Ford Ranger / B-Series :: 1999 - M5OD Popping Out Of Third Gear Occasionally
Oct 3, 2005
My M5OD in my 1999 Ranger 4x4 with 3.0 occasionally pops out of 3rd gear. I think it does it only under light throttle or coasting. Also some vibration, especially in 3rd gear. Once in a while the gears grind when shifting into third. Truck has 145,000 mostly highway miles. Frequent fluid changes with Redline D4ATF.
What could be the cause, bad synchros ? How hard is it to remove the transmission and make a repair for something like this, what kind of special tools, etc. I assume a transmission jack would be real useful, what else would I need other than the normal wrenches and sockets ? Is there a good shop manual recommended for doing this repair ?
View 4 Replies
Advertisement
So my new/old 2004 has another issue. Parked at the grocery store tonight on a very slight incline backwards. Put the Ranger in park (automatic shift) and before I could fully engage the parking brake it began to roll back with a clunk, clunk, clunk as if popping out of gear.
Need less to say I moved to another spot that was more level. Just an hour before I parked the same way on a steeper incline and did not get this. Now I need to watch this carefully until resolved. How to remedy this issue.
View 3 Replies
I am considering purchasing a 1999 4x4 ford ranger. The original owner has receipts for everything done on it recently. Rebuilt transmission, New ac, New shocks, new tires. I have never owned a ford but I always loved my friend's ranger. The only problem I had with it was an occasional clunking/rattling noise when test driving. I have read and was told this can be a common problem.
View 1 Replies
My 1999 Ranger with 4.0 EFI V6 engine makes a "sucking sound" occasionally. At first I thought it was a belt slipping, but now I believe it is some kind of intake air leak. If I stop the truck while the sound is on, I can open my driver's door and get to about the front of the hood before the sound stops. I have never been able to observe the engine with the "sucking sound" on. Sometimes the engine will kill when the "sucking sound" stops, if the engine is idling and in gear. If I just keep driving normally, there does not seem to be any permanent problem. What the problem is?
View 4 Replies
I have a 1999 ford ranger 2.5L. When I turn the key to the ON position, right before the ignition turn, everything comes on like it's supposed too. However, if i try to change into reverse, the truck will start without me even touching the key. Also, if I start it using the key and try to go into reverse, the starter engages and makes the all to familiar grinding sound. I am completely stumped.
View 4 Replies
i have a 1999 mazda troy lee b3000. The truck has a 3.0 flex fuel and 4r44e and when you go to drive it. turn the key engine fires up but the trans won't shift into gear. Here is the back story.Bought the truck brand new in 99 I'm the original owner it was a daily driver up until 2 years ago. the truck has over 300k miles and still ran great but the camshaft was starting to go. I was gona replace the cam but came across a killer deal on a new engine. picked up another 3.0 flex fuel with 50k miles. drove the truck into my garage removed the old engine installed the new engine. got in the truck turned the key and the new engine roared to life.
I went to put the truck into gear so i could get it out of the garage and go for a test drive and nothing. went to put it in drive and again nothing. no matter what gear its put in it doesn't move at this point i was confused and decided to quit for the night. That was in 2011 its now 2013 the truck has just sat there sense then. I've tried anything and everything even went as far as swapping transmissions and computers with no luck. I took the trans apart I don't know how many times can't find anything wrong with it.
View 4 Replies
I just got a 99 2.5 rwd auto and it shakes when it's at idle in gear. I'm pretty sure its because the AC pulley is engaging drawing power. I was thinking about turning the idle screw up a blonde-one because when I hold the brake and give it slight gas it goes away.
View 3 Replies
I have a 99 Ranger 3.0L automatic, ext cab, 2 wheel drive. Door sticker show code "T" which I looked up as the 4R44E. The trans seems to be slipping in 1st and 2nd. Thought it was "reared shudder", from a "limited slip" differential but mine is not limited slip. just the regular 8.8 with 373 gears.
Wanting to know what if any options I have for buying a new / rebuilt tranny? I've seen where depending upon the year and motor, Ranger can have 4r44e, 4r55e, 5r55e, etc.
View 3 Replies
I have a 1999 ford ranger 4x4 with automatic 5r55e and it had problems shifting smoothly into third gear. I changes the valve body gaskets and the (rooster comb) detent lever. Now it shifts very hard and has on first second and passing gear.
