Ford Ranger / B-Series :: 1999 Mazda B3000 V6 Started To Stall Whenever In Idle
Apr 3, 2015
I have a 99 Mazda b3000 v6 that has recently started to stall whenever in idle. Check engine light is on and the following codes popped up (P0176, P0135,P0141, and P0155). I'm sure one of these codes has to be related to the problem but I am clueless when it comes to troubleshooting. Also it started stalling after I filled up the tank. Not sure if that has anything to do with it, check engine light was already on before that.
View 2 Replies
Advertisement
2002 Ford Ranger edge 3.0 flex ... Truck was running fine and giving me no issues. I woke for work the other day and went to get coffee and truck wouldnt start. I could hear fuel pump running and knew it wasnt that, it was acting flooded. So today I pulled fuse from fuel pump relay, and got it to start. Put the fuse back in and ran to gas station. On the way to the gas station it started running really rough, very low and rough idle, trying to stall out. I noticed it had black smoke coming from exhaust. I got it home, and got it to start barely, and it has the same very low and rough idle, but my oil gauge was going crazy, flickering back and forth all crazy, and the idol is terribly rough and eventually stalls out. Earlier today I did put new spark plugs in it, but not sure that has anything to do with the issue. I also hooked it up to a computer and it isnt throwing any codes.
View 13 Replies
I have an 87 ranger, 2.3 4cyl. 2wd 5 speed. When I start up the truck after it sits for a few hours it will idle fine but then it starts to bog down and wants to stall but after about 5 mins its fine and runs like a champ. I don't know if its a sensor or what.
View 2 Replies
My mazda b 3000 shut off while at a red light i t turned over initially 3-4 times now nothing. changed EGR, ECM, CRANKSHAFT AND CAM SHAFT SENSOR three weeks ago. brand new battery, took alternator in and it was bad so i replaced. theft light is blinking rapidly?
View 2 Replies
2001 M B3000 v6 my sons truck w 122k. He is overseas and I took it to deliver a CB750 bike to my brother in law... 4oo miles away from my place.
In the middle of nowhere TX it developed a bad miss or knock, almost a shudder in the 2 to 3 k rpm range. Idles ok just below 1k runs fine at 70 mph as long as the rpm is near or over 3k.
Not sure I want to turn around and drive back the 400 with it running like crap. I will take it to Autozone and pull codes tomorrow a.m. but what should I expect?
View 9 Replies
All my guages move (needle moves to the right) once I turn on my head lights. Indicating higher egine temp and higer oil pressure. What cause be causing this?
View 4 Replies
I have spent two days searching for a fix to a problem like mine on my truck and I haven't quite found it. Sooo, here it is. I have a 2000 Mazda B3000 4x4. I'm getting the dreaded six lights flashing. I can hear the clicking under the dash as it attempts to engage the 4WD. I have checked the Motor at the T/C and no power. What feeds voltage to the motor its self? and is there any other thing I can check B-4 having it scanned? oh and it is a manual tranny.
View 4 Replies
1991 2.3L 5 speed .... Okay here's my list of issues.... At idle will stall out, its almost as if i shut the key off, or sometimes taking off it'll sputter and stall, fuel filter has been changed. Back part of the tranny housing leaks, is there a gasket for that?
View 3 Replies
I have a 87 ranger with a 2.9 and recently it started to act up when i start after its been sitting for a couple hours it has a rough rolling idle and will stall out and a lot of white smoke out the tail pipe and some times a tiny bit of black smoke when revved high....after a about 10 mins of feathering the gas it will even out and runs no problem.... oh and quite a bit of moister comes the tail pipe....and this issue just occurred over night every time before never had an issue like this...
View 5 Replies
My ranger 2.9 automatic 2WD has an high idle when started for about 6 min, engine can be hot or cold, still get the high idle, then it will drop to around 900-1000. I've changed the Idle control twice, checked EGR function. Replace temp sensor. Disconnected battery for 15 min. No code output.
View 7 Replies
I have a 99 ranger with 170000 miles and the front end recently started squeaking. its coming from the driver side but I can't pinpoint it.
View 5 Replies
So a couple days ago I started my truck and it fired up like normal, but then sputtered out and died after a few seconds. I tried starting it up again and it did the same thing. I tried once more and it started up fine and I drove away.
It sounds like my truck is running out of breath or something and just sputtering out. Runs fine once it turns over though. My issue is that it is happening almost every time I start it now. I have to turn it a couple times before it catches. What this might be?
View 11 Replies
I was driving up a hill an it started to loose power. i got up to the top of the highway an stopped an it just shut down. got towed home i thought it could of been the alternator but dose not seem to be. took the belt off to spin the motor an its not spinning. drained the oil an there is no metal in it to see if the motor was done. i try to start it an it just dose a click click an that's it. Is the motor done or is it a transmission problem?
