Ford Ranger / B-Series :: 1998 - Charge Light Stayed On - Alternator?
Mar 7, 2012
98 Ranger 4.0..4WD ex CabXLT Automatic..started the engine yesterday and my charge light came on and stayed on. Checked the guage and it showed no charging and then slowly began to charge and the light went out. If I rev the engine above 2,000RPM's the charge needle starts to drop but if I keep RPM's below 2,000 charging is okay. Is this the sign of a failing alternator? The belt only has about 20,000 miles on it and tension seems oksy
View 4 Replies
Advertisement
So my truck drove great to ocean city MD this weekend. Power is perfect again, feels really tight. But now I have having to additional problems.
1) My alt light had been flickering a couples times a month. Last night it came on and stayed on. Lots of threads about this I Know!
I am hoping that cleaning and tightening the connections will do the trick since the alt is a Bosch with only 25k miles or so. But I want to order a rebuild kit:
is my alt a 3G or a 3G8429?
F SERIES | Alternator Starter Rebuild Kits
2) I started to have a ticking at idle. Its very regular and sounds like its coming from the passenger side valve cover. In random threads I have read about timing chain guides breaking and loose rocker arms.
Most of the time its 3 ticks in a row and then a pause. Should I be pulling the valve cover? Think I need to R&R the timing chain? I will post a video later!
View 10 Replies
I am having a problem with my O/D light flashing and my truck shifting hard. Just started out of the blue. After reading a few other topics, I am hoping it is the VSS. Now if only I could find the dang thing. Looking for a diagram, or detailed description on where it's at?
View 14 Replies
I just bought a 1998 ford ranger with 228000 miles on it seems to run fine has the 2.5 4 cylinder with auto trans. Check engine light is on and code is a PO171. I've cleaned the mass air flow sensor and fixing to install new fuel filter. what the problem could be?
View 12 Replies
My 2006 F250 has a single alternator and recently the charge light is on intermittently and I have watched output voltage fluctuate between 12.4 to 13.5 ... sometime a .3 volt bounce one way or another for no noticeable reason.
So rather than buy a new alternator, I would like to replace the voltage regulator and put in some new brushes.
What are part numbers that I need to pick up?
View 6 Replies
I noticed the passenger side on/off switch for the airbag doesn't illuminate anymore on my 98 Ranger. Whether I turn the key on the switch to on or off it doesn't illuminate either way. The airbag light on the dash flashes showing, counting a code 27 and then it stays on. I also noticed the seat belts on symbol doesn't illuminate and in the owner's manual it says it should illuminate and chime. I remember it use to illuminate but I don't remember a chime.
Someone with a 98 that has a seat belt reminder light that illuminates and chimes until you fasten the seat belt? I don't know if that and the airbag code is related. But I want to fix both? I guess the simplest one to tackle first would be the seat belt light/chime. I don't see a fuse for it. I guess I need to know first is it really suppose to chime.
View 12 Replies
Is there a fusible link from the alternator to the battery? The new alternator that I put on and got tested is not charging the battery. Was wondering if it could be a fusible link but I couldn't find it. Where it is located on a 2000 ranger?
Also, I put a DC volt meter on the negative side of the battery and the positive side of the CHARGING wire that would be connected to the alternator and got the same reading as if I put the meter on the positive of the battery.
Does this mean the fusible link is good?
View 14 Replies
2001 ranger with 4.0, alternator failed and new alternator is also not charging, showing very little output. i've installed 2 new ones with no fix. the regulator is in the alternator, correct? I'm stumped and not sure where to go with this.
View 14 Replies
1998 Ranger... I started having Speedometer/odometer problems after a power surge when my alternator went out. I knew the alternator was going bad and I tried to limp home another 5 miles rather than pay a tow bill and the alternator overcharged for a few seconds before completely dying. Since that time the only problem I am left with is my Speedometer and odometer have not worked. Scan tool says p0500 and I have replaced the ABS sensor on the differential with an OEM part but still no speedo or odo. I have checked all the fuses and relays associated multiple times. I do suspect that the RABS resistor is bad but there is no ABS light and it doesn't make sense that this one resisitor is the sle key for the whole speed control circuit. It's a manual transmission and RABS only. I swapped out the Cruise Control Servo with no luck as well. I am running out of options before having to take it to a dealer because I have to pass inspection. I have also checked and there is no power coming to 679 (GY/BK) into the instrument panel. I have also checked continuity for the rear harness to the ABS sensor and it is good.
