I drive a 1999 ford ranger and can't figure out why my 4x4 won't engage. I have vacuum all the way down to the hubs and when I turn the switch it sounds like the transfer switch is engaging but the 4x4 still doesn't engage. What do you all think could be the issue? I thought about just putting a set of the manual locking hubs on it and just be done with it.
View 1 RepliesI bought a 99 ranger few months ago cant the 4x4 has not worked in the truck for about 4 years. Bought it off my dad. He hasn't figured it out the t case locks in the drive shaft spins but hubs will not lock in. Has new hubs in it and still not working. Trying to get it fixed so I can park the diesel for the winter and run the ranger.
View 3 Replies97 automatic 4x4 SXT 4.0L. 4Hi will engage, but when I shift to neutral, press foot on brake, and shift to 4lo, nothing happens. No light, no sound. Occasionally it will make a sound, and even more rarely will light up, but it does not feel like 4Lo is engaged even when indication says it is. I pulled the shift motor and replaced, as well as verified that the transfer case could be shifted to 4 hi and lo by using an adjustable wrench. I have not put truck on stands yet, but I'm pretty sure 4 hi is truly engaging. I did attempt to engage with shift motor connected electrically but not mechanically, and it shifted. What is keeping 4 Lo from shifting? If it's a vacuum issue, wouldn't 4 hi not shift? I did check the vacuum lines and the vacuum reservoir and they seemed to be okay.
View 3 RepliesI have a 1999 Ranger 4x4. My 4wd does not engage when I turn the switch to 4wd lo or 4wd hi. The lights on the dash flash on and off. I disconnected the battery and now the lights are clear. But if I try again to engage it, the lights return. I feel I have a vacuum issue but would like to know more about locking hubs. If I convert them over, how do I know that my system will work? There has to be something else that changes from 4wd lo to 4wd hi. How do I check to see if this is working properly.
View 6 Replies1987 ford ranger loaned it out and they said the hub spins on the driver side but the tire won't engage so it has no 4 wheel drive. Soon as I get it back hopefully today will know more.
View 14 RepliesI bought a 2000 Ranger 4x4 3.0L auto today from the neighbor guy sight unseen with a "bad tranny" for $400. I'm very unfamiliar with the Ranger family, but long story short:
When moving the shift lever, the trans doesn't engage. It needs to be engaged from underneath. Do the cables tend to stretch, or break? I can't find any adjustment on it anywhere.
So I just had my entire clutch replaced while another repair was taking place. What I've noticed is the "clutch engagement" has changed. Where as I would have the clutch start to engage/disengage at the 1/2 way point on the pedal travel is now the last 1/4 of the pedal. Is this a "normal reaction to a new clutch that just takes getting used to or is there an adjustment I can fine turn it with? Do I just have to wait for it to "break in"? When I replaced the clutch on my dearly departed 94 ranger, I replaced the bearings & disc only reusing the pressure plate and did not have this issue.
View 3 Replies1999 Ford Ranger 2.5L 5 speed transmission. I am a little confused I can not get the transmission to engage the clutch, I replaced the clutch 3 weeks ago, now I have no pressure in the pedal, I have bleed the system 5 attempts with clean solid flow of fluid. What else can I do to fix this or trouble shoot from here?
View 6 RepliesI went to transmission shop today and tech told me c solenoid was showing performance problem when scanned. He took it for drive and said it was commanding shift into fifth gear. It is a 3.0 extended cab 2wd with just over 200000 on truck, transmission was rebuilt just over 25000 miles ago. Fluid is so clean its still clear looking just faint red color. All other gears shift and pull great all electrical clean and hooked up, he crawled under it and said pan adjustments were tight, whatever that means.
View 14 RepliesMy 99 ranger has a strange issue its got a miss when the A/C is on, when going down the road I can feel the engine sorta pulse for a second, gets better the more I drive it, its got all new plugs and wires, not sure where else to look?
View 1 RepliesJust purchased a 1999 4.0L 4WD, when I select 4WD Hi or LO sometimes it will go, sometimes it won't. Now the 4WD Hi and LO lights are flashing intermittently while I'm driving. At one point the Hi light burned and wouldn't turn off.
