Ford Ranger / B-Series :: 1998 - Horrendous Shake Upon Startup
Mar 2, 2015
I have a 98 Explorer upon startup is horrendously shakes. What went to hell in the transmission?
View 6 RepliesI have a 98 Explorer upon startup is horrendously shakes. What went to hell in the transmission?
View 6 RepliesSo Im working on a 1998 mazda b4000, frost plug blew out going down the highway changed the engine because it got cooked pretty bad. The wrecker engine I got for what ever reason will only run good if the driver side of coil pack is done 5,6,4 any other order truck wont run at all. Misses enough to shake the truck at around 80 km/hr otherwise its pretty good. Also the engine I got came factory with no egr.... no provisions nothing. exhaust manifold capped off, seemed kinda odd.
View 5 RepliesI have a 98 Ranger SuperCab XLT 4WD 4.0 Auto. Occasionally, especially when it has been sitting for more than 3 days, it shakes for maybe 30 seconds on startup. It smooths out gradually after that, maybe 15 sec. to normal smoothness. It seems like it is firing on all cylinders and is more like something out of balance.
Never does it when sits less than 2 days. When it happens, the longer it sits the worse it shakes.
1998 4.0 ... She only misses about 30 seconds during stone cold startup. I figure it's probably the plug thats hardest to reach ? Isn't that the way it always is? From the hood I can see only one spark plug, so I figure I'll do all the plugs. Is there any right or wrong approach to the plugs? I did the thermostat today, but this plug job looks like it's gonna be a bitch. Time for some skinned knuckles Next is the right side O2 sensor, that looks like fun too. But I gotta say, this little truck is sweet. Great visibility and easy to park in the city. I really like her. She's a keeper. She needs some new sway bar bushings too, but no surprise with 127 K on the clock.
View 5 RepliesI don't have a Ranger or B-Series, but I do have Ford's older B-Series counterpart. 1979 Ford Courier, 2.3L/5-spd. I have had a bad rear end shake since I bought the truck nearly three years ago, so I'm sure it existed well before then. It only happens around 60-65 mph, and there is also a kind of buzzing/humming sound whenever I'm coasting to a stop in neutral. I have:
Replaced and balanced the tires several times
Rotated the tires several times
Replaced all four wheel bearings
Replaced steering linkage
Replaced front suspension
Balanced driveshaft twice
Replaced driveshaft center bearing
Replaced all three U-joints
Checked rear wheel lateral and radial runout
Had the front end aligned three or four times
Checked engine and trans. mounts
And yet the issue persists. I am stumped and this problem is driving me bonkers!
I have a 2003 Ranger 4x4 with the 5speed automatic. It has 215,000 miles on it and I don't drive it regularly anymore. Lately, I've noticed that it will shake after start up for 10-30 seconds. This only happens after it has sit for a few days or a week. After it warms up, I can drive it and stop and start it again and it has works as usual.
Is there some way the convertor is leaking out fluid and it shakes until the convertor is full again? Or is something else the problem. I've changed the fluid two or three times during the life of the vehicle.
1999 ranger 2.5. 135k!So I started with a tune up all motorcraft, fuel filter and air filter. Did nothing! So I did compression check all cyc 150psi and above. So I did leakdown, had air leak at dip stick and valve cover, So I asumed head gasket. Pulled head and found 3 head bolts on passenger side had carbon deposit bluid up really bad, So replaced head gasket all surfaces clean and flat. Still didn't fix it!! My symptoms are better than before hd but still have a engine shake and flashing cel at 55 plus mph and p0303 pending! Coils tested good but going change them any way tonight!I'm stuck on this one checked everything 3 times and then again...
View 7 RepliesTruck spits and sputters when it starts up..and now it does it more often New spark plugs, new fuel pump and filter New mass air flow. I changed fuel octain and that work for a few weeks and back it spits...... It seems that when I put something new in the truck it runs great for a few weeks and then it starts up again...... I can not find a fuel regulator that fits the one that is on the truck now......so I have not replaced it........
View 4 RepliesOn startup, hot or cold, I get an initial high idle, up to around 1800 rpm's. This happens immediately when engine starts, and then idles right down. This has done this since new in '04. Dealer at that time said it was normal and not to worry. It's always made me wonder, but I trusted the dealer. Ya, not always smart.
After 92k miles. Engine runs fine otherwise, but I don't really care for grabbing a bunch of rpm's on any engine without having the oil pressure up to normal.
A few weeks ago, I started it up, and some yahoo said he knew I drove big trucks by the way I started my Ranger. That was one of those times. I'm thinking IAC is wide open maybe?
