Ford Ranger / B-Series :: 1999 - Trans Slipping In 1st And 2nd Gear?
Jan 22, 2017
I have a 99 Ranger 3.0L automatic, ext cab, 2 wheel drive. Door sticker show code "T" which I looked up as the 4R44E. The trans seems to be slipping in 1st and 2nd. Thought it was "reared shudder", from a "limited slip" differential but mine is not limited slip. just the regular 8.8 with 373 gears.
Wanting to know what if any options I have for buying a new / rebuilt tranny? I've seen where depending upon the year and motor, Ranger can have 4r44e, 4r55e, 5r55e, etc.
View 3 Replies
Advertisement
i have a 1999 mazda troy lee b3000. The truck has a 3.0 flex fuel and 4r44e and when you go to drive it. turn the key engine fires up but the trans won't shift into gear. Here is the back story.Bought the truck brand new in 99 I'm the original owner it was a daily driver up until 2 years ago. the truck has over 300k miles and still ran great but the camshaft was starting to go. I was gona replace the cam but came across a killer deal on a new engine. picked up another 3.0 flex fuel with 50k miles. drove the truck into my garage removed the old engine installed the new engine. got in the truck turned the key and the new engine roared to life.
I went to put the truck into gear so i could get it out of the garage and go for a test drive and nothing. went to put it in drive and again nothing. no matter what gear its put in it doesn't move at this point i was confused and decided to quit for the night. That was in 2011 its now 2013 the truck has just sat there sense then. I've tried anything and everything even went as far as swapping transmissions and computers with no luck. I took the trans apart I don't know how many times can't find anything wrong with it.
View 4 Replies
I have a 98 XLT 4.0, auto trans with 109K miles and when it's really hot outside and it's been driven when I start back up and put it into drive it sometimes takes a while to go into gear. A friend says the transmission fluid doesn't look too good and it smells. Obviously I have a transmission problem but my question is would changing the fluid do any good at all? Since the tranny is bad what harm could it do? The fluid was never changed previously.
View 6 Replies
I have a 99 ranger 4x4 4.0 V6 with 200K miles..I just had the slave cylinder replaced and bled however, it is still hard to get into gear and when at a stop light with the clutch pedal pushed in all the way the truck tries to move forward as if its in gear. I took it back to the shop and the mechanic says that the hydraulic system is working as it should and the problem could only be the pilot bushing failing and causing the trans to partially engage. The clutch and previous slave cyl only had 25K before the slave cyl failed and started leaking!!
View 12 Replies
1996 4x4, manual trans. Wants to kick out of first, and when shifting into 3rd I have no gear. Doesnt grind, just goes in as though it were neutral.
View 4 Replies
So my new/old 2004 has another issue. Parked at the grocery store tonight on a very slight incline backwards. Put the Ranger in park (automatic shift) and before I could fully engage the parking brake it began to roll back with a clunk, clunk, clunk as if popping out of gear.
Need less to say I moved to another spot that was more level. Just an hour before I parked the same way on a steeper incline and did not get this. Now I need to watch this carefully until resolved. How to remedy this issue.
View 3 Replies
My clutch is weak and slips sometimes and I need to replace it. ,I have replaced the clutch disc in other trucks but never a Ranger.
1999 3.0, 5 speed stick, Extended cab....
View 11 Replies
So ever since I picked up the truck from getting the springs swapped out the tranny has started to slip more and more. It's about at the point now where it does it at the 1-2 and 2-3 gear change every time unless I give it a little throttle so it shifts harder. It's just the normal shifting pause and then the slight jerk when the next gear starts. Time to a new torque converter, or am I looking at getting my whole thing rebuilt? If it's the converter I can give that a shot myself but if I have to have it rebuilt it's going to have to wait until January or February.
View 14 Replies
Here's my transmission problem. 2007 f150 crew lariat 4x4 with a 5.4
When my driving conditions force me to cruise at the 28-30 MPH range my transmission often hunts for an upshift, like a slipping gear hunt then it hits in firm. It must be from 2nd to 3rd gear I'm thinking. It doesn't occur at all if i am accelerating through this gear or past this shift point. under normal acceleration through and past this speed or shift point it is as smooth as can be.
I often drive some flat but winding dirt roads out in a forest area near my deer camp and it seems this is where I settle into a speed of 28-30 mph for several miles at a time. This is where it happens, the transmission seems to begin to shift but seems to slip or hunt for that next gear then it hits in fairly firmly.
Truck has 83k on it....
View 4 Replies
I have a 1999 ford ranger 2.5L. When I turn the key to the ON position, right before the ignition turn, everything comes on like it's supposed too. However, if i try to change into reverse, the truck will start without me even touching the key. Also, if I start it using the key and try to go into reverse, the starter engages and makes the all to familiar grinding sound. I am completely stumped.
View 4 Replies
I just got a 99 2.5 rwd auto and it shakes when it's at idle in gear. I'm pretty sure its because the AC pulley is engaging drawing power. I was thinking about turning the idle screw up a blonde-one because when I hold the brake and give it slight gas it goes away.
View 3 Replies
I have a 1999 ford ranger 4x4 with automatic 5r55e and it had problems shifting smoothly into third gear. I changes the valve body gaskets and the (rooster comb) detent lever. Now it shifts very hard and has on first second and passing gear.
View 6 Replies
My M5OD in my 1999 Ranger 4x4 with 3.0 occasionally pops out of 3rd gear. I think it does it only under light throttle or coasting. Also some vibration, especially in 3rd gear. Once in a while the gears grind when shifting into third. Truck has 145,000 mostly highway miles. Frequent fluid changes with Redline D4ATF.
