I have a 1998 ranger 4.0 and about a year after getting it the belt started to squeak so far if have replaced the belt, replaced the tensioner, and cleaned and wire brushed all the pulleys to remove glazing. And it still squeaks and its annoying and kinda embarrassing...
View 4 RepliesIn a few weeks I will be bringing my new to me Ranger back to the great state of Texas. The truck however, has a squeak when running, which I think has been concluded as the idler pulley for the timing belt. Well, I'm nowhere near the truck still and in order for it to get here it will need to be driven half a day to reach me, at which point I could do all the work it needs done.
My question is: Should I take the risk and have it driven here before the belt change (I did look at it while I was out there and it's already cracking pretty good), or should I go ahead and have someone get the belt done at a shop? It's less the belt that concerns me I think, and more the pulley, even though it's just started squeaking in the last 1000 mile.
So i have a 1998 4.0 ohv ranger and have been fighting belt squeak shortly after i got it. I've replaced the belt twice and the tensioner twice when i put a GATES belt on it stopped for like month. But its still squeaking. If i put a wrench on the tensioner and turn it the squeak stops. So i need to find a way to tighten the tensioner could i somehow jam it, our hook up a turn buckle bolt to manually tighten it, or use a different ford tensioner. I really need to do something cause this squeak is just down right annoying.
View 2 RepliesI noticed the passenger side on/off switch for the airbag doesn't illuminate anymore on my 98 Ranger. Whether I turn the key on the switch to on or off it doesn't illuminate either way. The airbag light on the dash flashes showing, counting a code 27 and then it stays on. I also noticed the seat belts on symbol doesn't illuminate and in the owner's manual it says it should illuminate and chime. I remember it use to illuminate but I don't remember a chime.
Someone with a 98 that has a seat belt reminder light that illuminates and chimes until you fasten the seat belt? I don't know if that and the airbag code is related. But I want to fix both? I guess the simplest one to tackle first would be the seat belt light/chime. I don't see a fuse for it. I guess I need to know first is it really suppose to chime.
I have a 98 ranger with 2.5 and 225k mostly trouble free miles. This engine has never used a drop of oil and ran good. In Dec 3 miles from work started running poorly and sounded to knock the more I asked for power. The CEL started flashing I made it to work and it idled rough but more rpms smoothed out. Took it to mechanic says he did a compression check with little or no compression on #1 & #2. #3 & #4 fine must have broke rings. Doesn't seem right to lose 2 cylinders at the same time out of the blue. Could anything else be causing these symptoms or time for a heart transplant? He hasn't opened anything up yet.
View 6 RepliesMy '02 4x2 has developed this half scrape half squeak noise in drive. 140k, 55RE trans, all original drivetrain. It sounds like someone wrapped a wire coat hanger to the driveshaft. (No, I looked). It seems to be in sync with the speed of the shaft or wheels. U-joint maybe? If I have to take it to a garage I'd like to have some clue what to tell them to look for.
View 4 RepliesThere's a small but clearly audible chirping/squeak coming from my truck whenever I pull out. It goes away after the truck gets hot, but for the first 10 minutes or so, it squeaks only when moving. Not at idle. It is worse at low RPM's in 1st gear. And it's particularly bad in the mornings. I was thinking it is something in the idler pulley or the belt tensioner.
View 7 RepliesI've got an '08 FX4 that has developed quite a loud and annoying squeak from the rear leaf springs. It happens when I'm slowly applying power and going over bumps such as speed bumps or similar. More so when I'm going up hill.
I initially thought it was a u-joint going bad, and had my driveline mechanic take a look at it. He discovered it was the rear leafs making the noise. He sprayed them with an aerosol light grease and the noise was instantly gone. The problem is, the noise comes back after the grease spray has worn off (usually after driving in the rain) which happens a lot in the Vancouver area.
This is my 3rd Ranger and I have never had this problem. I don't drive in unusual places (beach, sandy, dusty areas) so I don't know why this is happening. It does look rusty in the areas that I can see in between the individual leafs. Is this a common problem for this vintage of Ranger?
I have a slight squeak noise that is only heard at idle some of the time. I replaced the belt, idler, and tensioner when I noticed just spinning the alternator gives the sound I'm hearing. Is it something I should be concerned about? It isn't noisy all the time, only sometimes. I don't want to fix what isn't broken, but I don't want it to leave me stranded one day either.
View 3 RepliesI've tried every variation of installing the timing belt on my '91 2.3L Ranger, still not in. The belt seems as if it's too short but I've been told that it "barely" fits, no kidding! I've pulled the crank balancer/timing trigger off and put it back on three or four times already. What's the trick? Everytime I get it close I'm off a tooth or more. Just frustrated, tired of hitching a ride to work.
