I understand there is not much adjustable on my 98 Ranger (2.5L) as far as idle speed and mixture. It runs rough when started cold. Is this a sign to replace spark plugs?
View 2 RepliesThrowing codes ... p0136, p1131, p1151 acts like it going to just stop then will take off, at a stop light it will sound like it has a large cam in it... It is a 1998 4.0 V6 automatic tranny.
View 1 Replies98 ford Ranger 2.5L.
I have not heat from the vents, doesn't get warm at all. If I idle the enginer in 30 Degree weather it gets to almost the C.
Upper Radiator hose is hot, I have verified the thermostat is new and it opens at 192 degrees as it should. Replaced the Water Pump, Fan spins freely.
I have attempted to burp the system, it isn't kicking out anymore air from the lines that I can tell. I used a large funnel and filled it with Anti-freeze, it filled the radiator, burped the system and the reservoir filled to overflowing. All with the engine hot. (To be specific the funnel was always full of fluid so no air could get sucked backwards)
The heater core hose on the left when looking from the front of the vehicle does not get hot, the one on the right gets warm. I theorize that the heater core is clogged up somehow and that is why that left line doesn't get hot. There is no fluid in the cab of the truck from the core.
1998 Ranger 4x4 4.0 Ltr - Runs rough ever now and then and CEL giving P1151 code. Upper and lower intake gaskets have been replaced.
View 14 Replies1998 4.0 ... She only misses about 30 seconds during stone cold startup. I figure it's probably the plug thats hardest to reach ? Isn't that the way it always is? From the hood I can see only one spark plug, so I figure I'll do all the plugs. Is there any right or wrong approach to the plugs? I did the thermostat today, but this plug job looks like it's gonna be a bitch. Time for some skinned knuckles Next is the right side O2 sensor, that looks like fun too. But I gotta say, this little truck is sweet. Great visibility and easy to park in the city. I really like her. She's a keeper. She needs some new sway bar bushings too, but no surprise with 127 K on the clock.
View 5 RepliesI have a 98 ranger with 2.5 and 225k mostly trouble free miles. This engine has never used a drop of oil and ran good. In Dec 3 miles from work started running poorly and sounded to knock the more I asked for power. The CEL started flashing I made it to work and it idled rough but more rpms smoothed out. Took it to mechanic says he did a compression check with little or no compression on #1 & #2. #3 & #4 fine must have broke rings. Doesn't seem right to lose 2 cylinders at the same time out of the blue. Could anything else be causing these symptoms or time for a heart transplant? He hasn't opened anything up yet.
View 6 RepliesEngine runs rough at idle. Two plugs are black and just replaced head gaskets. I installed new short block and new heads six months ago. I can't seem to figure out the problem and I would like to trouble shoot more before tearing heads off and going any further.
View 2 RepliesWhat would cause my 4x4 high and 4x4 low lights to flash intermediately together on cold mornings while driving? It won't switch into 4x4 when it does this either. When it sits and warms up later in the morning all works as should. It doesn't do it all the time but when it does its annoying not to mention it's sucks when I need 4x4.
View 1 RepliesI’ve got a 1998 Ranger with 166,000 miles and it’s starting this weird idle at stops where the engine drops about 150 RPM’s and then fluctuates. The problem is intermittent and no pattern as to cold or warm engine. I changed the plugs and wires at 100,000 and the plugs again at 150,000, so the wires have 66,000 and the plugs 16,000. I really don't want to shotgun the plugs, wires and coil pack. I understand that vacuum might have something to do with my problem?
View 14 RepliesThis has been an ongoing issue for about a month. When I start the engine after it has been sitting and is cold it runs ruff for about a minute then smooths out and runs fine. I pulled a P0304 code (cyl.4 missfire) but I do not get a CEL.
