Ford Ranger / B-Series :: 1997 Died And Won't Start
Oct 31, 2010
My friend's 1997 4 cyl ranger died and won't start. Cranks fine with no codes on OBD2. Was running fine before it died.
View 5 RepliesMy friend's 1997 4 cyl ranger died and won't start. Cranks fine with no codes on OBD2. Was running fine before it died.
View 5 RepliesI drove my truck 2 times the day it stopped running. The 3rd time I tried to leave it started moved about 2 ft, spit and sputtered and died. It had blown the fuel pump fuse. I changed it and checked the fuel shut -off in the cab, passenger side. It was not tripped. Tried to start it and as soon as I turned the key it blew the fuse again. I changed the fuse again and this time I changed the fuel relay and the switch in the cab. Turned the key and it blew the fuse right away. Went to AutoZone because they are close to the house described what it was doing to them and they said sounds like a short in the fuel pump.
I purchased a new pump put it in turned key blew the fuse, pump just clicked...I found this site and my son noticed a thread where it said wires under the cab are good for wearing through and grounding out. I looked and it did wear through one wire coating. We taped it up, put extra cover over it and now it does not blow any fuses. Fuel pump still just clicked. Took fuel pump back for an exchange.....same thing. Turns over but fuel pump will not pump fuel. What am I missing?......
I was driving my 85 2.3 liter down the road and it died all of a sudden like and wont start back up. I took out a plug to check for spark and had someone turn it over and I touched it to the big metal part the grill connects to at the top but I got nothing. It IS getting gas. The spark plug was white as if it was really hot and rough-looking for its relative newness. I bought a new distributor cap because it was corroded, but it didnt work. They tested the ignition module at the store and its good, so I am thinking distributor?? Also, could compression issues keep it from sparking? I am a little worried it got over-heated somehow, but don't know....
View 9 RepliesI am working on a 96 Mazda b2300 auto 2wd for a friend. His son was driving it when a loud noise, it died and wouldn't start back up. He had it towed to my house, I started to tear into to it and found it slipped the timing belt. So a rebuilt head, gaskets, timing belt, fuel injectors, water pump, thermostat, plugs, and fluids; tried to start it and nothing. Started troubleshooting and found the primary coil pack was out of spec, replaced and still nothing.
Changed out the CKPS still nothing? I have spark, I have fuel, I'm going to check compression tomorrow but the way the cylinders and pistons looked I don't think that is the issue but I going to check anyway, rechecked the timing marks they all lined up. Checked the fuel inertia switch not tripped. Could the PCM, or ICM cause a no start, and still be able to get spark and fuel?
My son's 97 2WD Ranger with 2.3L, 5 speed, no a/c, basic XLT standard cab.
I was using his truck because my 93 Ranger was getting a new starter on it. I drove to work with no problems, then after work, it started just fine and drove a few hundred feet to a stop sign where it promptly died. I was able to start it again with some effort and drove to the next stop sign maybe a quarter mile away. Truck died again, but this time it would not start. Towed it home about seven miles and its in the driveway now. The previous owner had new Motorcraft platinum plugs and wires installed, new fuel filter, fuel injectors cleaned, all about 11,000 miles ago. My son has had it for about 6,000 of those miles.
It felt like it ran out of gas, but the gauge showed about 1/4 tank, and I put about 3 gallons more from a gas can into the tank with no change in being able to start it.
Here's what I've checked so far according to my Haynes manual:
Turned key and listened for fuel pump and it seems to go on just fine.
Checked fuses and they are fine.
Swapped around relays in distribution box with no change
Checked resistance at coil pack and it was about 1.7.
Checked resistance at one injector and it was about 1.7.
Checked inertia switch and it did not need a re-set.
I don't have the ability to check fuel pressure.
I have a 97 ranger with 3.0 it runs great but once you drive it and shut it off and go to restart it it will turn over but not start it used to start once I let pressure off the fuel rail, but now is a little harder to start when it does this but it looks as thou coolant comes out of the reservoir when this happens I think it might be coolant sensor or thermostat problem causing the timing to advance until it cools but then again why was it starting when I released pressure from the fuel rail and also I don't believe my check engine light works...
View 8 Replies1997 2.3 Ranger w/ 160,000 mi. Every few months it won't start, sometimes after just having been running fine. Symptoms:
-the dash lights will be dim or off completely
-the chime will be softer than normal
-the headlights will not work, or be dim
-the starter will sometimes briefly click, sometimes crank once, sometimes do nothing
-the emergency flashers will sometimes click much faster than normal
-if during one of these "episodes" it does start, the battery light will sometimes flutter on and off, and the meter will flutter a little higher than normal. The next time I stop it, it typically will have the same problem.
