Ford Ranger / B-Series :: 1997 - Vibration Feels Like Wheel Hop
Nov 25, 2016
I'm having a bit of an issue with my 97 ranger 4.0 auto 2wd. I have an vibration which from a stop up about 10 mph feels like wheel hop not bad but you can definitely feel it it and over 50 mph the whole truck starts to shake again not bad but you know its there. the truck sat last summer it was my dd till a bought a new car and now vw is buying it back ill be driving the ranger in the mean time. I have been trying figure it out for a few months but no luck i have put new tires , front rotors and rear drums , drive shaft support bearing ( 2 pc shaft) new u-joints and a used boneyard shaft with new u-joints as well, checked the tail shaft bushing which had about .008" of play.
Pulled the drums Off today and checked the axle bearing for play only .004" of play pulled the diff cover and checked for carrier play as well as pinion play but can't find anything. I'm at a loss here and looking for other things to check ... Don't know if its possible that something in the transmission is loose it was rebuilt about 75k miles ago I was going to stop and talk to the trans shop to see what he thought (its a 5r55e ) ....
View 14 Replies
Advertisement
I recently replaced the oil seal on the front differential where the front drive shaft connects to the diff. I believe it is called the pinion oil seal. I had to remove the drive shaft to do the job. Got the oil seal in place and then slipped the u-joint yoke on and hand threaded the retainer nut on to get it started. I did mark the relative position of the drive shaft to the front yoke and the rear yoke. I had previously noted that the retaining nut, before I took it off had about 2.5 threads showing. I had to remove it with an impact wrench.
So...I used the impact wrench to put it back on with about the same number of threads showing. I then reinstalled the little short fronmt drive shaft...the one that comes out of the transfer case. I got the front of it on to the pinion output on the front diff...and then had to reattach it to the transfer case end which, by the way an interesting affair with a sort of metal cone that is attached by 6 8mm fine threaded bolts about 2.5 or 3 inches long. Got all that done with much grunting an groaning - I'm laying on the ground - SO the oil, leak is fixed but now ...
There is a vibration at around 40 mph and higher. like something is out of balance. did i damage the front diff pinion bearing by using an impact wrench? this vibration occurs in 2 wheel drive. as i understand it the front drive shaft doesn't even turn when in 2 wheel drive. my question is does the front diff gears spin when in 2 wheel drive? perhaps the u-joint is bad on the front drive shaft? just a bit baffled. when the speed drops to below 40mph the vibration goes away...
View 2 Replies
As said vibration at idle, as I slowly accelerate (in park) the vibration is worse at 1200 rpm, then keep slowly accelerating and at 1800 rpm completely goes away. Doesn't seem like a miss almost like a balance thing. Also when in gear and accelerating it doesn't seem to be there unless I just don't feel it when moving.
View 5 Replies
My speed control has not worked in years and I do not use them any more any way. I want to remove the control area on each side of the steering wheel, the covers are all messed up so I would like to make it look like it came without them. Can I do this and if so how?
View 1 Replies
I have a '98 Ranger 4.0L SuperCab 4x4 Automatic
The other day i was driving, around 40 MPH and suddenly the truck felt like I hit rumble strips on the highway, I hit the brakes and when the truck got down to about 10-15 MPH, it went away. It didn't feel like an out of balance tire or anything like that. It felt exactly like I hit rumble strips. It was a strong, high frequency vibration. I then continued on my way, and it was fine for a little while, still doing 40 mph, then suddenly out of nowhere the same vibration came back. Once again, I slowed back down, it went away and stayed gone even when I sped back up.
Both front hub bearings are less than a year old, and a quick check of the driveshaft seemed to indicate the u-joints are still tight. Front diff/driveshaft turns freely and smoothly and the front hubs are not locked.
'm going to try and jack the truck up and check everything thoroughly, but I'm really at a loss here, as I've never experienced anything like this before in any vehicle. Some reading suggests that it might be transmission related to the 5R55, but I'm really unsure.
