My 1999 ford ranger, when started, shakes and then while i am driving. my check engine light is on and reads a #3 cylinder misfire. I have taken it somewhere to get it checked out and they can't figure out what is wrong with it. this problem only happens 50% of the time. I don't know what to do. Also just got a tune up.
View 14 RepliesMy problem is wih my 1996 Ford Ranger XLT 6Cyl. 4.0L 2WD Recntly it started shaking violently in the rear as I drive down the road any road. Mainly slow to about 50MPH or slower, it just starts to shake really hard and then it stops then out of the blue it will do it again I thought it might be the back Drums maybe the shoes came apart and were catching but they are fine everything looks fine, could it be the gearbox on the axle? I don't know...
View 5 RepliesFinally back able to start working on the Ranger and have a few questions.
When I got this thing back from my son it was running rough. I've fixed all the codes it was getting so no luck there now. Not sure how to explain it but, it feels like it is cutting back when driving at a steady speed and it idles rough. Not really like a miss but more like a hesitation when driving.
I've cleaned the MAP and IAC and changed the fuel filter. I also pulled the plugs and they looked good. My son installed new plugs and wires but he used the E3's and not sure how, or if, you're suppose to set the gap. I haven't checked the PCV yet because haven't figured out how exactly you get it out without pulling the intake.
So, where to look next? I'm kind of thinking the cam sensor but think I'll leave that to a shop sense I want the shaft replaced at the same time.
Today on my way to work my 1993 ford ranger would shift fine but would refuse to go over 35mph and shook pretty bad. I don't know where to start...
View 6 RepliesI have a 98 Ranger SuperCab XLT 4WD 4.0 Auto. Occasionally, especially when it has been sitting for more than 3 days, it shakes for maybe 30 seconds on startup. It smooths out gradually after that, maybe 15 sec. to normal smoothness. It seems like it is firing on all cylinders and is more like something out of balance.
Never does it when sits less than 2 days. When it happens, the longer it sits the worse it shakes.
02 ranger 4.0 v6 auto has 110000 miles on it. at highway speeds 65-70mph feels like it strugles to shift, truck will shake and bounce some. when this happens rpm's jump from about 2200 to 3000-3200 after a little bouncing rpms drop to normal. issue seems to be the worst going up hill but will happen every time i hit 65-70. Also the truck will not bounce or shake with the OD turned off and seems to run fine this way.
tranny fluid/ filter just replaced with no change. new plugs and wires
I am considering purchasing a 1999 4x4 ford ranger. The original owner has receipts for everything done on it recently. Rebuilt transmission, New ac, New shocks, new tires. I have never owned a ford but I always loved my friend's ranger. The only problem I had with it was an occasional clunking/rattling noise when test driving. I have read and was told this can be a common problem.
View 1 RepliesI was driving up a hill an it started to loose power. i got up to the top of the highway an stopped an it just shut down. got towed home i thought it could of been the alternator but dose not seem to be. took the belt off to spin the motor an its not spinning. drained the oil an there is no metal in it to see if the motor was done. i try to start it an it just dose a click click an that's it. Is the motor done or is it a transmission problem?
View 3 RepliesMy 95 4.0 has had a periodic idle issue for quite a while. It seems it may be getting worse. Here is when it may only happen:
Vehicle is fully warm. I shut it off for about 1 hr or so and when I restart it, it shakes and misses in idle. It will idle fine after I drive it around or if I rev the engine for a while when still parked.
This never triggers the "check engine light". New fuel filter, plugs and wires.
My left brake caliper locks up on me. I have replace it, the brakes , and the wheel bearings. when im driving down the highway and go between 45 -55 my front end shakes really bad and i start to lose power.
View 8 RepliesMy 88 2.9 ranger keeps heating up badly while idling. Was waiting in the drive-thru at Wendy's and it was taking them longer than usual, the temp guage started climbing closer and closer to 'H'.. I revved it up a bit to a fast idle (1500-2000rpm) and it did not work much... figured the gauge was being screwy. But when i finally got my food and started moving the truck was pinging..it really was hot..
But as soon as I got her moving at a steady 40mph, engine cooled back down to normal temp as if nothing ever happened..i put an extra wide two row aluminum radiator from a 4.0 explorer in it, fan clutch is not very old, no coolant leaks that i can see.. can't figure out why it heats up so much so fast at idle. Not enough air or coolant flow?
so I have a 1987 2.9L Ranger that likes to stall out when its idling after reaching temperature. Ive replaced all sorts of sensors (IAC, Coolant Temp, and PCV) and so far no luck. I was trying to figure out what the relearn procedure was for the IAC or get an input on any other possible sources of error. I haven't changed TPS yet.
What the engine does is when it gets up to temp, the engine will start to loose speed, and will start to shutter. Then it'll kick back up run fine for a few seconds and drop again, it'll do this for a few minutes then completely just choke out.