What could be the cause, bad synchros ? How hard is it to remove the transmission and make a repair for something like this, what kind of special tools, etc. I assume a transmission jack would be real useful, what else would I need other than the normal wrenches and sockets ? Is there a good shop manual recommended for doing this repair ?
View 4 Replies
I'm having trouble with my auto tranny again. it is a 4r44e and is in a 1999 3.0 flex 2wd extended cab. It will not pull in reverse, seems to be slipping bad, and it won't pull in forward gears unless you switch OD off. Then it seems to pull fine but still not in reverse. I haven't drove it very much to see on changing gears and such for fear of burning it up.
Fluid is still like new no codes showing just started out of the blue while my son was driving. All electrical is hooked up tight and no leaks fluid is little overfull but not much. I am going outside now to adjust intermediate band to spec. had trouble with overdrive that had everybody stumped if you remember and it was overdrive band adjustment so going that route first.
View 6 Replies
I have a 1996 Ford Ranger with 95k miles on it. Recently, my truck's automatic transmission has been slipping really bad. I'll be driving down my road and while going around a turn, the clutch feels like it randomly disengages, so when I press on the gas, it feels like I'm revving my truck in neutral, and then it will all of a sudden get back into gear, violently a lot of the time. However, once the truck is warmed up, the it runs perfectly and never slips. I've checked my oil multiple times and even changed the oil filter in the transmission. I am not sure if this has anything to do with it, but if I let my truck idle in park for a little bit, the RPMs will increase and if I shift in to reverse or drive while the RPMs are high, it'll do the same thing.
View 14 Replies
It does not like to stay in 5th gear, drops out to neutral. 2001 Accent Hatchback. 1.5l 5-speed
The other day it started slipping out of 5th gear on the expressway. Held good for the first 10 to 20 minutes. Afterwards I had to hold it in 5th for it to stay in gear. While holding I noticed it pushed on the shifter when applying throttle, and let up some when I let of the gas.
I inspected the pivots at the transmission. The forward / back bushing was not installed properly by the previous owner. I rigged it up better with a fender washer and cotterpin. It previously had just a pin and the bushing had expanded out. This removed the play from shifting I had previously noticed. It also halfway fixed the popping out of gear. It stays in gear a little longer, and when I put it back into 5th it stays there for a while most of the time.
I have not inspected the lubricant level yet. Where to check next?
View 10 Replies
1991 Ranger 4.0L A4LD... Its a 4x4. ext cab
What else will bolt up to this 4.0L? Could i put a 4R44E/4R55E tranny? Is there a good stick that bolts up?
View 5 Replies
2002 CAvalier 2.2 automatic with 123'000 miles. I was asked to look at this car for a slipping trans problem.
I drove the car about 3 miles and in 1st and Reverse it feels normal, even on a steep hill, but once it shifts into a higher gear the trans slips and you can go only about 15mph.It is shifting, because if you move the shifter into a lower gear while traveling....you can feel it downshift.
There is a code of P0502 Vehicle speed sensor. and there is no Trans fluid visible thru the filler cap on the trans top.
Previously someone else worked on this car for the slipping trans....changed some sensors....but couldn't fix the problem. The owners don't know what parts he replaced. He works for a Tire outfit and I've known him to lean towards used parts a lot.The previous mechanic convinced them that it needs a new Cluster. I presume he means instrument cluster.
I have a feeling that he just threw parts at it hoping that something would stick.
I presume that he replaced the VSS, and it didn't cure the problem.Come to think of it....the code could be from before the other persons work. I should have cleared the code and test drove it again.
I'm looking at dropping the pan, replacing the filter, refill the fluid, and replace the VSS
My questions: Could a instrument cluster have anything to do with the shifting problem.
Is the level of trans fluid supposed to be above the ledge under the filler cap, or is there a "full level" plug in the side of the trans. If he replaced the VSS with a new one....and the fluid level is good....whats my next step.
View 15 Replies
I have a 98 Ranger, 4.0 automatic 4x4...I just replaced the upper and lower intake gaskets and after fumbling with the pug wires to finally get them in the right order, I suddenly find my OD light flashing off and on, and the tranny slamming into second, and once in top gear can feel the OD popping in and out? From my reading here it looks like a pretty common problem, but the solution isn't as clear...
The vehicle set for about 3 months while I healed up from a injury, and and was working just fine when I parked it...due to the blown lower intake gasket. I am thinking I have a vacuum line not connected or wrongly connected...or some kind of over looked item, but I can't spot anything...should I get a code reader and go from there...
View 14 Replies
The problem I have is the truck won't move in o/d. If I put it in revers 1,and 2 it works. A little back ground. 4 years ago the trans went out of my 95 4.0 4x4, had it rebuilt so it has 0 miles on it. It got really cold that winter had lots of trouble getting the trans and torque converter lined up. motor went bad on me. A few months ago finally had some money to spend bought a 98 explorer sport with a 4.0 x code motor. the motor runs fine apart from an oil leak and an exhaust leak. the exhaust leak is no big deal I just haven't gotten the system tight yet.
View 8 Replies
02 ranger 4.0 v6 auto has 110000 miles on it. at highway speeds 65-70mph feels like it strugles to shift, truck will shake and bounce some. when this happens rpm's jump from about 2200 to 3000-3200 after a little bouncing rpms drop to normal. issue seems to be the worst going up hill but will happen every time i hit 65-70. Also the truck will not bounce or shake with the OD turned off and seems to run fine this way.
tranny fluid/ filter just replaced with no change. new plugs and wires
View 3 Replies
