Ford Ranger / B-Series :: 1998 - Battery Died Now Stalls?
Sep 23, 2013
98 Mazda B4000 4.0 4x4
I bought this truck about two months ago and it has been great no problems starts right up and runs like a top. I was installing a 4 channel amp yesterday on and off and the dome light was on all day as the doors would periodically be opened or closed so it never did that cycle of 10 min or whatever when the lights turns off. This is what killed the battery.
I had my neighbor jump me and after a few minutes of charging it started right up and idled for about a minute long enough he left and parked, then it stalled. I started it about another 6 times before the battery died again. Every time it started fine then would idle between 1-10 sec then start to sputter and eventually die. Pressing the accelerator pedal only killed it faster.
I got a new battery today as the other charges so that I could fix it today without missing work again tomorrow. Unfortunately it does the same thing I was hoping that the voltage was just low or the polarity flipped or something on the other battery.
To sum it up the truck never gave previous symptoms just simply ran too low (battery never DIED the lights came on just clicked when starting) on power and now stalls when started which it does immediately no long cranking.
The twist; truck has an aftermarket alarm by Python. Problem is I don't know anything about the alarm or if it comes with an immobilizer. I am in the process of trying to figure this out but need to pull dash or something to find the "brain"? Never had an alarm like this I disconnected the clear square that adjusts the sensitivity hoping that was it but I don't know where or what I assume the brain of the alarm is.
View 14 Replies
Advertisement
My friend's 1997 4 cyl ranger died and won't start. Cranks fine with no codes on OBD2. Was running fine before it died.
View 5 Replies
My Ranger has been acting funny lately. My check engine light is on. I stopped by an Autozone and the guy read the codes - I don't remember exactly what the code was but he said I just needed to use some fuel cleaner - he recommended Seafoam. Now, I assume he was just trying to sell me something. But I've tried that, Gumout and STP in the tank with no luck.
If I'm driving and come to a stop, my RPM dips down to about 600 or lower, my truck starts shaking and will eventually stall if I don't step on the gas. This only happens with a warm engine - If I start the car up and go a mile down the road, it won't happens. But if I go 10 miles down the road, it will. I assumed I had a bad throttle position sensor so I just ordered the part and replaced it but the same behavior exists.
It's been a while since I've replaced the fuel filter - it might just be that.
View 11 Replies
My 2001 2.5 manual suddenly died. The starter turns the engine over, but I don't get a) fuel (changed the fuel pump) b) spark c) Engine check light. When I plug the OBDII reader in, it simply says "ERROR". No codes, no other language.
While trying to figure it out this morning, after trying to start it 50 times, it actually fired for a few seconds, but then died again.
I checked relays and fuses and nothing seemed bad. I swapped relays around too.
I unplugged the battery, then the computer, but nothing got it to fire again.
View 4 Replies
My Father in Law's 95 Ranger, 4 Cylinder, 5 Speed has started acting strange. It has, in the past 3 weeks just died suddenly, and won't restart. No action at all when you turn the key, as if the battery is disconnected. Wait for 45 minutes to an hour, and it starts back up again.
He has had it to a local shop twice, and the only thing they have done is let it idle for 5 hours at the shop. Of course, it never stopped.
Now they are saying it is the clutch, and depending on the type of clutch, (big or small).
I've been working on cars most of my life, and even had an 87 Ranger, and I've gotta call BS on this. He says it happens mostly when coming to a stop.
View 4 Replies
So my 99 2.5 rcsb has been stalling out under loads, particularly when the A/C is on. It's stalled when warm, cold, engaging Drive or Reverse, and it steering does it at least once a day. There's a missing elbow to a vacuum line at the driver side (looks RABS related). The truck had the CAT melt off and now it's laying in my bed with the O2 sensor, don't know if that relates.
This truck sees 100 miles a day through the mountains, 5-7 days a week. It only has 140,000 miles on it, I put 40,000 on it in the last year with no issues. The truck is very much showing age (needs almost everything), but I'd like to keep the basics going.
View 14 Replies
1994 FORD RANGER stalls while driving - differant speeds ...differant miles ...no rhyme or reason to it - cranks right back up ...can even pop clutch and cut it back on. Already replaced Ignition Start Module - Dpes sensor - temp sensor - and scan shows all codes are clear and truck passes. We are clueless to whats causing this. 4 cyl 2.1
View 12 Replies
so I have a 1987 2.9L Ranger that likes to stall out when its idling after reaching temperature. Ive replaced all sorts of sensors (IAC, Coolant Temp, and PCV) and so far no luck. I was trying to figure out what the relearn procedure was for the IAC or get an input on any other possible sources of error. I haven't changed TPS yet.