I have a 95 4.0 EFI inside of my 83 Ranger. Once the motor warms up, it starts to have an idle issue. I have to press the gas, in order for it not to cut off. Here is a video I posted a while back. A person suggested that it could be the MAF needed to be cleaned. I did that, and it did not work.
View 9 RepliesMy '04 Ranger has over 240k on the odometer. Runs great and has never given me any issues. Everything checks out OK - all the fluids, filters, and whatnot are in good shape. No CEL or any other indication that anything is wrong (except for maybe the IAC valve and clutch slave.)
I've noticed, though, that when I fire it up in the mornings to let it warm up while I scrape the ice and snow off the windows, the heat/defrost will not blow warm air. It doesn't matter how long I let it sit, it will only blow ambient air through the ducts.
When I get going down the road, however, the heat kicks in, after a bit, and works very well!
I've not found anything that would indicate an issue with the blend door or any other component and this is the first vehicle I've had that did this.
Is it normal for a 4.0 SOHC Ranger to do this? Or is there something I'm missing?... It's not really that big of a deal, but I do find it a bit odd that it would do this.
I mentioned the IAC above - I think it's "sticking" every once in a while and, when it does, I'll hear a loud "thump" right before it idles down to around 1k rpm. I can't see how this would affect the heat, though...
Ok, I replaced the head gaskets on this truck a couple years back and now I am having symptoms similar to the ones I was having then. I am not entirely convinced that this is what is wrong however.
Symptoms:
Truck was idling rough until it warmed up
Truck takes forever to warm up or simply does not warm up
If/when it warms up it operates at higher than normal temp/almost overheats(it hasn't overheated yet)
Heater blows very cold air
White smoke(has been cold outside so not sure if due to temp or coolant)
Overflow bubbled when I shut the truck off, but it has only happened once so far
I am kind of at a loss, but like I said am suspicious of the head gaskets.
1990 Ranger 2.3L 4 cylinder. The truck idles so rough it dies. It runs fine going down the road it just seems to "load up" at idle. I know there are hundreds of things that it could be, I just hate to start throwing parts at it. It is definitely running rich at idle.
It is one of those trucks that we have replaced a lot of parts. The scan tool said something about setting the timing??? Is there a way to set the timing? There is no distributor, and it is the one with 2 coils and 8 plugs.
backed out of the garage fine later in the day went to put it away started hard would not idle and only rev to 2500 .cleaned map sensor,egg valve tested and it works.cleaned the IAC and that works ,fuel pressure is 58psi. starts hard it would idle now it doesn't dies, no code . with 58psi could the pump still be bad? it has 18 pounds of vacuum. where is the vacuum line for the fuel pressure regulator on the motor?
View 14 RepliesI have a 2006 Ranger XLT 3.0 that is vibrating hard/rough idling, cel is on (solid, not flashing), has trouble accelerating with pedal punched. Will sometimes get a sudden burst when pedal is punched with rpms going up but most of the time no to slow raise of rpms with pedal engaged. Hooked code reader up to it and read ignition coil. Replaced the coil and changed plugs and wires. Truck still not running right. what gives? Is this a fuel pump, cats clogged, cylinder issue?
View 4 RepliesMy '99 volvo s70 t5 with 132k miles is idling poorly causing the car to shake, and the mechanic who looked at it said I am not getting compression in cylinder #5. He recommends a valve job (not sure if it is the intake or exhaust valve but said 95% of the time that is the issue). The mechanic said they completed the compression test, and that is what told him it was cylinder #5. Cost is 3200-3500 for the repair.
and if the price is accurate. Given the age and mileage on the car, I am reluctant to invest 3-4k.
I have a 2001 Ford Ranger with stalling problems. Recently I have narrowed the range of possibilities to a fuel delivery problem. The truck has 85,000 miles on it and I had the fuel pump replaced about 10,000 miles ago, the fuel filter was replaced at the same time. The stalling usually happens after it has run for a while and can happen while idling or driving at any speed. . .whenever it lacks fuel. It will restart and run ok for a while after if you leave it alone for a half hour or more. Over the last few months it has happened with greater frequency to the point where I am currently not driving it. I can get it to stall in my driveway by letting it run for ten min. or so. I am getting two computer codes: PO 402 and PO 453.
View 5 RepliesMy Yukon, with 140,000 miles, will sometimes start/fire up right away but other times it sluggish to start and then when it finally does it will shake for a while. Also, sometimes when idling at a stop light it will shake. It will also shake sometimes when I get around 60-70 mph. The rpm's are fine.
I replaced the fuel pump last spring and had a tuneup last summer. What could be causing this? I've had my mechanic look at it and he's hooked up his handheld diagnostic tool to it and it never shows any codes.