I have had my 1998 Mazda B2500 truck since 2000 and this problem comes and goes (it's mostly been gone lately). Usually when it is cold outside. At slow speeds it creaks and squeaks - kinda embarrassing - if I am sitting still it squeaks when I turn the steering wheel. Once the speed picks up you can't hear it. I have noticed this in other fords about the same year.
View 1 RepliesSo i have a 1998 4.0 ohv ranger and have been fighting belt squeak shortly after i got it. I've replaced the belt twice and the tensioner twice when i put a GATES belt on it stopped for like month. But its still squeaking. If i put a wrench on the tensioner and turn it the squeak stops. So i need to find a way to tighten the tensioner could i somehow jam it, our hook up a turn buckle bolt to manually tighten it, or use a different ford tensioner. I really need to do something cause this squeak is just down right annoying.
View 2 RepliesI have a 99 ranger with 170000 miles and the front end recently started squeaking. its coming from the driver side but I can't pinpoint it.
View 5 Replies4x4 1999 Ranger ... They are a squeaking and driving me crazy. How hard are they to do, do they need a press or can they be done at home?
View 7 RepliesMy '02 Ranger has had tire wear for a while now, and its on the inside of both front tires. I was thinking it was either toe or camber, or maybe both. I havent been able to get an alignment recently. If its the camber, should I get the camber kit from Ford?
As for the squeaking, it first happened last summer, and I sprayed WD-40 on the upper control arm bushing and it went away until last week (obvoiusly temporary). Now its back. Also happens while turning the front wheels.
I'm hearing a sort of faint rotating squeaking noise coming from the front of the engine; I can only assume that it's something with the belts. Nothing too pronounce cause I just notice it yesterday, anyway I was hoping I get another take on what this might be before I take it to the mechanic tomorrow.
View 12 RepliesI have a 98 ranger4x4 front hubs will not lock in. replaced vac lines that were rotten still will not lock,checked vacuum at solenoid had vac for a min or so then it stopped, ran vac strait to main vac line for continuous vac and they still will not lock in, had 4 wheel just the other day. What can I check or do besides set it on fire.
View 1 Replies98 Ranger Front brake lines Too short! they kink in sharp turns and wear out then start to seep then eventually leak and need replacement. Checked parts references and the lines have been considered stock. Not sure if I have a 1/2 year model.
View 1 RepliesOK here's a new one (for me anyway). My Reg started to produce a squeaking noise from the chassis. I can't tell exactly where its coming from (yet) but it seems to occur mostly at slow speeds. I can reproduce the noise by driving over a speed bump or making a slow speed turn. I suspect an exhaust hanger as it seems to happen front and rear. I cannot reproduce it by bouncing on the corners of car though.
View 3 RepliesI drive a 2002 4-dr 1.6 L Accent and there is a strange, high-pitched squeaking that comes about from somewhere under the car at very slow speeds (30 mph or below). If I hit the brakes, the noise continues sometimes as the car slows. (The noise isn't the brakes, though, I know that), but if I hit the gas pedal slowly, the noise stops. Whatever is vibrating underneath doesn't seem to be causing a problem at high speeds. Or I just can't hear it.
Secondly, I am going to try to do some tune-ups for the summer for lack of better things to do, mostly, I can pretty much do anything (intake/exhaust, engine, electrical) as long as I can find detailed instructions.
I have a 2002 Ranger 4.0 4x4 Off-road. Over the weekend I started hearing a squeaking sound that varied with the throttle, so I guessed the u-joints needed work. I took it in (no garage or tools available atm), and the garage called me later in the day saying my driveshaft was unrepairable, that I needed a new one. I told them to hold off.
Now, a little research found me some sites claiming that Ford did indeed make some disposable driveshafts, with pinned u-joints, but in the F-series, not the Ranger.
I have a ranger as said in title. No a/c. I noticed my belt was cracked very badly so I bought a new one. Dayco made for Ford and Mazda 3.0L V6. Looked the same length as the old one so I put it on and all was good. Then about 2 days later it started squeaking very loudly, not all the time, just 1500 rpm and higher. The hotter the motor got (not overheating just to running temp) the higher rpm it took for it to squeak. I put a stethoscope on all the pulleys/pumps and alt. It sounded the strongest on the idler.