I have a 97 Splash with the 3.0, oil pressure goes up to about the middle of the gauge after startup, however, it stays there whatever I do, warm/cold, idle/5500 rpm. Is it supposed to be like that?
View 4 RepliesMy ranger has always run pretty good except for a small bit of chattering at startup which quickly went away after it warmed up. Now all of a sudden its much louder and doesnt seem to go away while driving. I read about the oil pickup tube getting blocked and not properly delivering oil and so I performed the superhuman task of dropping the oil pan to check. While I couldnt get the oil pan all the way out, I got it to where I could feel the oil pick up screen and everything seems okay. I have the valve cover off. Are the lifters adjustable? Whats the issue?
View 10 RepliesPreviously on "This Old Truck": [URL] ....
Mileage now 298,5xx. Done since last report: Oil change and filter. Trans oil change (merconIII, no leaks apparent). Tires. Front brake pads. Clutch safety switch (was interfering with cruise control operation) Coolant replacement. (see below)
Rat damage related overheat (near total coolant loss, but no MIL) at 288k. (Rat suffered acute lead poisoning later that night) No sign of rodents since.
Fuel filter change (after onset of symptoms).
NO MIL/CEL, no pending codes. CEL/MIL operates on KOST.
Temps normal (190F +/-2 deg during steady-state cruise operation, fuel flows and fuel mileage have not changed significantly. (fuel mileage has IMPROVED approx 5%, possibly due to gentler/slower driving)
M5OD with Limited slip 3.73/ payload pkg II (1650lbs)
Symptoms:
- Intermittent misfire on startup, seems to get better as the truck warms up. (intermittent= some days it do, some days it don't.)
- Truck starts and idles well, even with misfire.
- Intermittent loss of power, usually worse on days when no- or minor- misfire at startup/cold idle. From the driver seat it feels like accelerating over painted lines on a rainy day. . . a couple revs of no power, then it pulls hard for a second or two, then misses a couple of shots, lather, rinse, repeat.
- Usually worse in higher gears; (not noticeable in first or 2nd, bad in 3rd at high power settings, now almost constant in 5th, to the point that truck will not accelerate below 3000rpm in 5th even on flat ground.)
- Fuel flows above 4GPH/ OBDII "LOD" (engine load) reported above 75% are typical during malfunction. (Fuel flows have been as high as 9GPH with no problems on other days.)
Symptoms started at approx 292k and have been slowly getting worse over the past few months. . . . usually worse at beginning of trip, fading to very occasional after 50 miles of high-speed driving. Some days/trips no noticeable malfunction.
Thoughts:
1) Ignition wires tired? (did visual inspection, no obvious damage, but no water spray test performed, but seems likely given that the problem is most evident in conditions that would lead to high cylinder pressures.)
2) Fuel pressure? (not measured yet. . . original pump but possibility discounted due to intermittent nature of malfunction.)
3) O2 sensors tired/rat damage? (Original units still installed/ no obvious damage on cursory visual inspection under truck)
4) Injector going bad or injector wiring rat damage?
5) Plugged catalytic converters? (no sound of blown exhaust gaskets, exhaust flows well at tailpipe, with puffs at misfire.)
6) Cam sensor? (never been replaced; known issue with this model engine. Had intermittent mystery squeak that came and went at approx 250k-260k)
7) Clutch slipping? (never had one do that; always lose the throw-out first)
8) LSD problem? (fluid level/ appearance ok, last changed 150k; would expect worse in LOW gears)
9) Blown head gasket/s?
10) Cracked heads/ block? (Oil and coolant levels and appearance normal)
So: That's the plan of attack. What am I missing? (Clutch last done approx 170k; burned throw-out, did disk, flywheel, pressure plate, slave cylinder while the trans was down. I did not open the hydraulics or disturb the pedal linkage when I replaced the safety switch. )
I've been driving 93 ranger 3.0 4wd since last fall. first week I went to start and fuel pump relay had blown. I put a new one in and been driving since fine, till today. Now when I try to start, if it starts it will run fine all day as long as you don't turn it off. If you turn it off and restart half the times it will pop relay again. My fuel gauge has been stuck on full since I bought it also. I'm wondering if maybe pump has got had to start and drawing too much current...
View 3 RepliesMy sons 1998 ranger is in mph. Converting on to a kmh dash. There's one at the wreckers and I was wondering is it a direct replacement or is it a computer swap also? What years would work?