View 3 Replies
Quick back story I bought a 1999 Ford Ranger It is a 4 cyl with an auto trans the guy said it had some trouble with the tranny (major understatement) he also forgot to mention he cut out the CAT. so running a 4 banger off the header.
When you start the truck it rough idles but you have to hold the gas down til it warms up. You can shift into reverse but it labors the motor and the motor will not up the rpms kinda stays at idle and wants to die no matter how hard you accelerate and you can't move up a slight incline.
When you shift into drive you have to rev the motor to 3 grand an it will catch then move slowly forward. no matter how high the revs go. The fluid levels are a tad above the full level and a bit dark for my liking.
Ok, I used an OBDII scan tool from the parts store and it came up with 3 codes P0351, P0352, P0500. From my internet search the first two seem to be coil related which explains why the motor is running like garbage. The last may or may not have to do with what the tranny is doing.
View 2 Replies
I have a 99 Ranger w/3.0. It idles about 1500 rpm cold,and 1200 warm. Here are the things that I have tried.
1.Checked ALL vacumn hoses/lines
2.Changed Air idle control sensor
3.Throttle position sensor
4.removed and completely cleaned throttle plate in throttle body.
5. removed top of intake manifold and checked for cracks and/or leaky gasket.
Nothing seems to change. Could it be a faulty ecm?
View 6 Replies
I'm having an issue with a misfire whenever I start my truck. It happens regardless of whether the engine is hot or cold, and lasts for about 10 minutes. I had a similar issue not too long ago, except last time it just stopped starting all together until I had the injectors cleaned. I have new plugs, wires, new coil pack, and a semi recently replaced fuel filter. I'm hesitant about it being the injectors stuck open again as its only been about 1000 miles since I had them all cleaned.
View 5 Replies
As the title states, I have a 2002 Mazda B3000 series Pickup and while everything is working great, the a/c is driving me insane!
Here's how it goes:
- Start the car, turn on the A/C, hear a click
- As I drive, after 10-20 minutes, the A/C would just either switch to (what I think is) vent; it blows humid, warm air.
- Another way to turn it off is to accelerate quickly; Note: these two scenarios are sometimes inconsistent
- Sometimes, it would occur, while other times it would just randomly turn itself off
- A solution I've found is to switch over to vent, leave it on there for a few minutes, then switch back to A/C; works for another 10-20 minutes
What I have done to fix it is to replace the freon (even though, it was never really empty; still isn't empty) and have replaced the fuse associated with the A/C.
View 2 Replies
The garage said that the "carrier bolt" is broken. What is this and is it a harbinger of more death to follow? This truck is rowdy and distrustful to drive to begin with.
View 4 Replies
For the last 2 years 1995 ranger 2.3 will run great but every 1-3 months will just stall. Will than try to start it for a couple of minutes and in 1-8 minutes will start back up again as if nothing was wrong and then be fine for another week, month, 2 months etc. It has never happened at first start up in the morning but at times will stall 2 minutes after start (at traffic light of course). At times will turn off to run into store, come outside, no start, try for couple of minutes and then starts up fine. Changed out fuel pump, etc, etc. Biggest problem is no codes and, of course, when mechanic looks at it nothing is wrong.
View 4 Replies
Why my trucks engine is cutting out. idles fine and runs fine when on the road, it only stalls in park if i rev the engine, and it stalls immediately when i put it in reverse.
I took it to a shop and they scanned it and said it was a o2 sensor problem. replaced both o2 sensors(they were both bad) but no luck there, still having issues.
View 2 Replies
I've got a 99 Ranger. A month or so ago, it started to be a little hard to start. It would turn over, but not fully start unless I gave it a little gas. This did not happen all the time, primarily it happened after it had sat all day when I left work. Not long after that started, my check engine light came on. The codes were for a lean mix as reported from the 02 sensors. Before I could dig any further, it just wouldn't start at all one evening. This was after I had driven it for 30min and then parked it for an hour or less. But this time it was different in that the solenoid would just click, but that was it, like it didn't have enough power to turn over. I took the battery to have it tested and it had been severely discharged.
I got a new battery as that one had reached it's limits. Put it in and the truck started right up no problem. A few days later it started acting up again like it had originally, I had to give it some gas to get started. I had the alternator/starter checked, both were fine. A day later, it got so bad that I had to shift to N and keep giving it fuel anytime I stopped the truck. I had to do this all the way to and from work. Now this morning I go out and it starts right up, no issues, no dying at idle and didn't have bit of problem coming in. Initially we thought it must be a fuel pump, but then I can't explain why it worked fine this morning. I changed the fuel filter less than 2 years ago, so I wouldn't think it would require changing already. Wondering if there's a sensor issue, one that calls for appropriate amount of fuel?
View 2 Replies