Ford Ranger / B-Series :: 1999 - Running Lights Will Not Turn On
Mar 14, 2013
I recently replaced all my incandescent lights on my 99 ford ranger which makes my truck stand out, but the issue I am having is all my exterior lights work including my turn lights but my running lights will not turn on. Is there any way I can fix this problem. I changed my flasher unit with one that is LED Capatable and i added load equalizers to the back to correct the issue with my turn signals but i just cant get my running lights to work....
View 14 Replies
Advertisement
I have a 1996 ford ranger and i have no tail lights i have license plate lights, brake lights, Hazard and turn signals. But no running lights on the rear end. Where the grounds are for this circuit and if some one has a schematic for this ranger...
View 9 Replies
Today I've been working on fixing the Door Ajar problem that's developed in my 2002 ranger extended cab. I haven't made any progress taking the main doors apart and testing the switches. Doing a little research on the forum I learned that the door ajar wiring is tied in with the dome/instrument dimmer. Well that's interesting because my instrument dimmer was never worker properly. It dims the running lights instead of anything in the cab, and if I turn it down too low, the fog lights won't function.
So I have a few questions:
+What's the way to determine which door, if any, is sending "door ajar"? I'd rather not take the back doors apart, and check the wiring on each door.
+What's the deal with my dimmer?
View 9 Replies
I have 87 Ford Ranger. 2.9L 4x4. Before any tips, I have checked the fuses, I have changed the Switch for the lights and the instrument cluster. Still no luck. I don't know if there is something wrong with the wiring. But what I was plan on doing is finding out on one of the Wiring Harnesses on the back of the Cluster which wire turns on the back lights on the cluster. Everything else on the cluster works (Gauges, Highbeam indicator, all the warning sign lights). What wires are what on the wiring harnesses. I was going to just run the wire to its own switch.
View 1 Replies
Having a problem with the brake lights. When the brake pedal is pressed, the running lights (including dash lights, parking lights, and the low power filament in tail light) turn on, but no brake lights. When the lights are turned on and brake pedal is pressed, the brake lights do not turn on at all. The 4 way flashers and signal lights work correctly with lights on and off. Things I have tried:
Replaced the tail light bulbs.
Checked fuses (#5, #10).
Disassembled the brake switch and bypassed it with a jumper wire.
Checked the grounds (tail lights, rear ground, drivers inner fender).
Tried to trace the wiring. Didn't see any noticeable damage, but the wiring is in a loom so it is hard to see.
Used contact cleaner on brake switch, rear wiring harness, body harness.
Still hoping it may be something simple that I've overlooked.
View 10 Replies
One of my bulbs sometimes doesn't come on when I turn my lights on. I actually have to hit the dashboard to get it to come on. Does it randomly. Ironically, it's been doing this ever since I pulled the instrument cluster out to change a different bulb. I don't know if I did something when taking it out or putting it back in. Anyway, what I can check to see why it's doing this? It's just one bulb that illuminates the right portion of the tachometer.
View 1 Replies
I live in Kansas and was home in Georgia for the last 2 weeks. The truck drove great there after a fuel up started missing and surging at 50 to 70 thought it might have been bad fuel. waited till it was low added Lucas fuel treatment and premium gas still was doing it. no check engine light. went to Advance and fuse for light was blown they checked and was getting mass air flow code. unplugged it and seemed to be better, not perfect but better. plugged it back in and went to do it again. Changed mass air flow night before the drive back to Kansas. Ran well from Savannah to north Georgia then started doing it again the rest of the way home. Going to have advance check code again.
View 12 Replies
When it rains my "door ajar" light comes on and the overhead lights won't turn off. that's the common problem. i've read many threads where it says to spray liberally with WD40. i intend to do that but the plot thickens.
Usually, after a few dry days, the light goes off and everything returns to normal. Not so any more. the newest episode entails the light staying on for two weeks of good warm, dry weather. naturally i always take the bulbs out. Now, its somewhat sporadic but.... I'll try to explain since I'm still trying to wrap my mind around it.
1. light stays on, dome lights won't go off.
2. tried dome lights couple of times, still wouldn't go off
3. finally, inserted dome lights and they wouldn't come on (except when manually switched on) however the door ajar switch was still on.
4. EXCEPT when i opened the passenger door the domes came on but wouldn't go off so i took the bulbs out again.
5. that's where i am now.
Not positive but I'm thinking since the new wrinkle in established expectations that I'll probably end up replacing the driver's switch. Before I tear up the door panel i need some hints concerning removal. the door has power windows and locks (which i need new actuators but that's a different story). Is there anything I need to watch out for?
View 3 Replies
2013 F250 XL with factory towing package.
My camper and boat trailer do not have turning signal or brake lights when plugged into the round seven pin trailer connector. I have tried both the connector in the bed and under the bumper. I've also connected the trailers to other trucks and the lights work fine so I know the problem is in my truck.
