I've noticed my RR emergency brake cable's outer casing rubs hard against the RR shock, such that it's rubbed through the cables plactic covering & is going after the metal jacket.
It's a 99 4X2 4dr extra cab long wheel base.
Notice this on your Ranger, LWB model, or for that matter any wheel base Ranger???
I bought 2000 Ranger with rear half of the frame cut and welded.
The mechanics who did this did terrible job of putting things where they belong. I rerouted wiring harness and rebuilt EVAP lines, but cannot figure out what is the correct route for parking brake cable.
Currently some part of the parking brake cable is sitting on the leaf spring. It may also be missing some mounting brackets or clips. Looking for a picture or diagram showing parking brake cable routing?
My battery went flat and to compound my misery, when I went to open the hood, the cable was snapped. How I can open the hood without using the release cable ? I'd rather not have to pay for it to be taken to the mechanic and then also pay to have the battery changed !
View 3 RepliesAfter taking apart my instrument panel to change the bulbs, I went to reconnect everything, but now the gear shift indicator isn't working. I can change gears fine, and everything else on the instrument panel works just fine.
The copper cable that connects to the shifter doesn't move when the shifter does. Is there a way to fix this problem, or do I need to find a replacement cable?
so i changed the speedo cable and speed sensor in my 93 ranger, but still getting the speedometer bounce. what could be next? the speedo housing in the cluster? lubed the inner cable, made sure nothing is kinked or sharp bends. Put in a new vehicle speed sensor while i was at it just bcuz. cruise control does not hold a steady speed either but i think the 2 are not related. I'm leaning towards the cruise control servo as to why it does not hold a steady speed. Most of the time once i get to around sixty i'm basically driving by ear bcuz the speedo bounces from 60down to 55 and back up.
View 3 RepliesI bought a 2000 Ranger 4x4 3.0L auto today from the neighbor guy sight unseen with a "bad tranny" for $400. I'm very unfamiliar with the Ranger family, but long story short:
When moving the shift lever, the trans doesn't engage. It needs to be engaged from underneath. Do the cables tend to stretch, or break? I can't find any adjustment on it anywhere.
i have Ksport kontrol pros and no mattter how i attach the brake line or abs sensor it rubs! how to rout them. i bought 3/8 heater hose for the brake line and spliced it to make a sleeve. sway bar endlinks used to pinch the ABS against the coilover but now it rubs the cv axle. 09 rolla s
View 2 RepliesHow to replace the parking brake cable from the pedal down to the connector on the frame? We got a 2000 F350 in the shop with a bad cable, and i never did one. And I don't really want to mess this thing up trying to figure out how to change it.
View 6 Replies1999 F-250 ... How does one replace the emergency brake cable? The cable in the '99 F-250 I recently bought broke.
The cable was sticking when I got the truck. I like to use the emergency brake every time I park. The previous owner(s) didn't use the emergency brake and the cable had frozen up.
I tried using it every time I parked. I could tell it was frozen, but I was hoping it would loosen up. It held a little bit when I used it; but soon it just broke.
What is the procedure to remove the parking brake cable from the axle? It looks like the cable has a locking device like the fuel lines but heavier. How do you get that thing out of there without destroying it?
View 9 RepliesI just put new rims on my truck which are 18x9 with a -24 offset. I swapped my 35s over from my stock wheels (which they didn't rub at all). When I put my new wheels on, the drivers side rubs really bad but the passenger side doesn't rub at all! I'm extremely confused why this happens. I know negative offset will make the wheel rub weird. But why is it only happening on one side and not the other?
View 10 RepliesI'm re-doing the parking brake as part of a rear brake job on my 2009 F250. I need to disconnect the intermediate brake cable at the equalizer, but am having trouble. I've got slack in the cable, but can't push hard enough to get the swaged cable end to move within the connector that's between the equalizer cable and the intermediate cable.
Is there a special tool or some trick to this? If push comes to shove, I can cut the connector (assuming I can get a replacement), but would rather not.
Also, any particular trick to disconnecting the cable to the parking brake lever at the wheel? With that huge spring between the cable bracket and the end of the lever, I haven't been able to move the cable end enough to disconnect it from the lever. Since I don't have the intermediate cable disconnected, could that have something to do with it?
I'm working on an '05 F350 King Ranch dually, and I'm pretty sure the pb cable is stretched. I recently replaced the shoes in the pb assembly and adjusted the tension while I was in there, but it still barely holds. My next culprit sounds like a stretched cable, and I have a complete set for a new one, but I'm having a hell of a time getting the old one out. The link that holds the front and intermediate cables together won't pry open with any tool I have, and I've broken two drill bits trying to drill out the nub holding the front cable in.
