Ford Ranger / B-Series :: 1999 - Radio Won't Turn On?
May 17, 2017
I had the intake manifold and battery replaced on my 99 Ranger and now when I got it back it worked just fine except the factory radio wouldn't turn on. Headlights​, blinkers, AC, dash lights, etc. All worked just fine but the radio will not turn on. I bought an aftermarket radio to put in it when it got out of the shop but with the factory radio not turning on I don't want to replace it until the issue is resolved.
View 2 Replies
Advertisement
My AC clutch, radio, cruise control, and turn signals are not working. I have checked all fuses and relays that I can find, all good. From what I have read, these are not part of the GEM function. What I need to check next!
View 7 Replies
I have a 99 Super Cab 4x4, 4.0, XLT. The radio has terrible static and the back lighting of the climate control goes off and comes on at different intervals. Are the two issues related?
View 1 Replies
I recently replaced all my incandescent lights on my 99 ford ranger which makes my truck stand out, but the issue I am having is all my exterior lights work including my turn lights but my running lights will not turn on. Is there any way I can fix this problem. I changed my flasher unit with one that is LED Capatable and i added load equalizers to the back to correct the issue with my turn signals but i just cant get my running lights to work....
View 14 Replies
My 1999 4.0L v6 Ranger (auto trans) is having some issues. Recently the fuel pump won't turn on as normal when I turn my key. I have to turn the ignition on and off 10-20 times before I hear the pump kick on and I can start it. I already checked the relay and fuel pump shut-off switch. Neither was the bad.
View 10 Replies
99 Ranger XLT 4.0 4WD Automatic. With the turn signal blinking and I depress the brake the turn signal stops blinking until I release the brake. Where to start.
View 2 Replies
I have a '97 Ranger 4.0 4x4 5 speed, as the title says... my radio does not work. It has an original cd radio and I had installed an aux cord. After I installed it I could only get a select amount of radio stations, last week I had went out of town so I didn't drive it at all, I came back and there was what seemed to be no power to the radio at all. No display, no sound. Only the lights on the radio controls (pre-sets, volume, seek, etc.) I have checked the fuses, pulled the radio and checked everything from behind and still nothing. Could the radio its self be bad? What else should I check?
View 1 Replies
My 1996 Ranger Supercab XLT has the stock radio with 6-cd changer. The unit works fine but only the frequency/clock display lights up. I'm not sure where to start to fix it.
When a problem first occurred, the frequency/clock display flickered/dimmed randomly (and I think the other lights were fine). It was in the shop a few times for a fuel pump problem (the after market pump was actually not compatible and it took a bit to figure that out), and at some point after I got it back I noticed the display was fine but the remainder of lights didn't work.
I don't know if the shop did something or the failure behavior changed. What to look at? I can open the radio and fix that if needed (or replace it).
View 6 Replies
I have a 2011 Ranger. It came with Sirius radio which works with the AUX button on the head unit. This setup is not what I am use to. Anyway I want to replace the OEM unit with an aftermarket. My question is will this AUX connection effect an aftermarket radio connection?
View 11 Replies
Wiper problem is that they only work on high. The symptoms are as follow. The relay is working as the controls are ran thru the intermittent steps. I have tried two control switches and they acted the same. So, I believe the problem is in the motor. There doesn't appear to be any wire problems on the plug so it must be inside the motor. Could this be that grease problem inside the motor and it just needs to be cleaned and re-greased?
Radio, Has power to the plug but doesn't work at all. It doesn't appear to have a head unit fuse that I keep reading about. I have not tried to hook it up direct yet but will try that tonight. I am trying to get this truck ready to sell and need to get these items cleared up.
It is a 2001 XLT Extra Cab 4X4 with a 3.0.
View 14 Replies
This interference correlates directly to tire rotation speed, engine rpm has no effect. Under about 5mph it won't make the noise, but over that you hear a pop more or less for every rotation of the tire and when you hit say 50mph it is just a steady static noise on AM only. Haven't pulled the head unit yet, checked several body grounds under the hood and all are good. Don't know if a damaged wheel sensor could cause an issue or not.
View 4 Replies
Truck has no spark except when you first turn key on it sparks or right when you let off from cranking it will give one spark. You can be cranking it and nothing and when you let off it kinda acts like it wants to start for a millisecond.
View 11 Replies
I have a 1988 ford ranger and my headlights won't turn on all my fuses are fine but no headlights! All the other lights work fine blinkers, parking, brake ,and tail lights! What do I need to look for????
View 14 Replies
My dome light will not turn off. I have tried the WD40 in the latch trick and replaced both of the switches. The dimmer is not all the way up. I don't know what else to do.