-it will typically start if i get it jumped
My battery, starter, plugs and wires are all fairly new. On occasion, when it is having this problem, and I am trying like crazy to start it, if when I turn the headlights on and they are no longer dim, it starts right up and runs fine.
997 2.3 TruckSo this has been an issue for a long time, actually one of the issues I had when I got the truck 3 years ago. After it rains or is extremely humid, my truck does not want to start. Sometimes it will after cranking and cranking and cranking for a while (stopping to cool the starter of course) and other times it won't start.
This time around, it won't start. I cranked it for a little bit and had my dad check for spark while cranking. No spark at all. What should I start looking at? Coils, crank sensor and wires are all newer. As mentioned before, EEC has been replaced. Could it just be bad luck and I got a crap crank sensor? All fuses and grounds are good.
No codes, either except for the occasional misfire code that I get for some reason after pushing in the clutch to decelerate from a higher RPM. It'll fall and start to misfire, but clear up when taking back off.
My 2001 2.5 manual suddenly died. The starter turns the engine over, but I don't get a) fuel (changed the fuel pump) b) spark c) Engine check light. When I plug the OBDII reader in, it simply says "ERROR". No codes, no other language.
While trying to figure it out this morning, after trying to start it 50 times, it actually fired for a few seconds, but then died again.
I checked relays and fuses and nothing seemed bad. I swapped relays around too.
I unplugged the battery, then the computer, but nothing got it to fire again.
My Father in Law's 95 Ranger, 4 Cylinder, 5 Speed has started acting strange. It has, in the past 3 weeks just died suddenly, and won't restart. No action at all when you turn the key, as if the battery is disconnected. Wait for 45 minutes to an hour, and it starts back up again.
He has had it to a local shop twice, and the only thing they have done is let it idle for 5 hours at the shop. Of course, it never stopped.
Now they are saying it is the clutch, and depending on the type of clutch, (big or small).
I've been working on cars most of my life, and even had an 87 Ranger, and I've gotta call BS on this. He says it happens mostly when coming to a stop.
98 Mazda B4000 4.0 4x4
I bought this truck about two months ago and it has been great no problems starts right up and runs like a top. I was installing a 4 channel amp yesterday on and off and the dome light was on all day as the doors would periodically be opened or closed so it never did that cycle of 10 min or whatever when the lights turns off. This is what killed the battery.
I had my neighbor jump me and after a few minutes of charging it started right up and idled for about a minute long enough he left and parked, then it stalled. I started it about another 6 times before the battery died again. Every time it started fine then would idle between 1-10 sec then start to sputter and eventually die. Pressing the accelerator pedal only killed it faster.
I got a new battery today as the other charges so that I could fix it today without missing work again tomorrow. Unfortunately it does the same thing I was hoping that the voltage was just low or the polarity flipped or something on the other battery.
To sum it up the truck never gave previous symptoms just simply ran too low (battery never DIED the lights came on just clicked when starting) on power and now stalls when started which it does immediately no long cranking.
The twist; truck has an aftermarket alarm by Python. Problem is I don't know anything about the alarm or if it comes with an immobilizer. I am in the process of trying to figure this out but need to pull dash or something to find the "brain"? Never had an alarm like this I disconnected the clear square that adjusts the sensitivity hoping that was it but I don't know where or what I assume the brain of the alarm is.
So a couple days ago I started my truck and it fired up like normal, but then sputtered out and died after a few seconds. I tried starting it up again and it did the same thing. I tried once more and it started up fine and I drove away.
It sounds like my truck is running out of breath or something and just sputtering out. Runs fine once it turns over though. My issue is that it is happening almost every time I start it now. I have to turn it a couple times before it catches. What this might be?
Well it all started when I was having starter issues my starter died and my solenoid was just clicking and after time there was no power at all to anything in the truck i have replaced the solenoid and starter and check battery and cleaned post and terminals. I am going to replace my negative cable as it was pretty bad but if this still does not work, so what to look for. The truck is an 87 ford ranger 4x4 5 speed with a 2.9....
View 9 RepliesI have a 92 ranger 6cyl 4L. The truck stopped running while driving then kicked on again, it did this several times over about 20 minutes then finally died and now I can't get it started. I recently replaced the fuel pump and filter and spark plugs and wires. I get spark if I ground the plug and some gas will pour out of the fuel pressure test valve when I stick a screws driver in. When I check engine codes I get an all pass. Truck will turn over and sometimes run for 2 or 3 seconds but that is it.