View 5 RepliesI have a 94 ranger 4.0 4x4. One winter while 4 wheeling I happened to get into some snow that just kept getting deeper until i got stuck, So i had to back out, after doing that i noticed that the brake light and the abs light were on, then for about a year after that it would just come on and go off. For the past 6 months it has stayed off until you press the brake all the way down to the floor , then it comes on. If you shut off the truck and restart it it will be off until you press the brakes all the way down again. if you get the light to come on and drive with it like that, then when you shut it off and turn it on it will still be on and wont come off until the truck cools down. there is nothing wrong with the brakes, new calipers, new pads, and no leaks that i've noticed. I was told the rotors look a little thin though. I don't know if this is related, but it seems when you start the truck after driving it with the light on, it will idle rough or even stall. but after you rev it 3-4 times it will run smoothly.
View 14 RepliesOf course the month my inspection is due, my e-brake light comes on, and I have no clue why. I use my ebrake religiously.
View 12 RepliesHaving a problem with the brake lights. When the brake pedal is pressed, the running lights (including dash lights, parking lights, and the low power filament in tail light) turn on, but no brake lights. When the lights are turned on and brake pedal is pressed, the brake lights do not turn on at all. The 4 way flashers and signal lights work correctly with lights on and off. Things I have tried:
Replaced the tail light bulbs.
Checked fuses (#5, #10).
Disassembled the brake switch and bypassed it with a jumper wire.
Checked the grounds (tail lights, rear ground, drivers inner fender).
Tried to trace the wiring. Didn't see any noticeable damage, but the wiring is in a loom so it is hard to see.
Used contact cleaner on brake switch, rear wiring harness, body harness.
Still hoping it may be something simple that I've overlooked.
Under mild-heavy braking, the rear brakes on my ranger lock up... EVERYTIME. Not just when its wet, or humid. Everytime I hit the brakes hard they lock. I think I'm getting little, to no pressure to the front brakes either. Could it be just a Proportioning valve?
Truck is a 94' 4.0l V6, RCLB, Auto, 4X4.
I've got a 97 Ranger that popped a brake line. The rigid line burst above the rear axle, in the section that comes from the frame rail to the flexible "down" line.
Trouble is, the rigid line that burst disappears between the frame rail and the fuel tank and then comes out a DIFFERENT SIZE where it goes into the proportioning valve.
Looking for a diagram of that line as it travels forward along the frame rail or know where it changes size?
Yesterday, I noticed that my right front brake caliper seemed to be sticking. This morning I jacked up the front end, and could barely turn the right front wheel when it was off the ground. So, I have concluded that that caliper is sticking. So, here is the question(s): what is the best way to repair this (new caliper, rebuilt caliper, or rebuild it myself), do I need to do both sides the same or can I just do the one that is acting up, and should I expect to pay. I have some mechanical ability, but that Haynes manual doesn't make too much sense to me. Getting it professionally repaired is extremely inconvenient, I need to be back at school (300 miles away) Tuesday evening, and probably couldn't get it in to get it done before then.
View 12 RepliesIt is a 1994 Ranger XLT, Regular cab, two wheel drive, manual transmission and I think it has rear ABS. A front brake line blew which drain the master cylinder. Also a couple of pieces of brake line at the rear had to be replace along with the rear wheel cylinders. After installing the new brake system components we were trying to bleed the system. After reading the repair manual I had it said that vehicles with rear ABS you are to bleed the ABS module before bleeding the rest of the system. There is a module where the book described it (driver's side inside the frame rail) with brake line running to it. I am assuming this is the rear ABS module? I didn't see anything that looked like a bleeder on the module. Where to look? Also when I open the bleeders on the rear wheel cylinder no brake fluid came out.
View 14 RepliesDid a complete rear brake job on a 90 Ranger including a pair of Pronto brake drums. Here are some videos of the problem.
Wheel and tire with new brake drum. Bad wobble.
Wheel and tire with brake drum - YouTube
Wheel and tire installed without brake drum. No wobble.
Wheel and tire without brake drum - YouTube
Brake drum only. Bad wobble
Brake drum - YouTube
Bare axle. No wobble.
Bare axle - YouTube
So is it safe to conclude the brake drum is bad? The other side is worse. I cleaned the axle surface so its flat. Wheels and tires are new.