98 Ranger XLT, V6, Manual windows.....
View 14 Replies
I have a 97 ranger with 3.0 it runs great but once you drive it and shut it off and go to restart it it will turn over but not start it used to start once I let pressure off the fuel rail, but now is a little harder to start when it does this but it looks as thou coolant comes out of the reservoir when this happens I think it might be coolant sensor or thermostat problem causing the timing to advance until it cools but then again why was it starting when I released pressure from the fuel rail and also I don't believe my check engine light works...
View 8 Replies
My buddy bought this 2000 Ranger 4x4 with the 3.0 and 150,000 miles for 500 bucks. After he bought it, the number 2 spark plug boot caught on fire, and turned completely to ash. So we parked the damn thing, and have been training ever since, but it did run when we parked it. We replaced all plugs, wires suspecting a bad plug (and they were all fouled). Went to start it and now its on the verge of starting, but can't quite get there. So here's what we've done since.
-Replaced coil (had it tested, failed primary test on terminal 1, and secondary on 3 and 4)
No change
-Checked Spark by grounding spark plug
Good
-Checked Fuel at rail
Good- Held until empty, primed Fuel system (key on for 3 seconds 5 times) checked again, good)
-Truck had been sitting for three months, so put in small bottle of stabil and added 5 gallons with Lucas. Primed the system about 20 times, and tried to start. No effect.
-Checked battery.
1 bad cell, 3 low on water- replaced battery. Allowed it to crank for longer (before we were jumping it) but still didn't want to.
Note of concern : After we replaced the battery and went to start it, when the key was disengaged I noticed a hissing sound coming from the radiator cap. The truck is in Upstate new york and hasn't been ran in 3 months. I'm hoping its not but thinking it is a cracked jacket or a blown head gasket.
View 8 Replies
It's a 01 Ranger 3.0 V6 5 spd 2wd. He drove home from work then the next morning wouldn't crank over. Turn the key and it doesn't even attempt to crank. All dash lights, headlights, etc come on. Battery is good. Took starter out and tested at parts store. Tested good. Clutch switch was good. Replaced ignition switch with no change. If I jump the solenoid on the starter it will turn the engine over. When turning the key I can hear the starter relay in the fuse block under the hood clicking. All fuses were good. I found the main engine ground wasn't hooked up to anything. I hooked it back up and still nothing. All battery connections were good but cleaned them anyway. Not really sure where to go from here.
View 6 Replies
I have 87 Ford Ranger. 2.9L 4x4. Before any tips, I have checked the fuses, I have changed the Switch for the lights and the instrument cluster. Still no luck. I don't know if there is something wrong with the wiring. But what I was plan on doing is finding out on one of the Wiring Harnesses on the back of the Cluster which wire turns on the back lights on the cluster. Everything else on the cluster works (Gauges, Highbeam indicator, all the warning sign lights). What wires are what on the wiring harnesses. I was going to just run the wire to its own switch.
View 1 Replies
2007 Ranger XLT 2.3, 55k miles
Went to start truck today and got very little response.
Symptoms:
Workee:
Dome light (regular brightness)
key in/door open chime
No workee:
Dash lights
Solenoid (no response)
Headlights
Radio
Turn signals
Hazard lights
VOM tested battery- 12.82 V
Cleaned battery terminals
Every key turn there is a brief low chatter from interior fuse box.
Occasionally dash lights will flash briefly on key turn.
Occasionally PATS dash light will flash in 2 second cycle.
I'm suspecting the ignition switch but the no headlight condition puzzles me.
View 8 Replies
I have an 88 ranger with the 2.9l. The headlights work and the markers do to. The brights don't though. and also none of the turn signals work, the brake lights work though but i don't think the reverse do, I can't see them. Do the turn signals and brights share a fuse on there own? How to diagnose it or what it may be?
View 9 Replies
Having a problem with the brake lights. When the brake pedal is pressed, the running lights (including dash lights, parking lights, and the low power filament in tail light) turn on, but no brake lights. When the lights are turned on and brake pedal is pressed, the brake lights do not turn on at all. The 4 way flashers and signal lights work correctly with lights on and off. Things I have tried:
Replaced the tail light bulbs.
Checked fuses (#5, #10).
Disassembled the brake switch and bypassed it with a jumper wire.
Checked the grounds (tail lights, rear ground, drivers inner fender).
Tried to trace the wiring. Didn't see any noticeable damage, but the wiring is in a loom so it is hard to see.
Used contact cleaner on brake switch, rear wiring harness, body harness.
Still hoping it may be something simple that I've overlooked.
View 10 Replies