View 5 RepliesI am currently working on a 97 ranger with a 4cyl and 5 speed. its having some idle issues that i cant seem to pin point, you can start it and it will idle rough then when you rev it up it chugs real hard then dies. used my scan tool and all the sensors are good, fuel pressure is good, good compression, all 8 plugs are firing good and no codes. The other deal that has me a little confused is when I unhook the hose that runs from the air intake tube to the valve cover, I get a lot of vacuum at that port on the valve cover that the hose hooks to. Also when I plug it and pull the dipstick, I get vacuum at the dipstick tube. never seen this before but at the same time I've only messed with very few of these trucks so I don't know whats normal.
View 6 RepliesI have a 2001 Ranger 4.0L 4x4 with 101,000 miles on it. I went to go get in it the other day and the Air Bag Light came on out of the blue. I've drove it some since and it is still on. The light blinks for about 1 minute upon startup and then stays on solid for the remainder of the trip. What would make this come on so suddenly and is there anything I can do/check?
View 3 RepliesI have a 1998 ford ranger and it will not disengage out of 3 gear. The truck still starts but if you let of the cutch. Of course, It stalls. I'm doing the work myself but where I should start looking.
View 1 RepliesI have a 98 4x4 with 145k miles and 4.0 OHV. Symptoms are as follows;
Uses ALOT of oil. 1 quart per 230 miles. Burning bad in rear cylinders, some in middle cylinders, none in front cylinders. Screams intake or PCV issues to me, not rings or valves. Never any smoke, not even on startup. No significant leaks. MPG always 18-20mpg.
Slightly rough idle.
Miss under load below 2k rpm. Not a terrible miss, but you can feel it. Has never lit the CEL. I know the CEL is good.
Never loses coolant. No coolant in oil or vice versa. Haven't done compression test, but doesn't seem like they ever tell you much anyway.
This weekend I replaced all intake gaskets, plug wires, cleaned oil residue off and regapped plugs (they are 3 months old), injector orings, and PCV valve. Flushed and burped radiator.
It's too soon to tell on the oil consumption, but I thought the intake gaskets would have cured the rough idle and misfire. The idle IS much better, but still not perfect. But the low rpm load miss is actually worse now. Still no CEL. Could it be storing codes without lighting the CEL? Also, how do you clear codes on these, can you just disconnect battery, or do you have to clear them with a scanner?
I have been having with my ford ranger. I bought this off my nephew bcuz he needed some money and never drove it due to it being a 5speed and he has a kid and a wife and no room. OK the issue I am having is in gear or neutral I can't get the 2.5 motor over 3000rpms in any gear at all. If you rev the engine up or r driving it when it hits between 2900-3000 rpms the motor acts as if it is going to die and looses all power until you let off the gas. I have replaced the following items on the truck. Oh by the way I have a Cam 2 hand held and there are no codes or warning lights. All new parts :
1) new fuel pump
2) fuel filter
3)new timing belt
4)new motor craft platinum plugs
5) new motor craft plug wires
6)new Mass air flow meter
7) clutch,pressure plate & throw out bearing along with new slave(that needed it replaced others since I was there)
8) exhaust tube behind motor(rotted out)
9) new idle control sensor (acts as elect. Choke)
Truck starts up real quick and idles fine, but when truck is cold the rpms @ 2500 does the same as when it is warm @ 3000 rpms. I even took it to the local ford dealer in my town. Youngstown oh @ Fred martin ford. They told me the wires should be replaced and plugs along with mass air flow valve. I called them after replacing it and told them no difference and the service manager told me to bring it in again and they will look again. Service manager told me he has never heard of this type of problem and I went to a local garage mentioned it to the lead mechanic. He said that is why he doesn't like fords they are to common in chronic problems and can't be fix without a lot of guess work. I have a Hanes manual and did everything it recommends to no avail.
I've got 30 lbs of fuel pressure that drops to 28 if you rev it up a bit on a 1998 ranger 4.0 with a new fuel filter. Haynes manual say it should be 56-72 lbs. Bad news is fuel pressure regulator is in the tanks with the pump. Can the regulator be swapped out or is it one assembly with the fuel pump? Is there anything I should check first?
View 4 RepliesOk so my dad has been using my 98 while I was fixing his 92 4.0. I had the 92 perfect and then someone pulled in front of me and totaled it out. Well now I got my 98 back and it's all messed up. Check engine is on p0171. Fuel pressure test done and it's steady 40-42 psi. I remember last year I checked it was like 68-72 psi. It hasn't been a year or two since fuel pump and strainer were replaced. Filter probably 15,000 miles ago. It's currently running good sometimes it cuts off when you start it then next time it stays running. Is this another fuel pump failure? How much longer will it last on 40 psi? The fuel lines and tank have 336,000 miles, engine maybe 150,000 and injectors have about 20,000 miles on them.
View 4 Replies