View 11 Replies
I have a 2010 Ford ranger sport 4x4, manual, and when backing up at a decent speed, then press the brake to slow up then depress the clutch, the brake pedal pulsates and it feels like something is grinding. It has happened in first once, but I can make it happen in reverse anytime...
View 1 Replies
I have a 2000 f150 lariat. Mo problem started about 2 weeks ago. Around town its fine but when I go over 50 mph it feels like I'm driving down the rumble strips on the highway and after a couple miles it just smooths out and its fine! Yesterday I went on the interstate and it did the same but this time I ran up to 85 and the vibration stopped.
I had another motor put in about 2 months ago, #4, and he changed my rear u joint as well. I replaced the rear passenger side wheel bearing a couple months ago but there seemed like a little play in the axle still but not bad. I've been to the dealer and a few other mechanics but it doesn't do it all the time and they couldn't find what is wrong.
View 6 Replies
vibrates on slowing down - no brakes just let off gas - until speed drops down to fairly low. an auto trans. seems to be front end source, the driveshaft and u-joints appear good. I jacked up front and checked tie rods and wheel bearing shake - nothing there?
I haven't found a long enough downhill grade to try it in nuetral selector position at over around 25 mph yet. Could shock absorber do this? They appear good. tires have some miles on them but wheels have the weights on them?
View 14 Replies
I just totally re-built the rear brakes in my 93 Ranger 2wd. Now its seems I have this 'intermittent vibration' between 90 to 105 km/h.
View 7 Replies
We have a 2000 ranger 2wd with a 5 speed transmission, we just had new tires put on last Sunday and on the way home it had a vibration in 5th gear at 55 mph whats so strange about it is, in 4th gear at 55 mph. it don't do it but when you shift it to 5th and hold it at 55 it starts.
I have checked the drive shaft and even put it on stands and shifted through the gears and held it at 55 no vibration, I guess because there is no load on the drive train. the truck only has 56,000 miles on it.
View 9 Replies
he has a 2009 ford Ranger, 2.3L .with 54thou miles, the Issue is Vibration during in gear and stopped at a light no vibration at higher rpms during driveing, he states vibration happens in park ,neutral,reverse and drive. had the truck in for repair in two separete dealers they couldent find the problem its an automatic trans. he states from day 1 this truck has had the prob now its out of warrentee.dealer told him that trans to engine alignment was the prob dealer did some alignment and worked for a few weeks.
View 10 Replies
In my 2006 Ranger XLT, 4.0L V6, 2WD Manual; I am getting vibration from what appears to be the passenger front. I have so far replaced the front wheel bearings (both sides), replaced front shocks and checked rear shocks, rotated tires (to see if it changed) and had front tires balanced. I've also had a friend follow me on the freeway and check the wheel to see if is bouncing, wheel appears to be glued to the road. I have done all the front suspension checks I can and find no indications it is the lower ball joints or tie-rod ends.
This vibration is very in consistant, in different lanes it is better/worse. At times I feel it more in the steering wheel, others my seat and at times the gear shift. I don't believe it to be the engine mount(s) cause when it is vibrating I can shift into netural and the vibration does not change, I have also performed the 5K rev (FORD maitn. manual) and the engine is smooth (along with my expierence with bad mounts in my '94).
View 11 Replies
Bought a 02 Ranger, 4.0 4x4 super cab 122,000 miles. etc Picked it up for 500 bucks because someone scrapped it along the side of a guardrail this last winter. Replaced rack and Pinion (cracked), Tie rods, Shocks, driver side knuckle and wheel bearing, and some body issues (bed is still shot so if any black short bed sitting around let me know). I've been kind of putting around all day in it, letting it used to working again. Starts right up, turns easily, I string aligned it so it goes where I want.
But as I get up to speed start at about 10MPG there is a vibration based noise coming from the front, can't pin down if its left or right. If Im going straight then turn it gets slightly more intense as I even start turning the steering wheel. The noise increases with vehicle speed. And I don't know if its separate or related, but any turn over 5-10* to the left results in a grinding sound but then I turn to about 10-15 and it gets less intense. No noise turning right.