So I replaced the idler and bearing (which the bearing was bad, but not the source of sound) it wasn't that. So I thought I'd give the belt a couple days, maybe it was too tight causing a bearing to get too tight and squeak. And the more I drove it the louder it got with less rpm needed to make it squeak. So I tried belt dressing, and still no fix. So today I put the old belt back on to see if that was the issue. Sure enough, it started up and squeaked just the same, but I tried the belt dressing on the old belt and it went silent, even at 3000 rpm. So I assume from this the new belt was a smidge too big. Right?
I have a 1998 F-150 and I have a squeaking noise and I can only hear it when I am in in first gear at low speed and when I'm in reverse backing up and goes away when I press the clutch pedal. I'm thinking its either my U-Joints or Throwout bearing.
View 3 RepliesMy o/d has started shifting in and out at speeds over 50mph. It looks like it happens for the tiniest changes in engine loading. A windy day plays havoc and mild inclines. Sometimes the o/d light starts blinking until I switch off then operates normally. Extended warm-up driving seems to work. I've been told the rear axle speed sensor may be going bad but I have no confidence in the advice. I am driving an '02 ranger, 3L flex fuel, 2wd and just went over 100k. The atf is at the correct level but the fluid needs changing in my opinion. There are no engine codes.
View 5 RepliesI have a 1999 ranger 4x4 , when I'm going to a slow final stop the abs kicks in ,doesn't do it every time , there's no abs warning light , took it to the ford dealer they scanned it and said it was the left front hub & bearing assembly, said the sensor wasn't reading the back of the bearing assembly. I can't understand way the abs light isn't on, is there anyway to clean that they want to replace the hub & bearing, Is a use hub & bearing replacement a good way to go? They told me I could pull the fuse and kill the abs, but I find three fuses I pull aII three and got a speed sensor check engine code. I hate to replace that hub & bearing when there's no problem with the bearing ,Is there any way to deactivate the abs, by the way it's 4 wheel abs.
1999 FORD RANGER 4X4 4.0......
My overflow tank seems to be going empty slowly. The last time I filled it was in March and I filled it to the Full line. Now, the overflow is almost empty. I did 425 KM last night almost non-stop and the level stayed the same since that night and today. So, I am not burning any thru the gaskets. Exhaust is not white neither.
I did see one suspect thought. I have this really small rad at the bottom of the bumper and it seems a little wet around the tubes that enter it. Could it be that? I have no spots on the driveway or road when I park. Specs of my truck:
190 000 KM.
Oil changed on Saturday.
Runs well, no loss of power.
Temps are good.
Whenever I slow down for a car to turn or accelerate after a stop sign the ice cold air goes away and is replaced by warmer air but then it never turns back cold. Only when I kill the engine and start back up does it return. I just had the Freon refilled and there are no leaks.
View 3 Repliesi have a 02 ranger 4by4 with 4.0.every time i try to fuel the pu it spits gas back out the fill tube and i have to fill it very slow to get fuel in it.i just replaced the filler neck about 6 mos ago due to having a hole in the the hose by the local ford dealer,
View 6 RepliesI noticed that my ABS was engaging when I would slow down to a stop while turning left. I pulled the fuse for the ABS just to make sure that's what was causing the pulsating brake, and it was. Anyway, if it's an ABS sensor problem, would it be the front passenger side sensor if it's only happening when I turn left? Is there a way to test this. Would a scanner detect it? It hasn't been throwing a code or anything. Just the ABS engaging while braking and turning to the left when it shouldn't be.
View 6 RepliesI have a 97 ranger 4 cyl that's been making a whistle noise the last few weeks. The sound is literally like a whistle and the noise level varies but its never obnoxious or loud. The sound does not happen when truck is idle, seems to happen mostly when I first accelerate and slow down although sometimes it does happen when I am going 20-30. it doesn't happen all the time but lately its happening more. What this could be? The truck idles and runs great.
View 14 RepliesI have an 87 Ranger and the oil pressure gauge is slow to respond changes in pressure. Is this the way the gauge is designed to work or do I have a bad sending unit?
View 4 Replies