View 14 RepliesOkay here's the story I bought a 99 Ford Ranger with a bad 4.0 engine. I had a newer 2002 4.0 and tranny out of another Ford Ranger thought it be an easy swap put the newer engine in and it will only run on the original Older ecm (but ruff) and the older ECM is screwing with the transmission (no reverse) unplug connections at tranny and i have reverse. So I buy a ECM from a junkyard for the 2002 and drop it off at the dealership to have the Pats programmed. and the dealership says they can't program it to make it run. They say the Pats are different from 99 to 2002. So I go another route I buy an SCT performance chip and have them disable the Pats. still won't run.
View 14 RepliesMy aforementioned ranger does not seem to heat up. Unless it is 95 degrees in the shade.... I have movement in the dash meter. Some - it will come off of the bottom - to not quite the c - then immediately dive back to less than cold ( which I realize is not possible) - engine seems to run fine. Use 93 octane or it knocks like a diesel. 135 K - I changed the thermostat. Less movement on gauge now than Before. Coolant level is fine. I read something in another post about the blend door. But my engine temperature doesn't even seem to be getting warm so how would the blend door be effecting that? I am an electrician not a mechanic, however I do all my own mechanic in in self defense. Since I cannot afford mechanics.
View 9 RepliesI have a 1999 Ranger 4x4 4.0 5 speed step side...in Jalapeno no less. Anyway, for the past 5 years or so the check engine light has been on. When it came on I did nothing because nothing seemed to change and I was too broke to fix it anyway. Well, just lately the check engine light has started to flicker or go out completely.
When this happens the truck seems sluggish and the A/C will stop working. As long as the check engine light is ON the truck runs like it always has, when it goes off the issues start. If I am stopped with the clutch depressed the idle will drop down to 500 rpms or so.
Kinda hoping it is something I can fix or at least learn about so I can have an intelligent conversation with a mechanic.
Will move if n 4low and give some rpm's. Reverse is fine, disassembled and clutches look fine.
View 1 RepliesYesterday my 1999 Ranger 2.5L Automatic got really wierd! The check engine light came on, the overdrive light started flashing, the ABS light came on, and the transmission can't shift out of low, except manually...and to top it off the speedometer quit working! What the heck is going on???? This has got to be all connected somehow.
Up until now, I have had no problems. The truck has about 45K miles. I change the oil at 3-4,000 miles and try to take care of this as my teenage daughter drives this truck to school.
I have a 1999 Ranger XLT 4.0 . The air is on all the time no matter what position the selector switch is in except "off ".
View 4 Replies[URL] ... Looking for info on my 99 Ranger.
Here's what happened,I have an electric plow I hook to my Ranger every year with no problems,except this year. The day after hook-up my wife noticed no high beams, don't know if the two are related but I did nothing but connect the plow wires already in place. Anyway I proceeded to look for a fix, fuses first, replaced both headlights next, blinker/high beam/wiper lever-still no fix and to boot my truck doesn't ding when keys in ignition, four wheel switch doesn't work, & wipers don't work.
So my 99 2.5 rcsb has been stalling out under loads, particularly when the A/C is on. It's stalled when warm, cold, engaging Drive or Reverse, and it steering does it at least once a day. There's a missing elbow to a vacuum line at the driver side (looks RABS related). The truck had the CAT melt off and now it's laying in my bed with the O2 sensor, don't know if that relates.
This truck sees 100 miles a day through the mountains, 5-7 days a week. It only has 140,000 miles on it, I put 40,000 on it in the last year with no issues. The truck is very much showing age (needs almost everything), but I'd like to keep the basics going.
I have a 1999 Ford Ranger XLT and it has been getting wet inside and I would like to get this fixed, but have no idea of where the water is coming in at.
I also noticed that at time there is allot of moisture in the inside on the windshield, have no idea where that is coming from?
Also if I have my Floor Mats in and left them up it will be wet under them NO matter if it is Winter or Summer, so I took them out.
Also I have noticed that behind the seat on both side it gets wet and I have that window that you can open in the middle, would it be coming from there?
Also what would cause the doors to freeze and you have to pull as hard to get them open in the Winter time, are the seals bad on the doors?
I just bought a 99 Ranger 3.0 L. Truck runs great while cold. After it warms up however it has a misfire. I knew that when I bought it, and bought it cheap enough that I figured even if its down on compression or something serious, I could afford to throw a long block in it. It also is throwing a check engine light. I have not read the codes yet, waiting on a scanner I purchased. Ive got new plugs and wires for it, not yet installed. Also, have not checked compression yet. Been too busy to work on it much so far. Just curious if there is anything I can look at before the new scanner arrives.
View 8 Replies