I checked the plugs and they were ok but I changed them and the wires anyway as it just turned 50k and the plugs were original. I could live with a little cold ruff idle but the code throwing bothers me. The truck is a 2000 xlt 4x with auto trans. and 4.0 engine. This is my second 4.0 ranger but I have only had it for about 6 months.
I'm getting tired of the same problem about every 6 months. Plug #4 keeps going bad. Its been doing this for years. It starts with rough idle when first starting up that clears up quickly then eventually it leads to a misfire when accelerating. Every time this happens I replace plug #4 and its good to go. Just recently (roughly 6 months ago) did a full tune up and all new injectors. About a week or 2 ago it started its rough idle at start up and just the other day it started misfiring again. What would keep causing this??
View 14 RepliesMy 2005 2.3l Ranger ran great. I moved a trailer about 150 feet and stalled the truck backing it up. Stick shift. Unhooked the trailer and pulled back into the parking area....all the sudden the truck has extremely rough idle and stalls. It runs good on the highway. AutoZone ran a OEM number to cross: P0171.
I cleaned the IAC with intake cleaner. No Luck
I unhooked battery for 15 min. No Luck
I sprayed intake with 1/2 can of intake cleaner. No Luck
I did not have a tamper torx to remove the MAF. What next.
168K, to date, replaced
rear 2 cat's
Timing chain and gears
cam sync assem.
Plugs, wires, dis block,
Why.............. Read on
This 2003 ranger 3.0 v6, run very hard at idle, yet it runs and you can drive it around town, ""at"" low rpm, and no hills but it gets from point a to point b
I have no pre ingintion, but a plug that was only 60 days only was burnt out completely on 3rd cyl. bank 1 or as ford call it #3, i am telling you this thing seem like it running on 4 cyl,s kicking back and forth, and replacing everything above made no difference.
On the highway, as long as it is flat or down hill 75-80 mph, as soon as a hill or power to pass is needed it bogs down and slows it self to about 45 mph, I have been though everything i can think of and my next move to to start pulling heads, but i wanted to ask here first.
I have a 2002 ford ranger xlt 3.0 i just rebuilt the entire motor about a month ago and was having a high idle problem for the longest time. turns out i had the iac on backwards. but now that it idles down around where its supposed to it has a rough idle has a little shake to it. starts up right away but when i drive down the road around 3000-3500 rpms its missing on cylinder #3 from what the code I am getting "multiple cylinder misfire, #3 cylinder misfire" I've replaced plugs and wires. camshaft pos sensor. I am getting 65 lbs of fuel pressure. spark on all cylinders. I am really at a dead end here. Also every time I take the plugs out to look at them they look brand new.
View 14 RepliesSo I have a 2001 ranger 2.3l . Runs very rough at idle.code says misfire in cyl.#1. I have changed plugs, wires, coil packs all motocraft. I did a compression test..
#1.170
#2 180
#3. 185
#4 . 180
Compression seems fine,but where do i go from here? Anything else i can check/replace to solve this?
1999 B3000 with a 3.0. The truck idles at 850rpms. When it starts it idles at around 1000 and runs very rough. When I disconnect the IAC the engine dies. The AC also has problems it blows cold at idle but at highway speeds after 7-8 minutes running the compressor kicks out. One can turn it off and it blows cold again after a few minutes.
View 5 Replies2007 Ranger 4.0l, idles rough at low rpm, in park or drive, with or without the AC on.
View 1 Replies1995 ford ranger with 4.0. It idles rough. Replaced MAF TPS fuel pump fuel filter fuel pressure regulator upper o2 sensor. IAC.. still idles rough RPMs drop. It isn't as bad since replacing MAF but still not right. What else is there.. Cleaned out the air intake port it was gummed up. Don't know what else to do?
View 3 RepliesI have an 02 ranger xlt 3.0, it started having a rough idle, codes say cylinder #2&3 misfiring, changed plugs, wires, coil pack, didn't work, still same code, checked injectors on right side, all 3 had ohm reading of 15.8-16.5, the injectors were clicking like they are supposed to, sprayed carb cleaner around the intake ports, didn't change the idle at all,what else can I check or do? with out tearing the engine apart, unless of course I have to, the truck has been very good to me, it's got 205,000 miles on it, I need it to last at least another year...
