Ford Ranger / B-Series :: 1998 - Turn Signal Flashes Intermittently Then Stop - Indicator Flasher SF631 Location?
Mar 18, 2017
So with 172,000 miles my truck has started a new trick. When I turn on the turn signals theyll flash or interrupt normally for a few times then stop. After I turn the signal lever off and back on again they start to flash again only to stop after several times. This happens to both the left and right hand sides. The emergency flashers seem to work alright. Is this a function of the indicator flasher SF631? If so, were exactly is it located?
View 5 Replies
Advertisement
2015 prius package 5 w tech package and HUD display, I found a flasher mounted up between the fuse box/ module assembly mounted on a clip! I have a led replacement flasher, but clip mounts and pin locations don't line up? I watch the video but I have nothing in area! Or I just need to install the resistors? Or it could be a combination circuit assembly where multiple function module all in one ?
View 1 Replies
Exactly where that part is, pictures would be useful. Pretty much just had my whole dash apart with no luck. Switched to leds, and can't stand hyper flash like I thought I could. Trying to pull it to make sure I order the right part to correct it.
View 11 Replies
Where is the signal flasher relay located. I can hear it but can't track it down.
View 5 Replies
98 Ranger 4x4 4.0 L Supercab. Today I replaced my instrument cluster lights. When I put everything back together i noticed my gear shift indicator is off and I cant shift into 1st or 2nd. What did I screw up?
View 5 Replies
I towed my friends car hauler yesterday for a short distance for him. I had no turn signals or 4 way flasher while towing. After dropping off the trailer still no signals or 4way flasher. I parked and checked fuses all were good and signals started to work. But still no 4ways. Any thoughts on what to look for. Never had this before. I have blown a fuse before and always been able to find and fix.
View 13 Replies
My interior right turn signal light wont come on. The right exterior bulbs work fine. I swapped the bulb with a new one and it still doesnt come on. Could the socket be bad? Should I have sprayed the cluster bulb socket with contact cleaner?
View 4 Replies
My 97 F150 4X4 's turn signal flasher buzzes all the time except when brake is depressed or turn signals or hazard signals are active. The flasher is a 5 prong one. What to check?
View 9 Replies
I'd like to put in a louder turn signal flasher on my 2007 F150 - where is it located and where I can get a louder one ?
View 1 Replies
Turn signal flasher doesn't work in the heat. What gives?
All lights work. Turn signal stalk works fine. It just flashes a couple of times, then stays on. Everything works fine in cool weather, but it rarely works at all when the temperature outside is above 90 degrees. Very annoyed.
View 4 Replies
99 Ranger XLT 4.0 4WD Automatic. With the turn signal blinking and I depress the brake the turn signal stops blinking until I release the brake. Where to start.
View 2 Replies
I have a '97 AWD and my brake light, turn signals and emergency flasher have stopped working. I've checked all the bulbs, checked all the fuses (under the dash) replaced the flasher just in front of the fuse box...nothing. All the running lights work, and the 3rd brake light above the rear door window works.
View 3 Replies
I'm having an electrical issue that is driving me nuts. I have an '01 F-250 Super Duty that I just put a new battery in today. The truck normally runs great, I drive it to work everyday with no issues. Today, there is a noise coming from under the dash that sounds like the turn signal flasher, and the clock on my radio flashes in time with the noise from under the dash. All my lights are working ok, and all the idiot lights come on as usual when I put the key in the ignition and turn it to the on position. However, my truck won't start. It won't even turn over. I get nothing but a dead switch when I turn it to the start position. The starter solenoid doesn't even click. Like I said, yesterday everything was just fine. I knew my battery was going bad (6 years old), so I changed it.
View 4 Replies
I want to install some LED turn signal bulbs and lights but the flasher will flash twice as quick because of the burnt-bulb detector.
I have taken the flasher apart and tried all the tricks on the book to isolate each pin on the IC and changed the timing resistor without avail. I do not want to put in load resistor on the bulb end to fool the detection circuit.
I want to modify/cut off the detection circuit?
View 14 Replies
I have an '07 Azera and the turn signal sound is intermittent. The signals flash normally, but sometime I hear the flasher sound inside the car and sometime it is dead silent. Cannot seem to correlate it to temperature or other factors. Any way, I assume as the lights flash with no sound that either the flash or the sound is electronically generated, but cannot be like an old school mechanical flasher. What makes the flasher sound in the Azera and where is it located?
View 1 Replies
1998 Ranger, 3.0 liter manual transmission. The vehicle recently has had the engine replaced. Still a 3.0 Liter, but possibly is from a 1995 or 1996 Ranger. Replacement motor from a wrecking yard, appears to have been sitting for quite some time prior to purchasing. I had a friend change the motor out after getting the vehicle a few weeks ago.
Ranger drove fine for a week, but this morning it wouldn't start. One click is all it would give when you turned the key. Thinking the culprit was the all in one starter/solenoid, I replaced it with a new one this morning. Now the solenoid will click continuously when the key is turned, starter still will not rotate then engine.
Battery tests good - 12.4 volts; connections appeared fairly corroded.
Here is what I have done:
- Clipped off the first half inch of corroded terminal leads, replaced both sides with new battery connectors and wire brushed connections off at battery and starter.
- Replaced Starter
- With "S" connector disconnected, attempted to bypass starter connections and short terminals to see if a faulty clutch position sensor was to blame; shorting did not produce anything other than turning the key did.
- Paralleled an additional cable from battery to starter terminal to see if corroded wire connections were to blame; still just clicked repeatedly when attempting to start.
Crankshaft does rotate manually, does not appear to be seized up. Unsure of what else to check for. Not confident in friend's engine installation abilities, he may have screwed up something I'm not thinking of. On the other hand, I don't believe I would have been capable of swapping out the motor myself.
View 3 Replies
98 4wd extended cab. So weird only the right side is not working. Lights in the dash to the lights outside everything is dead.
Fuses that I could find are good. We replaced the mf switch a few months ago.
View 2 Replies
The turn signals and high beams do not work on my 1998 ford ranger xlt 4x4. I have replaced the multi function switch, the yellow flasher relay checked all fusses and all are good. What could be the problem?
View 7 Replies
I recently got a pretty cherry 98 Ranger 3.0 2wd extended cab auto. So far all it has needed was wiper blades, floor mats and a heater blend door. Last week my daughter informed me that the flashers and the turn signals stopped working. I looked for blown fuses and then took the low road and just bought a new flasher (my alldatadiy manual showed that the flasher was common to the turn signals and the hazard flashers so I took a shot at just throwing a part at it). That didn't fix it or else. Any pointers?
View 3 Replies
What is the easiest way to change the flasher?
View 6 Replies
I have a 72 F250. When I put the left turn signal on and apply the brakes, the signal stops blinking. I checked the bulb and it was fine. What is the likely cause?
View 2 Replies