I'm thinking a bad CV, TWO bad CVs, or a bad differential. Before I start ripping into those things, thought I'd get opinions, or hopefully experience in this area. I'm really hoping its something small and stupid. (like not getting a professional alignment)
View 6 Replies
Have a 99, ext cab, 3.0 , 5 spd man. 125,000 on it. I know the clutch will need replaced shortly but so far it is still functioning with out the slipping. Although I can feel a slight vibration, or buzz when I up shift. My immediate concern is the clattering/rattling. say at idle, not moving with the clutch pushed in when I shift into 2nd and 4th gear it really rattles loud. I can only assume it is some bearing inside the transmission, but need to have a bit more surety as to the problem. I know, I need to do the clutch however i don't know if the transmission is going bad or is that noise in the clutch area.
View 2 Replies
1999 Ranger xlt, 4 cyl. 2wd reg cab, automatic. Getting a rumbling noise with some vibration in the floor ( nothing in the steering wheel, does not seem to affect handling ) runs consistently and relative to speed of vehicle......can not isolate or determine origin of noise.........
When initially driving car after sitting for awhile, the noise does not kick in until 50 to 100 yards have been traveled but is consistent thereafter,.....except for.. completely disappears during taking of left handed curves at good speed but reappears when road straightens...... right-hand turns have no affect positive or negative.
Have thrown into neutral at speed and sound and vibration is unaffected,.... brand new tires ( needed them ) with balancing had no affect either Struts, shocks, springs?
View 4 Replies
So my ranger was having a textbook wheel-bearing noise at around 50mph....when I turned to the right the noise went away implicating a passenger side wheel bearing.
So I replaced both of the hub bearings on the pass side and noticed that the front axle shaft u-joint right behind the spindle was really bad and was going to change it but couldn't get the spindle off so I said screw it.
Took it for a drive and the noise is still there. Could a worn u-joint possible replicate a wheel bearing noise? I am used to them making a clicking/popping noise while turning when they're bad, but not a whirring sound.
1993 ranger 4x4 manual locking hubs.
View 4 Replies
I recently bought a 91 Ranger 4wd for my son. The guy I bought it from put new manual lock outs on it. every time I take the tire off on either side the hub comes with it! Is there a clip or retainer missing? If so what and where can I get one?
View 4 Replies
I have a 98 ranger, 4x4, 5spd 3.0 with 88k miles.
While I am driving it, everything is great, but when i start to accelerate, or torque the engine (going up a hill), I get this clicking/vibration in my gas pedal. its extremely noticeable, by feeling and ear.
Its most common around 2k to 2.5k RPM. There is a lot of play in the throttle cable, about an 1" or so give untill you feel pressure. What I need to replace or tighten?
View 1 Replies
'92 Ranger 2WD with 4 cyl and 9" brakes, right rear wheel cylinder keeps blowing out, replaced it twice. I've thought about maybe an obstruction in the left brake line creating too much pressure, or in the junction block on the rear axle. I believe only one line leads to there from the master cylinder, so what else could it be? Only other thing I can think of is that the right brake has a mechanical problem which is causing the forward shoe to move too far away from the cylinder, leaving no 'stop' so the piston just slides right out of the cylinder. But I can't figure that. Original adjuster star wheel was chewed up so I swapped in another, doubt it's that.
View 14 Replies
I bought a 99 ranger few months ago cant the 4x4 has not worked in the truck for about 4 years. Bought it off my dad. He hasn't figured it out the t case locks in the drive shaft spins but hubs will not lock in. Has new hubs in it and still not working. Trying to get it fixed so I can park the diesel for the winter and run the ranger.
View 3 Replies
I recently purchased a 1997 Ford Ranger with a blown 4.0 with a 5 speed , I have a 5.0 with a Carb and 5 speed out of a 80s mustang . Is it possible to use this in the 97 Ranger , I understand I need a different fuel pump but motor mount wise I was hoping it would fit.
View 2 Replies