View 2 Replies
I bought a 94 2.3 did a head job bought a rebuilt head and got it all back together hooked up the battery and blew the fusible link to the alternator. Did I screw something up? I have been rebuilding engines for a long time and never had this happen. Tested the alternator and the O'Reilly guy said that the Voltage regulator was shot putting out 17 amps and that is why the fusable link blew. I don't think that's right because the engine was not running I just hooked up the battery, and no I did not switch the pos and neg. I'm dumb but not that dumb. Any guesses?
View 1 Replies
We recently had a flash flood. No big deal, I was meaning to buy a shot vac anyways.
Anyways, the day after I started using my car, and noticed that my seat belt warning light stayed on, even when I was wearing it. Same went for the "Airbag" light. A couple of days later, the seat belt light start doing what it was supposed to; it would go off once the belt was "clicked". The airbag light has been on for some time. I figured I'd stop in to autozone and see if they couldn't check a code for me, but the nice gal behind the counter said they can only scan CHECK Engine/Service Engine lights. The airbag light, literally just the word "airbag" illuminated in red has been on for about two weeks now.
I imagine the flash food was nice enough to leave me with a shorted wire somewhere, but how to troubleshoot it.
View 5 Replies
My sons 1998 ranger is in mph. Converting on to a kmh dash. There's one at the wreckers and I was wondering is it a direct replacement or is it a computer swap also? What years would work?
View 5 Replies
I have a 2006 Ford F250 Superduty 4x4 6.0L Diesel with an alternator/battery problem. We have charged the batteries (had them tested at auto zone), and replaced the alternator and still cannot get the batteries to keep a charge. I'm not talking a slow drain, with the ignition switch on for less than a minute it drains about 4 amps and the truck dies. We also noticed a trouble code "TBC fault" and discovered that was to do with the trailer brakes. Disconnected the trailer brake system (have been noticing a "check trailer" warning occasionally recently). What could be causing such a massive drain on the batteries?
View 3 Replies
I have a 1998 ford ranger and it will not disengage out of 3 gear. The truck still starts but if you let of the cutch. Of course, It stalls. I'm doing the work myself but where I should start looking.
View 1 Replies
I have a 98 4x4 with 145k miles and 4.0 OHV. Symptoms are as follows;
Uses ALOT of oil. 1 quart per 230 miles. Burning bad in rear cylinders, some in middle cylinders, none in front cylinders. Screams intake or PCV issues to me, not rings or valves. Never any smoke, not even on startup. No significant leaks. MPG always 18-20mpg.
Slightly rough idle.
Miss under load below 2k rpm. Not a terrible miss, but you can feel it. Has never lit the CEL. I know the CEL is good.
Never loses coolant. No coolant in oil or vice versa. Haven't done compression test, but doesn't seem like they ever tell you much anyway.
This weekend I replaced all intake gaskets, plug wires, cleaned oil residue off and regapped plugs (they are 3 months old), injector orings, and PCV valve. Flushed and burped radiator.
It's too soon to tell on the oil consumption, but I thought the intake gaskets would have cured the rough idle and misfire. The idle IS much better, but still not perfect. But the low rpm load miss is actually worse now. Still no CEL. Could it be storing codes without lighting the CEL? Also, how do you clear codes on these, can you just disconnect battery, or do you have to clear them with a scanner?