View 14 RepliesI have a ranger as said in title. No a/c. I noticed my belt was cracked very badly so I bought a new one. Dayco made for Ford and Mazda 3.0L V6. Looked the same length as the old one so I put it on and all was good. Then about 2 days later it started squeaking very loudly, not all the time, just 1500 rpm and higher. The hotter the motor got (not overheating just to running temp) the higher rpm it took for it to squeak. I put a stethoscope on all the pulleys/pumps and alt. It sounded the strongest on the idler.
So I replaced the idler and bearing (which the bearing was bad, but not the source of sound) it wasn't that. So I thought I'd give the belt a couple days, maybe it was too tight causing a bearing to get too tight and squeak. And the more I drove it the louder it got with less rpm needed to make it squeak. So I tried belt dressing, and still no fix. So today I put the old belt back on to see if that was the issue. Sure enough, it started up and squeaked just the same, but I tried the belt dressing on the old belt and it went silent, even at 3000 rpm. So I assume from this the new belt was a smidge too big. Right?
After about 1 minute after starting the truck it sounds like the fan belt is squealing..(below 30 deg outside) Only its not the fan belt as I replaced it. Does not do it when it is engine is operating temperature. Have checked all of the Pulleys which seem to be all right. The frequency of the squealing sound is about 1/3 the engine RPM and will go away above 2k when it does do it. Stopping at a stop light after about 45 seconds it really starts to get loud. Can a Fan Clutch do this.. I beleive that this engine has a timing chain right?
View 8 RepliesWhat is the recommended interval for the timing belt change? I have a '96 B2300 with ~85K on it and he original timing belt. I wanted to change the serpentine belt and my mechanic said he'll take a look at the timing belt. It's not cracked or anything but he says that after 8 years it should be changed.
View 14 RepliesA C-note for those 2 pieces of nothing seems ridiculous. Considering sanding and painting instead.
View 2 Replies2003 3.0 ranger... This will be my 3rd time replacing serpentine belt and if needed 2nd. time for idler, tension pulleys...NOT SURE WHAT TO DO, should i replace parts again?
View 5 RepliesI have a 2003 Ranger 2.3l with 327k miles on it. I recently replaced the belt and now it doesnt want to start. The belt is on correctly and tensioner is tight. The battery is fully charged its just not firing up and starting. All connections are good, the ac and power steering pulleys are relatively new. Now i have been stuck tryin to fix it for a week...
View 8 RepliesI recently bought a 2003 Ford Ranger. What I want to do is unhook the seat belt chime. In the past with the other 3 Rangers I owned I unplugged it from under the seat. But when I unplugged this one the light for the air bag stayed on. I like the freedom to choose and I don't care for the chime.
View 14 RepliesCouple days ago, hop in the truck to go to work and belt starts squealing. Belt was old and it had been raining, so I figured it was a little wet. Turned on the defrost, and squeal gets worse. I then smell a burning. Opened the hood and saw the belt dragging on the a/c pulley, so I figure the compressor clutch is shot.
Looked at it today. I was wrong. Took off the belt and the a/c pulley spins fine. I can turn it's front hub by hand as well. I look around and see the crankshaft pulley isn't lined up. It looks like the outer pulley portion separated from the rubber. This caused the belt the jump and ride on the rubber part, cutting grooves in it.
Here's some pics:
From top driver's side:
From top passenger's side:
From bottom passenger's side:
My sons 1998 ranger is in mph. Converting on to a kmh dash. There's one at the wreckers and I was wondering is it a direct replacement or is it a computer swap also? What years would work?
View 5 RepliesI have a 98 Ranger with a 3.0 (5 speed) that has 254,000 miles on it. I drove it to town this morning (8 miles) and it ran normally. I stopped for just a few minutes at a house and when I re-started the truck, it was missing very bad and the CEL came on. It wouldn't haul itself in anything higher than 3rd gear. I decided to try to make it back home. I drove it less than two miles and it cleared up and started running perfect again. I came home anyway and read the code with my scan tool.
It said that I had a miss fire on cylinder #5. I erased the codes and shut the CEL out and its been running perfectly ever since. (I have put about 150 miles on it so far) If it does it again, I will start by replacing the plug wires. I have already done that but its been a long time ago. The plugs have been replaced twice as well. I was wondering if it could be something other than electrical like a dirty injector or maybe the compression rings lined up and it momentarily lost compression.
I have a 1998 ford ranger and it will not disengage out of 3 gear. The truck still starts but if you let of the cutch. Of course, It stalls. I'm doing the work myself but where I should start looking.
View 1 Replies