View 9 Replies
I had the intake manifold and battery replaced on my 99 Ranger and now when I got it back it worked just fine except the factory radio wouldn't turn on. Headlights​, blinkers, AC, dash lights, etc. All worked just fine but the radio will not turn on. I bought an aftermarket radio to put in it when it got out of the shop but with the factory radio not turning on I don't want to replace it until the issue is resolved.
View 2 Replies
My 1999 4.0L v6 Ranger (auto trans) is having some issues. Recently the fuel pump won't turn on as normal when I turn my key. I have to turn the ignition on and off 10-20 times before I hear the pump kick on and I can start it. I already checked the relay and fuel pump shut-off switch. Neither was the bad.
View 10 Replies
Went from right around 18 to 14-15 last 2 tanks. No codes, drives absolutely normal. I have had my 4x4 lights flashing, but the 4x4 has never worked (suspect its a combination of the transfer case motor and the pulse vacuum hubs). Used to flash like this when I would try the 4x4 switch and would take a while to "get back to where it was happy". Recently I have not messed with the switch or anything else.
View 14 Replies
My brother has a 99 ranger with the 4.0 engine and factory tow package. After installing a rebuilt engine the brake lights do not work and the turn signals will blink both sides like flashers. Lights on the truck work fine. What connections may be hooked up wrong or where to start looking for the problem.
View 3 Replies
99 Ranger XLT 4.0 4WD Automatic. With the turn signal blinking and I depress the brake the turn signal stops blinking until I release the brake. Where to start.
View 2 Replies
I just bought my 2016 super duty about 2 months ago, really liking it, got a couple questions- How do I turn off daylight running lights? When head lights are on, instrument cluster lights come off and on according to outside light levels, can I turn off this feature?
View 1 Replies
No straight answers found yet. It's just the running lights that get stuck on.
I don't have auto lights, and after a period of a minute or 2 the lights pop off. There must be a relay sticking somewhere.
Looking for a diagram that shows where the relay for running lights is located?
View 1 Replies
2003 ranger xlt 4wd electrical - My radio lights up when driving lights are on but no clock display or anything else. My cigarette lighter and aux power outlet do not work and mym 4wd does not work. when i try to change from 2wd to 4wd no lights come on in the dash. I have checked all fuses and they are good. What to check next?
View 4 Replies
My brake lights will not work but all other lights do, bulbs and fuse have been replaced.
View 2 Replies
I was adding some more running lights today and tried to tie in to the front running/turn signal light. Next thing I know I hear a pop and now no turn signals, hazards or brake lights on my 99 F250 SD V10. My 3rd (center) brake light does work though when I press the brake, it's just the tail brake lights that dont work.
I can't find a blown fuse for the turn signals or brake lights (not really sure which fuse box it's in since the manual doesn't tell me what fuse is what)
I however did find what I'm guessing are the flashers behind the radio. What might have went wrong where before I start dumping money in to flashers and relays.
The next question is, can I jump in to the marker/turn signals and add another single LED light to them off the front? If I can which color wire does what?
View 9 Replies
I have a 1995 Ford f250 Powerstroke and i do not have turn signals, rear running lights, brake lights or reverse lights. i checked the fuses and they seem to be good but i dont want to tear everything out to check the harness if it could be a bad ground. any insight?
View 1 Replies
1986 Ford Ranger / 2.3 EFI / 140 CID OHC /4-Cyl/5 speed
So the last time I was here, I was having doggy issues which I thought were fuel related. I'm still having issues, although it appeared to cleared up a bit.
When I start the engine, it cranks over, I'd give it some gas, it would rev up, then suddenly die, no matter if I pressed down on the gas pedal or not. After two or three times doing this, it would turn over and maintain a steady idle, then off I go.........
The problem now? Well, late today I tried to get it going, and after about 15 times, I gave up. It would not stay idling, it would crank over then die. I did not want to ruin the starter. It seems the gas pedal is worthless after the engine decides to conk out, and no matter how many times I step on the gas pedal, nothing happens.
Has been replaced within the last few months:
Fuel filter regulator,
Inline fuel filter,
Cap and rotor,
Lucas fuel injector cleaner,
ECC computer, and Fuel relay switches, (multi-function relay/connector switch)
Air Control Valve - Removed and cleaned.
Checked all vacuum hoses.
Has not been replaced:
Map Sensor, (was told it's located on Pass. fender wall, but can't find it, according to the manual)
EGR Valve and sensor,
Throttle Position Sensor,
EVP sensor,
Spark plugs, (two years ago)
Plug wires, (two years ago)
Ignition control module, (replaced about six years, or more)
With trying to keep the gas going to turn it over, it does not, so to me, it seems to be more of a fuel problem than electrical, but I'm no mechanic.
View 6 Replies
