Ford Ranger / B-Series :: 1999 - Clunking On Deceleration?
Dec 20, 2012
I have a 1999 ranger 4x4 with a 3.0. automatic, extra cab.
I have noticed that sometimes (this has happened twice so far) on slowing down, (just letting off the gas) it will make a large clunking popping noise like you hit a large pothole and bottomed the truck out (or if you had hit a small animal) However, both times nothing was in the road way and no damage was done to the truck. both times it has been in 2high.
The truck does not swerve, grab or anything funky other than make a loud CLUNK every now and then.
This has happened when you let off the gas at about 25mph and coast along. (it may be when you apply gentle throttle to keep rolling, but I can't remember, I was not driving the truck this time, the first time it happened was several weeks ago and I put it off as a freak happening). I will check the usual suspects, u joints, ect, but I was wondering if there could be something else happening...vperhaps something in the front diff? or transfer case? It kinda felt like it came from the front of the truck.
View 4 Replies
Advertisement
I am considering purchasing a 1999 4x4 ford ranger. The original owner has receipts for everything done on it recently. Rebuilt transmission, New ac, New shocks, new tires. I have never owned a ford but I always loved my friend's ranger. The only problem I had with it was an occasional clunking/rattling noise when test driving. I have read and was told this can be a common problem.
View 1 Replies
On deceleration with the brakes (not coast to slow) I get a growling. Sometimes a bit worse than others. Seems to get worse coming up to about 20mph from speed. No other time. I was thinking front wheel bearings as the load up from deceleration. But I just jacked it up and could not find anything that felt or sounded wrong. No play or grind or "bad" feelings in either of the fronts. Front end recently rebuilt, new tires too.
View 9 Replies
There is a clunking sound and feel from the front end of my 2007 Ranger FX4 when in 4 wheel drive. This happens sometimes but not always on engaging or disengaging 4 wheel drive, as well as sporadically while driving along. I took it back to Ford on warranty with this problem last year, and after a few attempts I had them admit that something was wrong and they finally diagnosed that it was the front drive shaft that was binding where it leaves the transfer case, this was replaced. I have now put maybe 50km (max) on in 4 wheel drive and the problem is back, I don't think the problem was ever fixed.
View 14 Replies
first off my truck is 2001 ford ranger 4x4 with an auto. transmission. when I'm driving around in 2wd, everything is fine...
when my 4wd high is on, and I'm starting from a deadstop my truck makes a weird "clunking" noise in the front end. If I'm stuck in mud or snow, and I give gas it keeps "clunking". where the problem comes from?
View 3 Replies
I have a 1986 Ford Ranger that the battery light comes on and all lights get bright at 900 rpm on acceleration, and all lights dim and light goes off at 900 rpm on deceleration. I have replaced the battery, alternator and starter since getting the truck. I have also run ALL the wiring and found only 2 breaks which were repaired. I have had to replace headlights 3 times in two weeks, due to them blowing.
View 5 Replies
I went to transmission shop today and tech told me c solenoid was showing performance problem when scanned. He took it for drive and said it was commanding shift into fifth gear. It is a 3.0 extended cab 2wd with just over 200000 on truck, transmission was rebuilt just over 25000 miles ago. Fluid is so clean its still clear looking just faint red color. All other gears shift and pull great all electrical clean and hooked up, he crawled under it and said pan adjustments were tight, whatever that means.
View 14 Replies
My 99 ranger has a strange issue its got a miss when the A/C is on, when going down the road I can feel the engine sorta pulse for a second, gets better the more I drive it, its got all new plugs and wires, not sure where else to look?
View 1 Replies
Just purchased a 1999 4.0L 4WD, when I select 4WD Hi or LO sometimes it will go, sometimes it won't. Now the 4WD Hi and LO lights are flashing intermittently while I'm driving. At one point the Hi light burned and wouldn't turn off.
View 14 Replies
Okay here's the story I bought a 99 Ford Ranger with a bad 4.0 engine. I had a newer 2002 4.0 and tranny out of another Ford Ranger thought it be an easy swap put the newer engine in and it will only run on the original Older ecm (but ruff) and the older ECM is screwing with the transmission (no reverse) unplug connections at tranny and i have reverse. So I buy a ECM from a junkyard for the 2002 and drop it off at the dealership to have the Pats programmed. and the dealership says they can't program it to make it run. They say the Pats are different from 99 to 2002. So I go another route I buy an SCT performance chip and have them disable the Pats. still won't run.
View 14 Replies
My aforementioned ranger does not seem to heat up. Unless it is 95 degrees in the shade.... I have movement in the dash meter. Some - it will come off of the bottom - to not quite the c - then immediately dive back to less than cold ( which I realize is not possible) - engine seems to run fine. Use 93 octane or it knocks like a diesel. 135 K - I changed the thermostat. Less movement on gauge now than Before. Coolant level is fine. I read something in another post about the blend door. But my engine temperature doesn't even seem to be getting warm so how would the blend door be effecting that? I am an electrician not a mechanic, however I do all my own mechanic in in self defense. Since I cannot afford mechanics.
