Ford Ranger / B-Series :: 1997 - Whistle Noise When First Accelerate And Slow Down
Mar 27, 2013
I have a 97 ranger 4 cyl that's been making a whistle noise the last few weeks. The sound is literally like a whistle and the noise level varies but its never obnoxious or loud. The sound does not happen when truck is idle, seems to happen mostly when I first accelerate and slow down although sometimes it does happen when I am going 20-30. it doesn't happen all the time but lately its happening more. What this could be? The truck idles and runs great.
View 14 Replies
Advertisement
Whenever I slow down for a car to turn or accelerate after a stop sign the ice cold air goes away and is replaced by warmer air but then it never turns back cold. Only when I kill the engine and start back up does it return. I just had the Freon refilled and there are no leaks.
View 3 Replies
As said vibration at idle, as I slowly accelerate (in park) the vibration is worse at 1200 rpm, then keep slowly accelerating and at 1800 rpm completely goes away. Doesn't seem like a miss almost like a balance thing. Also when in gear and accelerating it doesn't seem to be there unless I just don't feel it when moving.
View 5 Replies
I have this 03 3.0 flex fuel that as of lately (2 months) has developed a whistle when throttle is pressed half way or more.... not sure what or where its coming from..
View 2 Replies
So I have a 1990 Ranger XLT 4x4, 2.9 v6. My issue is I am getting a loud constant whistle sound on the drivers side, just in front of the rear tire. It is not from the tire and it is a whistle not a whine. The truck is all stock nothing special. I do not have an exhaust anymore only a cat. Anyways the sound is constant an does not get louder or quieter while moving or in neutral it just stays the same. It just started in the last few days. Also the truck is a Manual.
View 3 Replies
Just bought this truck and no check engine light was on, went to get it smogged so I could register it and it had the following fault codes: P1443, P0401, P1131, and P1132. The truck seems to run great in my opinion and even gets really good gas mileage. There is a whistle intermittently from the intake manifold area though that is at times pretty loud.
Smog tech told me these trucks are "notorious" for the check engine light going bad and that usually the entire instrument cluster has to be replaced in order to fix it. I'm a very experienced motorcycle /small engine tech but do not have much experience with car/truck engines and especially not with emissions control systems.
Again it is a 1996 Ford Ranger 4.0 V6, 4 wheel drive STX with 185,000 miles on it. Where to start or what might be the source(s) of these error codes?
View 5 Replies
I have 2005 Ranger 4.OL just recently when I accelerate the battery light comes on. No light when driving normal. Stopped by O'reillys had them check the battery, alternator, starter. They said battery bad. So I dropped 130.00 on new battery. Light still comes on when accelerate.
View 6 Replies
I am first time ford owner of a 2003 ford f150 super crew fx4 with the 5.4 Triton and lately when I accelerate hard and it down shifts. It shifts excessively hard or when your going slow and the have to accelerate it also shifts really hard i dont know if it is the diff the U-joints or if its the transmission.
View 4 Replies
My ranger is an 89 but it's got a 91 motor in it, 2.9 V6. When I accelerate it hesitates before actually accelerating which makes me think the TPS is bad. Probed and tested and I got .85V throttle closed and 4.65 at wide open. Specs call for .8V - 4.5V
I'm not sure if there's an allowance of fluctuation, but is that high enough to point out a bad TPS? If it's not the TPS, is the ignition timing off or what else could it be?
View 8 Replies
I have a 1999 ranger 4x4 , when I'm going to a slow final stop the abs kicks in ,doesn't do it every time , there's no abs warning light , took it to the ford dealer they scanned it and said it was the left front hub & bearing assembly, said the sensor wasn't reading the back of the bearing assembly. I can't understand way the abs light isn't on, is there anyway to clean that they want to replace the hub & bearing, Is a use hub & bearing replacement a good way to go? They told me I could pull the fuse and kill the abs, but I find three fuses I pull aII three and got a speed sensor check engine code. I hate to replace that hub & bearing when there's no problem with the bearing ,Is there any way to deactivate the abs, by the way it's 4 wheel abs.
1999 FORD RANGER 4X4 4.0......
View 14 Replies
My overflow tank seems to be going empty slowly. The last time I filled it was in March and I filled it to the Full line. Now, the overflow is almost empty. I did 425 KM last night almost non-stop and the level stayed the same since that night and today. So, I am not burning any thru the gaskets. Exhaust is not white neither.
I did see one suspect thought. I have this really small rad at the bottom of the bumper and it seems a little wet around the tubes that enter it. Could it be that? I have no spots on the driveway or road when I park. Specs of my truck:
190 000 KM.
Oil changed on Saturday.
Runs well, no loss of power.
Temps are good.
