Ford Ranger / B-Series :: 1998 - A/C Compressor Run All The Time Whilst Driving?
Sep 28, 2016
This is a question in general about Fords. My 98 Ranger doesn't do it. He's got a 1987 Ford Mustang 5.0 with original factory a/c. He changed his compressor to a used one and it started running all the time whether the swtich was off or on. He said he switched back to his original compressor and it still does it. I figured it might be something common for Ford a/c systems so I figured I would ask. I'm not sure why it would be unless the mode switch was bad.
View 5 Replies
Advertisement
I opened up my hood yesterday to check on everything and happened to notice that my radiator cap was gone. I don't know if I just forgot to put it back on the last time I checked my coolant or what happened, but I of course immediately bought another one and put that on. What happened to the old one. Looked all through the engine and didn't see a cap laying in there anywhere.
Anyway, do I have anything to be worried about? My truck has never overheated or anything. I really don't know how long I was driving around with that cap off. The coolant was a little low in the radiator but actually not too bad. Only had to add a little to get it back to the top. Should I be worried that this caused any damage in any way or am I OK since I never overheated?
View 5 Replies
The Problem: When I start my Ranger it dies right away, I do this about 10 times or so (worse when it is wet or has rained) then I can finally keep it running, by hitting the gas. Once I get it running it will cut out while driving as well. The idle is normal and if fires properly, I just took it in to the shop (non-dealer) and they said it fires normal and has normal fuel pressure, and the their computer returned no error codes. Their sugestion was replace the throttle position sensor. Do you all think this part could be the cause and where is the this sensor and is it hard to replace?
View 12 Replies
What would cause my 4x4 high and 4x4 low lights to flash intermediately together on cold mornings while driving? It won't switch into 4x4 when it does this either. When it sits and warms up later in the morning all works as should. It doesn't do it all the time but when it does its annoying not to mention it's sucks when I need 4x4.
View 1 Replies
Ok I've got this 98 Ranger with the 2.5L and the 4r44e automatic. The engine is used and has about 100,000 miles now and is it a good state of tune - so I think. The transmission was a remanufactured I bought a few years ago that was built with the shift improver kit, Kevlar bands, extra planetaries, 4wd pan, and external cooler. It's now got 92,000 miles on it and it's been serviced every 30,000 with a fresh 4wd filter and Mercon V fluid. It's outlasted the last 3 transmission I've had in my Ranger. I've got 315,000 miles on the body. For awhile it was randomly losing power while driving like it wouldn't shift, almost like it dropped a couple cylinders, then as you kept your foot on the gas it would recover and rev up and shift.
Then sometimes randomly at stoplights it would shake at a stop and have no power at take off until it hits 30-40 mph. Sounds like a converter, is what I thought. But now it's doing it more often but not the shaking at stoplights as much as randomly losing power while driving normal speeds. Last night I drove it about 50 miles after doing a fresh filter and fluid change and this time it did it so much it threw a code up P1131. Even though that's a O2 sensor code, could it be hidden by a transmission valve body problem? One transmission shop said it could be a valve hanging up just by me describing it to him. Could this be ignition or fuel related or is it all tied in with the transmission problem, if it is even a transmission problem?
View 3 Replies
When I am at idle, the compressor keeps turning on and off every few seconds. It seems to work fine while driving. What do I need to do to fix this?
View 14 Replies
My compressor on my 92 Ranger did not have any clutches on it. Where they went. I got a compressor off of a 94 at the pick and pull. It was charged and the compressor turned fine. Brought it home and tried to install it. My hoses in the back of mine(92) are different than the 94. I went back and got the hoses, condenser and evaporator off of the 94. Put it all together. The high pressure hose on the 94 has some sort of switch on the high pressure side. What is this switch for and how can I wire it in to the electrical system on the 92? I assume it is some sort of pressure switch that allows the system to flow. I'm getting 30 pounds on the low side and 150-200 ponds on the high side. Also, when I increase the RPM's, the compressor kicks on and off. It's not like it would or should normally but fast.
View 7 Replies
I have a 2001 ranger 4x4 4.0 L with what appears to be a unique a/c problem. Over the last week the compressor will not kick on immediately and seems to randomly decide when it is going to function. Once it starts, it runs properly and cools well, until I turn the engine off and it is back to square one. We have checked the coolant level and it is full. the problem seems to be getting progressively worse....At first it took about 15 minutes for it to decide to trip, then 30 minutes, and yesterday I drove for over an hour and the compressor never kicked on.