View 14 Replies
I have been having with my ford ranger. I bought this off my nephew bcuz he needed some money and never drove it due to it being a 5speed and he has a kid and a wife and no room. OK the issue I am having is in gear or neutral I can't get the 2.5 motor over 3000rpms in any gear at all. If you rev the engine up or r driving it when it hits between 2900-3000 rpms the motor acts as if it is going to die and looses all power until you let off the gas. I have replaced the following items on the truck. Oh by the way I have a Cam 2 hand held and there are no codes or warning lights. All new parts :
1) new fuel pump
2) fuel filter
3)new timing belt
4)new motor craft platinum plugs
5) new motor craft plug wires
6)new Mass air flow meter
7) clutch,pressure plate & throw out bearing along with new slave(that needed it replaced others since I was there)
8) exhaust tube behind motor(rotted out)
9) new idle control sensor (acts as elect. Choke)
Truck starts up real quick and idles fine, but when truck is cold the rpms @ 2500 does the same as when it is warm @ 3000 rpms. I even took it to the local ford dealer in my town. Youngstown oh @ Fred martin ford. They told me the wires should be replaced and plugs along with mass air flow valve. I called them after replacing it and told them no difference and the service manager told me to bring it in again and they will look again. Service manager told me he has never heard of this type of problem and I went to a local garage mentioned it to the lead mechanic. He said that is why he doesn't like fords they are to common in chronic problems and can't be fix without a lot of guess work. I have a Hanes manual and did everything it recommends to no avail.
View 14 Replies
I've got 30 lbs of fuel pressure that drops to 28 if you rev it up a bit on a 1998 ranger 4.0 with a new fuel filter. Haynes manual say it should be 56-72 lbs. Bad news is fuel pressure regulator is in the tanks with the pump. Can the regulator be swapped out or is it one assembly with the fuel pump? Is there anything I should check first?
View 4 Replies
Ok so my dad has been using my 98 while I was fixing his 92 4.0. I had the 92 perfect and then someone pulled in front of me and totaled it out. Well now I got my 98 back and it's all messed up. Check engine is on p0171. Fuel pressure test done and it's steady 40-42 psi. I remember last year I checked it was like 68-72 psi. It hasn't been a year or two since fuel pump and strainer were replaced. Filter probably 15,000 miles ago. It's currently running good sometimes it cuts off when you start it then next time it stays running. Is this another fuel pump failure? How much longer will it last on 40 psi? The fuel lines and tank have 336,000 miles, engine maybe 150,000 and injectors have about 20,000 miles on them.
View 4 Replies
I got this 98 Ranger 2.5 that I've done a tune-up on less than 30,000 miles ago. I changed plugs, wires, and both coil packs. Timing belt, thermostat, fuel pump, fuel injectors are all recently changed too within a year or two. Fuel filter and air filter I change every 30,000 miles. The truck runs as great as a 4 Cylinder will run. It's at 344,000 miles but the engine was changed once so it probably has over 100,000 miles on it. There is just a slight miss you can hear through the tailpipe but it's not severe enough to be picked up by the Check Engine Light. In fact, even when the coils were totally gone it never put up the Check Engine Light. I can tell when a coil pack is going out on this because it's done it several times so I usually just change them with the tune-up. It's only a slight miss some people may not even notice it. I was just wondering is there any way to track down where the miss is? I tried looking under the hood in the pitch black and there's no plug arcing.
View 1 Replies
so heres whats happening. My 98 ranger speedometer has not been working since I owned it (I am the second owner who got it from a grandpa) and I've replaced the vss sensor two times, got a new connector and gave that a try and still nothing. Yes I've looked for cracks in the wire or any exposed copper, I've looked through many forums and cant figure it out. At first before replacing the vss, my abs and check engine light weren't lit up until i put a new vss sensor on that i got from o'reillys, so then i got another one thinking it was just a bad sensor and still no luck. another thing is when its cold in the morning and i get in my pickup to go to work it will start working once i go over 30 and fluctuate between that and 20 but if i don't accelerate it will not bounce all over the place.
View 4 Replies
I have a 98 Ranger SuperCab XLT 4WD 4.0 Auto. Occasionally, especially when it has been sitting for more than 3 days, it shakes for maybe 30 seconds on startup. It smooths out gradually after that, maybe 15 sec. to normal smoothness. It seems like it is firing on all cylinders and is more like something out of balance.
Never does it when sits less than 2 days. When it happens, the longer it sits the worse it shakes.
View 3 Replies
