does this either. When it sits and warms up later in the morning all works as should. It doesn't do it all the time but when it does its annoying not to mention it's sucks when I need 4x4.
View 1 Replies
Sold my mazda and got a nice 2000 2wd Ranger XLT with a 3.0L. Today the wife I and took it to town, 10 miles on the highway there, a couple in town and 10 back, didn't notice anything unusual. However I haven't this truck long so I'm not sure what is usual.
Parked it for a few hours and when went out to change the front turn signals to LED I noticed the ABS light was on when I drove it into the garage...
I checked fluid, connections and fuses, no change.I go ahead and swapped the bulbs while letting things simmer, I've had so many of these Fords sometimes the easy fix comes to me.
I backed it out and took it down the road, right away I noticed my speedometer wasn't working, so I let off the gas, when I re-applied the pedal I got nothing, like it was in neutral.
I downshifted to second and got her down and turned around as the O/D started flashing... (so glad because I would have hated walking back), then pulled her back in the garage to check transmission fluid and recheck fuses, including the ones I forgot earlier under the hood. I added a 1/4 qt of fluid then tried a road test again, this time there was a real long pause before it upshifted hard and the CEL came on.
I pulled the codes with my scangauge and got:
P0500
P2120
P0028
And decided I better look some things up and consult the gurus here before I do anymore damage tonight. I'm guessing that I'm looking at a tranny replacement possibly, but with the ABS light and speedometer failure I'm not 100% sure what is going on here...
View 12 Replies
2000 Ranger 4R44e transmission.Hard shift from 2-3 gear and when i run about 35-40 mph and brake then acelerate it downshifts hard . Whats wrong with it?
View 14 Replies
I bought a 2000 Ranger 4x4 3.0L auto today from the neighbor guy sight unseen with a "bad tranny" for $400. I'm very unfamiliar with the Ranger family, but long story short:
When moving the shift lever, the trans doesn't engage. It needs to be engaged from underneath. Do the cables tend to stretch, or break? I can't find any adjustment on it anywhere.
View 5 Replies
I have a 2000 ford ranger 2.5 automatic. runs fine except when stopping at lights and intersections it stalls. I have changed the MAF, TPS and hasn't made a difference.Truck only has 64,000 miles. What to look at next. no codes...
View 14 Replies
When it rains my "door ajar" light comes on and the overhead lights won't turn off. that's the common problem. i've read many threads where it says to spray liberally with WD40. i intend to do that but the plot thickens.
Usually, after a few dry days, the light goes off and everything returns to normal. Not so any more. the newest episode entails the light staying on for two weeks of good warm, dry weather. naturally i always take the bulbs out. Now, its somewhat sporadic but.... I'll try to explain since I'm still trying to wrap my mind around it.
1. light stays on, dome lights won't go off.
2. tried dome lights couple of times, still wouldn't go off
3. finally, inserted dome lights and they wouldn't come on (except when manually switched on) however the door ajar switch was still on.
4. EXCEPT when i opened the passenger door the domes came on but wouldn't go off so i took the bulbs out again.
5. that's where i am now.
Not positive but I'm thinking since the new wrinkle in established expectations that I'll probably end up replacing the driver's switch. Before I tear up the door panel i need some hints concerning removal. the door has power windows and locks (which i need new actuators but that's a different story). Is there anything I need to watch out for?
View 3 Replies
I have a 98 Ranger, 4.0 automatic 4x4...I just replaced the upper and lower intake gaskets and after fumbling with the pug wires to finally get them in the right order, I suddenly find my OD light flashing off and on, and the tranny slamming into second, and once in top gear can feel the OD popping in and out? From my reading here it looks like a pretty common problem, but the solution isn't as clear...
The vehicle set for about 3 months while I healed up from a injury, and and was working just fine when I parked it...due to the blown lower intake gasket. I am thinking I have a vacuum line not connected or wrongly connected...or some kind of over looked item, but I can't spot anything...should I get a code reader and go from there...
View 14 Replies
I have a 2003 Ford Ranger, recently I had the heater core fail. One thing that happened during the heater core starting to leak is the "THEFT" light came on brighter than normal and no longer flashes when the truck is off. Also when the theft light started acting up the O/D OFF light came on and would not shut off. If I pushed the O/D off button the Theft light will go out and then come back on after the button is released.
After the heater core was replaced the lights stayed on as described above. Every once in a while the O/D off light would stay off but then come on later. No really problem besides the lights and O/D off button not working. Now today the O/D off light started flashing and the truck kept shifting in and out of O/D.
I'm leaning towards a speed sensor issue. I'm going to check and see if there is any codes tonight and will post my results. One other thing that happen with the heater core leaking is the "CHECK ENGINE" light came on because the O2 sensor was shorted out. Have the O2 sensor now and plan on replacing it while I trouble shoot the erratic shifting in and out of O/D.
View 14 Replies
Been awhile since I've been able to post but I've got a serious issue with my 2006 Ranger XLT 4L V6. So last night about 2 miles from home my check engine light started flashing like it was a at a rave and my engine wasn't acting right, also had the STRONG odor of raw gas, no other lights from the dash, no fluids leaking, oil was good n nothing in radiator but coolant. Was able to baby it to my current home but all my tools are in storage so had to wait to get my ODB scanner to see what's up. Scan came back as 'cylinder #3 misfire' & 'O2 sensor reading rich'.
Go cylinder #3 spark plug out and it were fouled bad. Got ride to the store and got a whole new set. Got back n got'em changed and fired ut up, idle still rough and check engine started flashing again and white cloud coming from exhaust pipe and STRONG odor of gas. Check and now have 'multiple missfire', 'cylinder #2 misfire' and 'cylinder #3 misfire'.
Shut it down go and double check ALL spark plug wires are connected and TRY to start, get about a turn n a half then starter spin. Try again and the engine won't even turn over. "Great I've seized the engine!" Was able to put a socket on the crankshaft pully and manually turn the engine over "whew didn't seize the engine", did this a couple of times and tried to start, was rough but eventually it fired up, still idling rough and again check engine light flashing, while it was running I pulled one plug wire at a time from the coilpack to see/feel the lighting and there was spark for the 3 I pulled, didn't affect engine idle.
Run codes and 'cylinder #3 misfire', so now that the engine is was warmed up I pulled out my ohm meter and started checking wire resistance. Cylinders #1, #2 were at .012, #3 was .011 and #5 was .009.
I've figured that the raw gas is due to cylinder #3 not burning and just pushing gas into the exhaust. So to the brass tacks, do I invest in a new set of wires? Or could it be the injector being stuck open and just flooding the cylinder? No when I originally pulled the #3 plug fuel did not spill out. Haven't pulled #3 again due to it being May in Arizona and had to take a break. I'm going on the assumption that the engine wouldn't start after a short run do to "hydraulic lock in cylinder #3", my manually turning the engine over cleared this and allowed the engine to start.
View 9 Replies
ive been experiancing an issue with my trucks shifting. it shifts smoothly but doesnt like shift into 5th, as im driving it stays in 4th longer than necessary. my thought was that it was tied to a shift sensor, what do you think?
View 5 Replies
My 2002 Ford Airbag light is flashing 46. I believe this is the Drivers side crash senor. I am repairing the left front fender and left front wheel suspension. I have replaced the two air bags and airbag control module. Where is the left front crash sensor?
View 13 Replies