View 3 Replies
If I hop in my truck right now (1994 3.0 ford ranger 5 speed) as soon as i accelerate half pedal or more it'll bog down really bad. Usually in second gear it does it the most and ill shift to third gear and it still jerks and has trouble accelerating. If I let the car sit for 10 minutes and then go drive it it'll jerk and bog down a little bit but no where near as much. usually only does it for the first couple minutes of driving then goes back to normal. I also noticed that my temperature gauge is always right before NORMAL. Also I'll have to give it a little more gas right before i go to drive or it'll want to stall but as soon as i get into driving it, it acts perfectly fine.
View 7 Replies
i have a 02 ranger 4by4 with 4.0.every time i try to fuel the pu it spits gas back out the fill tube and i have to fill it very slow to get fuel in it.i just replaced the filler neck about 6 mos ago due to having a hole in the the hose by the local ford dealer,
View 6 Replies
I noticed that my ABS was engaging when I would slow down to a stop while turning left. I pulled the fuse for the ABS just to make sure that's what was causing the pulsating brake, and it was. Anyway, if it's an ABS sensor problem, would it be the front passenger side sensor if it's only happening when I turn left? Is there a way to test this. Would a scanner detect it? It hasn't been throwing a code or anything. Just the ABS engaging while braking and turning to the left when it shouldn't be.
View 6 Replies
I have an 87 Ranger and the oil pressure gauge is slow to respond changes in pressure. Is this the way the gauge is designed to work or do I have a bad sending unit?
View 4 Replies
'94 Ranger with aluminum wheels.
I have problems with slow leaks and vibrations from multiple wheels. Both problems have persisted through multiple tire changes over the years. The same shop has always done the tire changes and they tell me they've been balancing the wheels and cleaning the inner rims. The vibration went away after putting on my B2 wheels. Then swapping the rears back to the ranger wheels, 2 at a time, the vibration was back for both test drives (hence vibrations from multiple wheels).
The wheels are badly corroded at the rims and valve stems which leads me to believe it's the wheels themselves that are causing the leaks. I haven't heard of excessively old wheels causing vibrations though which is why I ask. I will likely be buying some craigslist or junkyard replacement wheels but wanted to "check in" first.
View 10 Replies
This has happened 3 times.
1st) pulled quickly over to side of road, shut off truck. It would not start then. Towed it to service station and it started the next morning (with no repair made). I wonder if tow ride dislodged the the blockage in fuel line(?). Always sounds like it's going to turn over, but like not getting fuel.
2nd) Went to leave work, truck wouldn't start. Towed to my mechanic and he replaced fuel pump. Thought it was fixed because it ran fine until just the other day.
3rd) Slowed down to complete stop in heavy traffic and it stalled. Would not restart. Again sounded like it was going to start but didn't seem to be getting fuel. Good samaratins pushed me off road. Had it towed to mechanic. Started the next morning without any repair or service. It's like the tow ride and bumps getting it off the tow truck dislodges what ever is blocking the fuel line.
My mechanic replaced the fuel pump, but I don't think her replaced the fuel filter.
View 6 Replies
I have had my 1998 Mazda B2500 truck since 2000 and this problem comes and goes (it's mostly been gone lately). Usually when it is cold outside. At slow speeds it creaks and squeaks - kinda embarrassing - if I am sitting still it squeaks when I turn the steering wheel. Once the speed picks up you can't hear it. I have noticed this in other fords about the same year.
View 1 Replies
I have a 98 ranger, 4x4, 5spd 3.0 with 88k miles.
While I am driving it, everything is great, but when i start to accelerate, or torque the engine (going up a hill), I get this clicking/vibration in my gas pedal. its extremely noticeable, by feeling and ear.
Its most common around 2k to 2.5k RPM. There is a lot of play in the throttle cable, about an 1" or so give untill you feel pressure. What I need to replace or tighten?
View 1 Replies
One last issue with my 2000 B3000 3.0L. The leak seems to be on the left (passenger) side of the water pump very near where the bottom radiator hose connects to it. I can't find any loose bolts. It does not leak while driving the truck or soon after. It has to sit for several hours or overnight before it shows up. There are usually 3 or 4 wet spots where it drips from the water pump to the frame to the driveway. It is small enough that I only have to fill up my coolant tank every 1 or 2 months. Could this just be a small gasket leak? It's been happening for about a year or so I think. I replaced the radiator about 2 years ago. I've been expecting it to get worse or bust loose and have been checking it very often. I've never seen one not leak while running like this-has me puzzled.
View 6 Replies
1988 Bronco II 2.9L Issues:
- When I turn off the wiper switch the wipers immediately stop in place, they do not continue to their normal 'down' position.
- The switch's adjuster to slow the wipers isn't working, only the low and high settings work.
What I've done so far:
- Replaced wiper switch with used from spare parts.
- Replaced wiper switch with new from spare parts.
- Replaced wiper motor with remanufactured from Autozone.
- Thoroughly cleaned wiper motor ground terminals.
- Replaced interval wiper governor with used from spare parts.
The problem occurred after the truck sat in my garage for 6 months while I removed and reinstalled the engine to replace some gaskets & seals.
View 6 Replies