View 4 Replies
I've got a problem with my AC Compressor, with the AC on the compressor engages then disengages about every 5 seconds. Now I looked into it and some people said you can remove a washer to remove a gap. Do you think I should change the whole unit? Looked online and I can get one for $100. If I do work on the AC compressor to try and fix it or remove the whole unit do I need to drain any refrigerant etc etc. I have a hayness repair booklet and they said that to remove the ac compressor you need to get it drained by professionals. Although on the compressor I only see a electrical plug and no hoses.
View 14 Replies
I have a 2001 Mazda B3000. The a/c compressor is coming on while I'm running my heat. The air coming out while the heat is on stays warm. However, when I was running the A/C during the summer the air would start blowing out warm after it had been on for a while. Several people told me it may have something to do with the blend door or blend door actuator but both appear to be working fine. What it could be?
View 1 Replies
So I just got done with my first 2 problems of the month with this truck last week. Front end and emissions along with spark plugs. Now, 4 days later this morning, I'm driving the truck trying enjoy the investment, and the AC compressor starts seizing up and burning the clutch. Unrelated but also worth noting, about an hour later the brake pedal gets real soft and the brakes get really sloppy at stopping the truck. The truck also stalled (auto trans) crossing a highway, luckily it was 5am and no traffic was coming.
I'm at $6k invested on a truck with 116,000 miles, and I've only put 6,000 on it. The repairs don't stop, and I've got many more ahead. Like rear suspension, axle, trans, and radiator fluids, and paint, to name a few. Any suggestions on fixing the AC before I drive this truck into a lake?
View 8 Replies
I am in the process of removing the lower intake on my 99 Ranger 4.0. I was unscrewing the AC Compressor to get it out of the way and also started to unscrew a bolt on the backside of the compressor because it wasn't moving well due to the metal tube on the backside. I think this is the tube to the condenser? Anyways it started spraying air and green fluid everywhere. I got it to stop for now but if I tighten or loosen the bolt it seems to spray. Also it looks like a green o ring or gasket of sort is showing now which I don't remember. What is it and what should I do?
[URL] .....
View 7 Replies
When I turn the control to heat the AC compressor kicks in. If turned to vent it does not kick in. Was this just a design flaw.
View 3 Replies
I have a 2003 ford ranger xlt 4.0L and here recently my ac compressor has been making a loud click noise engaging even though i am not using heat or AC, so when it engages the rpms drop and almost wants to stall and it does this in about 10-15 sec. intervals, but when I am driving it acts fine. What is going on here, I recently had a vacuum leak and i found it and fixed it, and now this issue just started.
View 2 Replies
This morning, I shifted into neutral and left the truck running. When I got in it put it in reverse, the shifter peddle went all the way to the floor and the clutch did not engage. I turned off the engine, and the transmission shifted easily. I put it into reverse, started the engine, and when I tried to shift back into first, the same thing happened. Pedal to the floor with no resistance, and I could not get it into gear. I finally forced it into 1st to get back into the driveway, but had to stall the engine to keep from going through the garage door. The clutch would not disengage at any time. I checked the master cylinder and it is 1/2 full. Has my clutch gone out?
View 14 Replies
I have a 1999 Ranger XLT 4.0 . The air is on all the time no matter what position the selector switch is in except "off ".
View 4 Replies
I recently got a 2010 Ranger sport 4x4, and the a/c seems to be working anytime the cold air is selected and any vent position.
View 3 Replies
The headlights on my ford ranger 1994 won't come off. All fuses are good and wondering the next step?
View 9 Replies
My sons 1998 ranger is in mph. Converting on to a kmh dash. There's one at the wreckers and I was wondering is it a direct replacement or is it a computer swap also? What years would work?
View 5 Replies
I own a 2003 3.o v-6 ranger, after a short or long drive, my truck has a hard time starting.. Starts fine before any driving..
View 12 Replies
Grandson 1991 Ranger 3.0 v6 69,000 miles We have a long start issue after it has sat for 30 mins. plus. If you open the throttle part way while cranking it will start fairly easily. Fuel pressure comes up instantly when you turn on the key. It runs at 39 psi pull the vac line off regulator it jumps to 49 psi. Fuel pressure does drop to about 30 psi after setting an hour. It kinda acts like it is flooded when it starts. so far we have done a complete tune up plugs wires cap and rotor. The ignition module has been replaced twice last one a real Motorcraft. New fuel pump and filter. Cleaned the fuel injectors with Ford cleaning system. I will replace the coil next and maybe clean the iac.
View 14 Replies