View 6 Replies
Since putting my new exhaust on (post-cat)... I've had this "ping" occasionally from the exhaust. Sounds as if someone is taking a small metal bar and hitting the exhaust. Random intervals, pretty loud, does it whether the engine is off or on. Only does it when warmed up though. I can't narrow it down due to the randomness of it.
View 5 Replies
Okay so the other day my ranger wouldn't start after i got off work, it would turnover only occasionally but now it wont even do that. I've tried the fule turn on/off switch underneath the passenger glove box. I unscrewed the fuel like valve cap and pressed the pin but the fuel like barely squirted out so does it mean my fuel pump is bad or what??
View 9 Replies
Compressor clutch engages, lines are cold, when it works air is cold. A/C guy thinks the blend door isn't working right, is it vacuum operated or electric?
View 3 Replies
My 2002 2.8 diesel ranger has recently been serviced replacing the turbo and a complete overhaul on the engine performed. I road tested it and it runs smooth... However, I am hearing a popping sound coming from the intake air filter. I was told it is because of the new turbo installed.
View 2 Replies
While in the locked position, the steering wheel was purposely jerked hard to disable the mechanism on a 1996 Ranger. Now the truck will not steer easily or smoothly and a popping noise is evident when turning. I'm not concerned about having the wheel lock, but would like to be able to return driveability to normal.
The same guy who caused this damage also damaged the ignition. No key is needed to turn the switch now.
I'm lost as to how the steering locking mechanism works and wondering if I need to tear apart the column or if maybe there is a locking pin accessible that needs to be removed to regain driveability.
View 2 Replies
For about 6 months my 95 ford ranger 2WD 4 cylinder pick up has occasionally gone into "over drive" when it is not in gear the idle will get crazy high, like one of those party toys that yo blow into and it spins an makes noise. Once put into gear it calms down but it has more forward motion without gas than before. If it gets really bad at stop lights I will turn it off and turn it back on. It may still do it when I turn it back on but by then I will be putting it in gear. When it is in this condition and I turn it off it takes longer to turn off, like it is winding down.
I would say that this happens every 4th time it is drive, sometimes less sometimes more. There seems to be no rhythm. I took it to an electrical specialist and they could not find anything, and last week the check engine light came on so I took it to our normal mechanic. They did a test and found that the engine speed limiter had been reached which was why the check engine light came on and also pretty scary. The diagnostic codes were P0500 and P1270. I am worried 1. that this is making the care unsafe to drive even though it seems like we can manage it to a degree and 2. that is is doing damage to the car by putting it in such a hyper work mode.
View 2 Replies
I bought a 96 Ford Ranger XLT Supercab 4.0 on the 21st and the gear shifter doesn't go into 1st gear but changes to the other ones(see pic below) and was wondering if it's a easy fix.
Also I have a oil drip(at least it looks like oil to me) and I can't figure out where it's coming from because it's a small drip and the oil dipstick and tranny dipstick both show full and I can't figure out where the drip is coming from and I only noticed a dip on a metallic tank but don't know what that is either but check out the pic below to see the drip I circled.
View 3 Replies
ive been experiancing an issue with my trucks shifting. it shifts smoothly but doesnt like shift into 5th, as im driving it stays in 4th longer than necessary. my thought was that it was tied to a shift sensor, what do you think?
View 5 Replies
I have a 1998 ford ranger and it will not disengage out of 3 gear. The truck still starts but if you let of the cutch. Of course, It stalls. I'm doing the work myself but where I should start looking.
View 1 Replies
I have a 2000 ranger 4x4 4.0l ... It starts jerking in the 3rd gear and up and it gets worse as the gears changes... If it in higher rpm it doesn't do it as much I don't know what could be the problem it's been a recurring problem...
View 12 Replies
2003. Ranger xlt with the 4.0.... So I just bought this truck and was informed that the vacuum might not be functioning correctly. And here's the symptoms. It idles a little rough, nothing major. When I put the truck into gear either drive or reverse, it stalls out almost every time unless I give it some gas and hold the brake. But after that I could drive it all day with out a problem, as long as I don't put it into park. And last it starts a little hard. But the damn thing runs great while driving it. It's still very snappy even having high miles.
View 4 Replies
Not only will it not go into gear, truck will not start unless clutch is to the floor, and in neutral (it's only possible place) if you pick the pedal up 1/4 inch off the floor the odometer starts spinning around 1 mile in 5 seconds.... if you lift it any more it kills the engine like you shut it off with the key.... odometer reads 99,004 miles now (the last 2 are mine) I bought this truck like this ....
View 3 Replies