What the engine does is when it gets up to temp, the engine will start to loose speed, and will start to shutter. Then it'll kick back up run fine for a few seconds and drop again, it'll do this for a few minutes then completely just choke out.
View 3 Replies
2003. Ranger xlt with the 4.0.... So I just bought this truck and was informed that the vacuum might not be functioning correctly. And here's the symptoms. It idles a little rough, nothing major. When I put the truck into gear either drive or reverse, it stalls out almost every time unless I give it some gas and hold the brake. But after that I could drive it all day with out a problem, as long as I don't put it into park. And last it starts a little hard. But the damn thing runs great while driving it. It's still very snappy even having high miles.
View 4 Replies
So a couple days ago I started my truck and it fired up like normal, but then sputtered out and died after a few seconds. I tried starting it up again and it did the same thing. I tried once more and it started up fine and I drove away.
It sounds like my truck is running out of breath or something and just sputtering out. Runs fine once it turns over though. My issue is that it is happening almost every time I start it now. I have to turn it a couple times before it catches. What this might be?
View 11 Replies
I was driving my 85 2.3 liter down the road and it died all of a sudden like and wont start back up. I took out a plug to check for spark and had someone turn it over and I touched it to the big metal part the grill connects to at the top but I got nothing. It IS getting gas. The spark plug was white as if it was really hot and rough-looking for its relative newness. I bought a new distributor cap because it was corroded, but it didnt work. They tested the ignition module at the store and its good, so I am thinking distributor?? Also, could compression issues keep it from sparking? I am a little worried it got over-heated somehow, but don't know....
View 9 Replies
My 2003 ranger, 4.0l, 5 spd manual with 295K miles has no power on acceleration. Engine shutters/stalls. The following have been replaced in last 20k miles; fuel pump, plugs/wires, mass flow sensor and fuel filter. Last week left for work and could not go faster than 50 mph. Condition has gotten worse (barely goes past 40 mph).
Changed filter with no improvement.
Checked fuel pressure - constant at 65 psi.
Changed coil - no change.
The tank of gas I put in just before problem was from station with tanker dumping while I pumped. That tank is out of truck; filled from different station. Also put can of seafoam in tank. No change.
View 1 Replies
I'm having a bit of trouble with my fathers '03 Ranger Edge 4.0L. It has about 100k miles on it, and we keep it very well maintained. This is the first major problem we've had with it.
When the problem first occured, it had been driven about 30 miles on the highway and about 5 miles after getting off the highway, he pulled up to an intersection and stopped. As he started accelerating again, it all of a sudden started sputtering, surging (almost exactly as if it were running out of gas), and then stalled. It continues to exhibit this behavior. It will start and idle fine, but struggle and then stall when given any amount of throttle. It's also an automatic transmission if that makes any difference.
Fast forward to this past week after we had it towed home. We have checked the fuel pressure, and its dead on at about 64psi. We changed the fuel filter, changed the PCV valve, changed the upstream O2 sensor, put in a new air filter, cleaned the MAF sensor, and cleaned the intake of the throttle body. We're now at a loss as to what could be causing the problem. The CEL is not on, and there are no codes being shown when we plugged it in. We also thought it may have been bad gas, so we drained the tank and put fresh gas in from our preferred station. The plugs and wires are also fairly new, only about 4k miles on them.
Are we missing anything here? What else we could try? The absolute last resort is taking it to a shop, we're going through a rough patch with finances.
View 3 Replies
I have had my '99 Ranger since 2002. Since it has started getting hot in Texas, the truck has decided to stall at horrible times. When driving on the interstate, there is no problem, but as soon as I get in town and have to let off the gas to turn or stop, the whole truck dies. Unless it sits for a long time, it will continue to die at every stop. It is harder to start each time. I have changed the fuel filter and added STP to the last tank of gas. Also, it is tough to start and keep running until it has warmed up on any day. I have to sit in the truck and keep the idle up so it won't die.