View 9 Replies
I drive a 1999 ford ranger and can't figure out why my 4x4 won't engage. I have vacuum all the way down to the hubs and when I turn the switch it sounds like the transfer switch is engaging but the 4x4 still doesn't engage. What do you all think could be the issue? I thought about just putting a set of the manual locking hubs on it and just be done with it.
View 1 Replies
I have a 1999 Ranger 4x4 4.0 5 speed step side...in Jalapeno no less. Anyway, for the past 5 years or so the check engine light has been on. When it came on I did nothing because nothing seemed to change and I was too broke to fix it anyway. Well, just lately the check engine light has started to flicker or go out completely.
When this happens the truck seems sluggish and the A/C will stop working. As long as the check engine light is ON the truck runs like it always has, when it goes off the issues start. If I am stopped with the clutch depressed the idle will drop down to 500 rpms or so.
Kinda hoping it is something I can fix or at least learn about so I can have an intelligent conversation with a mechanic.
View 6 Replies
Will move if n 4low and give some rpm's. Reverse is fine, disassembled and clutches look fine.
View 1 Replies
Yesterday my 1999 Ranger 2.5L Automatic got really wierd! The check engine light came on, the overdrive light started flashing, the ABS light came on, and the transmission can't shift out of low, except manually...and to top it off the speedometer quit working! What the heck is going on???? This has got to be all connected somehow.
Up until now, I have had no problems. The truck has about 45K miles. I change the oil at 3-4,000 miles and try to take care of this as my teenage daughter drives this truck to school.
View 14 Replies
I have a 1999 Ranger XLT 4.0 . The air is on all the time no matter what position the selector switch is in except "off ".
View 4 Replies
[URL] ... Looking for info on my 99 Ranger.
Here's what happened,I have an electric plow I hook to my Ranger every year with no problems,except this year. The day after hook-up my wife noticed no high beams, don't know if the two are related but I did nothing but connect the plow wires already in place. Anyway I proceeded to look for a fix, fuses first, replaced both headlights next, blinker/high beam/wiper lever-still no fix and to boot my truck doesn't ding when keys in ignition, four wheel switch doesn't work, & wipers don't work.
View 10 Replies
So my 99 2.5 rcsb has been stalling out under loads, particularly when the A/C is on. It's stalled when warm, cold, engaging Drive or Reverse, and it steering does it at least once a day. There's a missing elbow to a vacuum line at the driver side (looks RABS related). The truck had the CAT melt off and now it's laying in my bed with the O2 sensor, don't know if that relates.
This truck sees 100 miles a day through the mountains, 5-7 days a week. It only has 140,000 miles on it, I put 40,000 on it in the last year with no issues. The truck is very much showing age (needs almost everything), but I'd like to keep the basics going.
View 14 Replies
I have a 1999 Ford Ranger XLT and it has been getting wet inside and I would like to get this fixed, but have no idea of where the water is coming in at.
I also noticed that at time there is allot of moisture in the inside on the windshield, have no idea where that is coming from?
Also if I have my Floor Mats in and left them up it will be wet under them NO matter if it is Winter or Summer, so I took them out.
Also I have noticed that behind the seat on both side it gets wet and I have that window that you can open in the middle, would it be coming from there?
Also what would cause the doors to freeze and you have to pull as hard to get them open in the Winter time, are the seals bad on the doors?
View 5 Replies
I just bought a 99 Ranger 3.0 L. Truck runs great while cold. After it warms up however it has a misfire. I knew that when I bought it, and bought it cheap enough that I figured even if its down on compression or something serious, I could afford to throw a long block in it. It also is throwing a check engine light. I have not read the codes yet, waiting on a scanner I purchased. Ive got new plugs and wires for it, not yet installed. Also, have not checked compression yet. Been too busy to work on it much so far. Just curious if there is anything I can look at before the new scanner arrives.
View 8 Replies
Ok, went out last night to go over to a buddies place to watch some football. Tried to start my truck but all that happened is that it would turn over, but not start. Had plenty of juice in the battery, and 1/2 tank of gas. It acted like it wanted to start, but nothing doing - just keeps cranking and cranking. Its even more frustrating because I was driving it around most of the day before this happened.
Here's the dillema: Its been doing this for the past two months now on and off. Once I fix something, it runs for about a month, and then it starts doing this again, without any warning signs (i.e. multiple cranks before a start, stalling, hesitation on accel., etc.). At this point I'm clueless. I've replaced the fuel filter, fuel pump, and air filter, but the problem has resurfaced again.
An interesting thing to note is that the only ways I'm able to get it started when it starts doing this is to remove the electrical connection from the intertia switch, and crank the engine a few times to relieve the fuel system pressure. After reconnecting the inertia switch, the truck starts instantly.
So whats the deal? Why this would work, and why suddenly the thing would not start after weeks and weeks of driving flawlessly? Is it possible that my system is either too pressurized or losing pressure somehow, and that is how it be able to start? A buddy suggested it might be injectors, but I'm not so sure, because there is no hesitation on accel or performance loss, or even a rough idle.
View 14 Replies