View 4 RepliesI have a 1999 B4000 4.0L with 160K miles on it. Bought the truck new. Up until about a year ago it ran perfect but has developed an idle, stalling and occassional jerky ride problem. It occurs at any temperature, engine hot or cold, A/C clutch on or off and in Park, Drive or Neutral. When you start the engine it will not idle unless you keep your foot on the gas. The idle speed will drop to 200-300 rpm and the engine dies. Sometimes you can barely tap the gas pedal and the rpm will shoot up to normal idle speed (about 900 rpm) and stay there a few seconds then begin to drop again. If the engine is cold it will often die a couple times after starting even with the foot on the gas and then about the 2nd or 3rd time run with your foot on the gas.
At stop signs and red lights you have to keep your foot on the gas to keep it running. If you are approaching a stop sign and take your foot off the gas to coast to a stop and brake, the engine rpm will drop and the engine will die. It always starts fine though. Once you are driving it generally runs just fine at low or high speed. You can generally set the cruise control on the expressway and cruise right on. However, sometimes all of a sudden the truck will start bucking and jumping as if it has a terrible misfire. It usually lasts a few seconds and quits. Often if you step on the gas it quits. Even less occasionally the engine will begin to slow as if it is starved for fuel and slow down. You can press the pedal to the floor and it sputters a bit then picks up and runs fine.
I have read about all the threads in this forum and others and tried some of the suggested fixes but it still has the problem. I have tuned it up with new plugs, wires, fuel filter, air filter and PCV valve. Based on some of the forums advice I have replaced the IAC valve, the EGR valve and EGR Pressure Feedback Sensor, and cleaned and inspected the MAF sensor with MAF cleaner. I have checked all my vacuum lines and no leaks there and checked the engine timing which is fine. Fuel rail pressure and engine compression are also fine. Spark plugs show no clues, exhaust is clean and the engine uses virtually no oil. There has been no tear down on the engine like removing the heads, cam, timing gears or any of that and the engine is completely stock.
It shows no codes related to the problem. Two or three months after the problem started I showed a code that indicated an injector problem, traced the problem to a bad injector, replaced the faulty injector and it was fine. That took care of that code but didn't solve the idle problem. In my younger days I was into drag racing and I rebuilt engines, swapped transmissions, etc. and still do my own tune-ups today so I am fairly familiar with auto repair and have most of the tools for testing newer cars but this one stumps me. As a last resort I'm about to take it to the dealer.
I love my Ranger. I'm quite impressed with the power and durability. I'm ticked at Ford for stopping production.
I have searched my problem and could not quite narrow it down. I have also tried several remedies with no improvement. I need to narrow it down to a specific item.
2004 Ranger, 4.0 liter, 4x4, 131,000 miles, runs great above idle.
Problem: rough idle, idles at about 750 rpm's. If i raise the rpm's to 850 and up, smooth as silk.
The truck did this a few years back. Not quite as rough and it went away by itself.
Engine light came on this time with P0303 & P0316 codes. I have replaced: plugs, wires, coil pack. I know that the #3 plug is sparking quite well. the #3 injector is getting signal to spray not sure if it is. I have 4 O2 sensors and I believe I tested them correctly (passed). The passenger side upstream or pre cat sensor has not been tested yet. Had to rent a tool and will do that in morning. I slid a piece of aluminum roof flashing between the crank position sensor and the crank pulley. Not a noticeable difference. While at idle (750 rpm's) I pulled each (#3,2,1,) (one at a time) injector wire plugs off the injectors. No noticeable difference. I pulled the vacuum line off the egg and operated it with a vacuum tool. Seems to be working fine. Sprayed carb cleaner around on vac lines. No engine surge