View 1 Replies
I have a 86 Ranger with the 2.3L fuel injected 4 cylinder and a 5 speed manual transmission. I can drive it for hours on the highway but if I get caught in stop and go traffic, it stalls and won't restart for about 10 minutes. When trying to restart it acts as if it is fuel starved. Spraying carb cleaner in the throttle body does make it run for a second or two. I was getting a code 18 & 67 before I changed the ignition module, now I just get code 67 or 11. I have done the following:
-Changed both fuel pumps, tank and frame rail pump (did one at a time, no improvement)
-Changed all fuel filters (in line filter, fuel reservoir filter and tank filter)
-Changed ignition module on distributer
-Changed both relays that control fuel pumps
-Cleaned battery terminals and body ground connections.
-New gas tank fill cap
I'm at a loss now as to what to do. I have been checking the codes with my multi-meter. I do not have a OBD1 diagnostic tool.
View 8 Replies
The truck started acting up while driving. It would shut off (no miss or anything), but would start again. Now it is sitting in the driveway and wont run more than 3 seconds. The fuel pump has been changed and did not work. The fuel pump relay is new and did not work. I read that the fuel pump goes to another circuit after start up. Could it be running to start and then shutting off? Inertia switch is not tripped. Where to look next. 1992 Ranger 6 cylinder ....
View 10 Replies
Well it all started when I was having starter issues my starter died and my solenoid was just clicking and after time there was no power at all to anything in the truck i have replaced the solenoid and starter and check battery and cleaned post and terminals. I am going to replace my negative cable as it was pretty bad but if this still does not work, so what to look for. The truck is an 87 ford ranger 4x4 5 speed with a 2.9....
View 9 Replies
I am working on a 96 Mazda b2300 auto 2wd for a friend. His son was driving it when a loud noise, it died and wouldn't start back up. He had it towed to my house, I started to tear into to it and found it slipped the timing belt. So a rebuilt head, gaskets, timing belt, fuel injectors, water pump, thermostat, plugs, and fluids; tried to start it and nothing. Started troubleshooting and found the primary coil pack was out of spec, replaced and still nothing.
Changed out the CKPS still nothing? I have spark, I have fuel, I'm going to check compression tomorrow but the way the cylinders and pistons looked I don't think that is the issue but I going to check anyway, rechecked the timing marks they all lined up. Checked the fuel inertia switch not tripped. Could the PCM, or ICM cause a no start, and still be able to get spark and fuel?
View 2 Replies
My truck has been doing this since I got it and I can't figure it out. It's a 2000 Ford Ranger XLT 2.5 5Spd. It runs fine if you don't rev it above 2500-3000 rpm. After you rev it that high coming down to idle it is stumbling real bad and sometimes stalls. I've been driving it like this since I got it, and it does fine other than this. It gets better the longer you drive it, but it still will do it if you rev it high enough.
Here are all the parts I personally have changed (previous owner said he did the plugs and wires and air filter, which it looks like he did but I'm about ready to change them myself):
-Fuel filter
-coil packs
-timing belt
-egr valve
-cleaned throttle body
-iacv
-tps
-thermostat
View 14 Replies
My 2005 2.3l Ranger ran great. I moved a trailer about 150 feet and stalled the truck backing it up. Stick shift. Unhooked the trailer and pulled back into the parking area....all the sudden the truck has extremely rough idle and stalls. It runs good on the highway. AutoZone ran a OEM number to cross: P0171.
I cleaned the IAC with intake cleaner. No Luck
I unhooked battery for 15 min. No Luck
I sprayed intake with 1/2 can of intake cleaner. No Luck
I did not have a tamper torx to remove the MAF. What next.
View 14 Replies
I've recently acquired a 1989 ford ranger xlt 2.9L V6 and iv got my elbows deep already..... starts right up and scene its an older truck i let it warm up for a few minutes seems to sound alright so i jump in and take off... well i make it about two blocks and as soon as the truck seems to warm up it starts to sputter and die out... starts back up and idles for a min and i try to take off, but it seems to have NO power and jerks and dies.... so i push to a street parking spot and get situalated start the truck up again and take off only to make it about half a block tell it does the same....
First i think iv run outta gas witch i might of not sure so I walk to station and get three gallons. put in truck and same is happening. so i start kicking myself for not haven any tools with me and i leave tell next day... that night do a little research and get some idea's of what could be the problem'(s) so i start out with things that look like they need tending Badly WIRES, PLUGS, ROTOR, CAP, MAP SENSOR, and now after a whole day in the rain (Northwest BTW) and grease to elbows? 2.9 V6? What step's should i take next?
View 10 Replies