View 2 RepliesI recently purchased a 1997 Ford Ranger with a blown 4.0 with a 5 speed , I have a 5.0 with a Carb and 5 speed out of a 80s mustang . Is it possible to use this in the 97 Ranger , I understand I need a different fuel pump but motor mount wise I was hoping it would fit.
View 2 RepliesWent to work one day and went to put my truck in park and it went as far as reverse. It has alot of play in the shifter. I have had a couple of people look at it and said that they would not touch it because of the air bag. I am not afraid to work on it myself if I just knew what to do. I am a single mom and on a budget, I would rather do it myself.
View 6 Replies97 automatic 4x4 SXT 4.0L. 4Hi will engage, but when I shift to neutral, press foot on brake, and shift to 4lo, nothing happens. No light, no sound. Occasionally it will make a sound, and even more rarely will light up, but it does not feel like 4Lo is engaged even when indication says it is. I pulled the shift motor and replaced, as well as verified that the transfer case could be shifted to 4 hi and lo by using an adjustable wrench. I have not put truck on stands yet, but I'm pretty sure 4 hi is truly engaging. I did attempt to engage with shift motor connected electrically but not mechanically, and it shifted. What is keeping 4 Lo from shifting? If it's a vacuum issue, wouldn't 4 hi not shift? I did check the vacuum lines and the vacuum reservoir and they seemed to be okay.
View 3 RepliesWent to start my truck up about 3 hours ago to take my ol' lady to work. Turned it over and acted like the usual cold start. Well soon as I thought it was good to let the engine spin, it got to about 300-400 RPM and then died. So I shut the vent off and turned my head lights off (turned them on soon as I thought it was good), spun the engine again and when it hesitated once again I gave it some gas like you would on a carb (not pumping just gave it half throttle or so) brought up the engine to about 3K and it ran just fine.
I'm not sure if its the fuel filter (when the last time my dad even bothered to change it since he has done most of the work on it in the time we've had it) or if the fuel pump is going out for the 3rd time in the last 10 years. The last time the fuel pump went it was a bad Walker fuel pump. It was promptly replaced with a Bosch and has been going strong for the last 8 years or so.
If it is the fuel pump, my guess is either my dad is going to junk it or fix it. With it getting close to 260K miles its becoming warn out and showing its age. Been pretty dependable and will do just about anything you ask and it'll do it even if it takes a long time to get going.
The fuel lines are pretty rusty so if its the filter chances are we'll have to put in a new section of fuel line in. Its probably running close to 135K miles on it since it was last done. I've only started doing maintenance on it the last 6 years or so for the most part.
First of it's a 2003 with the 4.6. I replaced a bad alternator a couple months ago and all was fine. On the way home today the radio volume went quiet and all the dash gauges were dead. Truck died and wouldn't even try to start, no starter clicking or anything. A couple times the gauges did the "sweep" but still no start, not even a starter click. Barely even operated the hazard lights. Towed it home and hooked up the jumper cables to my 7.3 Excursion. Truck started right up and I left if hooked up for a couple minutes hoping to get enough charge in the battery to get it in the garage.
Unhooked the jumper cables, got in the truck and noticed the voltage gauge was reading nothing, tried to move it and it died. Hooked the jumper cables back up and let the Excursion charge it for about 5 minutes. Started, drove it to the garage (100ft) and backed it in. Noticed the voltage gauge was where it should be. Turned it off and back to run (didn't start) and the voltage gauge was reading good and it started right up.
Now, it doesn't appear that the battery or alternator is bad. Is there something else I should be looking at? I can take the alternator off and have it checked but don't want to go through the work if not needed to chase a ghost. Advance auto Tough One alternator BTW.
I have a 1997 Ford Ranger with a 4.0L 2WD. The check engine light just turned on with a code of p0133. I know that this is something with the bank 1 sensor 1. I tried doing some research and I think that it is on the passenger side before the cat converter. Now, I don't know what to do from there. How do I go about fixing this? What part do I need? How do I fix it?
View 1 RepliesI have a '97 Ford Ranger with an automatic transmission that wouldn't shift out of park last night. A friend opened the hood and jiggled the steering column some, and finally it shifted. We checked the transmission fluid and it is full, a dark brown color. What the problem might be?
View 3 Replies