Ford Ranger / B-Series :: 1997 - Replaced Thermostat Still Overheating?
Jun 1, 2012
Bought this truck at auction a few days ago. Started drive home and noticed temp gauge almost pegged full hot. Stopped and left it and pickup up later that day with trailer. Got home and started and ran it. Will not overheat at idle. Gauge fluctuates between full cold and 1/2 at idle. Rev up and temp drops to full cold. Drive around town under 35 and it stays between 1/2 and 3/4. Get on the highway and Pegs full hot. Replace thermostat and flushed system. Lots of rusty water and chunks of rust/mud poured out.
Upper rad hose is firm and hot. Lower rad hose is warm soft. Bypassed heater core and still over heats. I can run water hose from top hole on radiator and water crosses threw radiator and pours out the bottom so I don't think it's clogged. It's not the head gasket, I have no smoke, no milky oil and no oil in coolant. Fan clutch seems fine, I can spin it with the engine off and feel resistance. Truck hasnt boiled over while running hot so the gauge may be wrong. If it means anything the truck runs very rough and pulled up a misfire on cylinder #1 and had a iac code.
View 14 Replies
Advertisement
My engine started overheating, and because I was stuck on a bridge during rush hour (George Washington Bridge in NYC), I couldn't get stop the car. I drove it for approximately 30 min (slow crawl), and this happened: [URL] .....
Yes, I know how stupid it is, but there was not even a shoulder to pull over to the side. The only good thing is that this happened pretty much soon as Igot off the bridge, and not on the bridge.
Hose by the radiator cap (is that the overflow hose?) popped out and spewed steam for good 5 minutes. The car did not start at this point. I left the car by the gas station after the bridge, and came back later on in the night. It started and I was able to drive it home (about 10 min away) at crawl speed without it reaching the red zone.
Today, I just did the oil change, topped off on the coolant, and also replaced the thermostat. But the engine still overheats (to the red). The upper radiator hose is burning hot and the bottom radiator hose is not. Also, the fan is working, but it blows out pretty hot air.
View 12 Replies
problem is the my 1998 Legacy (142K) overheated this past weekend. It shut off and I had it towed to a "new" mechanic around the corner from my house. He diagnosed the problem as being a faulty thermostat. He replaced the thermostat and returned the vehicle to me. Two days later my wife was driving home and the car had a major overheating incident with resulting serious mechanical failure. I did a little research and within about five minutes found that this problem is quite common for this car and is more commonly related to a head gasket issue. My question is should this mechanic be held responsible in any way for the misdiagnosed problem? If so, what would be the best course of action? The car was otherwise running fine and in fact I recently had the transmission rebuilt.
View 3 Replies
My son has a 2002 Jetta, we just changed the water pump and the thermostat. The car will sit at idle and the temperature will stay around 190. When you drive down the road the temerature will rise and when you let off teh gas the temperature goes back down. What this could be, I have tried everything I can think of to fix this car.
View 13 Replies
I replaced the fan clutch and thermostat on my 1999 5.4. Do I need to "burp" the system or anything?
View 1 Replies
So I noticed when I check the oil, there is a very small amount of water at the end of the dipstick and also water mixing with oil around the oil cap. It is not much water at all, but my first thought was head gasket. I was loosing very small amounts of coolant, but found a small leak at the thermostat housing....The truck runs fine, idles fine, no bubbles coming from the radiator at startup, no moisture from exhaust. It seems to be using more oil than normal, but I drive it 100 miles a day still and no major issues other than the perplexing bit of water and oil mixing. Could it be a tiny head gasket leak? What else would cause the water and oil to come together.
View 13 Replies
For a while now I've been having issues with my truck overheating. Generally when I slow down, come to a stop, after driving a while. The other I replaced the radiator cap, as coolant was bubbling out after driving far. Thermostat was replaced. Radiator was flushed today as there was some rusty color build up. Added engine oil as it was VERY low the other day. So far I'm still getting the overheating issues and it seems to happen more so when I run my AC. I've noticed no significant leaking from anywhere else after replacing the cap. I'm thinking of either the water pump or the fan? But I dont know how to know for sure and I dont want to replace parts that I dont have to as a waterpump alone is $50-60.
View 2 Replies
I have a real problem with 2000 Ranger, after changing the upper radiator hose and thermostat, I now have a pretty constant leak from the gasket between the thermostat body and engine. Appears to be something that is triggered by the thermostat opening, so whatever the leak, the thermostat is blocking it.
I've changed the gasket, cleaned the mounting surface as good as I could. Tried re-torquing the bolts, but on that score - what is the torque specs for the 2000 3.0 liter Ranger?
But ultimately, what the heck is wrong here? This should be a pretty brainless operation really. Am I tightening the connection too much and cracking the gasket? I guess that has just occurred to me, although the gasket is not as stiff as a typical fiber gasket is.
View 10 Replies
We had my son's water pump replaced in his 97 F150. It is now occasionally jumping to completely hot. If you turn it off and back on it returns to normal. The power to the engine is cut when it shows to be overheating. The check engine light has now come on.
View 9 Replies
I got a 1990 Ranger 4x4 2.9l that loves to get hot only when the ac is on. The engine was rebuilt by me about 2000 miles ago and I made sure to have the block boiled in order to clean out any crap that could've been built up in the water jackets. So far the radiator, cap, thermostat, and fan clutch have been replaced. The fan shroud is intact and the condenser has a few bent fins but not many.
Here in Vegas we're looking at 100+ from 10 am - 4 pm so the ac is a must. I could be sitting at a light all day with the ac turned off and the truck doesn't have an issue. When I turn the ac on though the truck almost immediately begins to get hot. The engine drops maybe 100 rpms and the voltage gauge also drops a little. At night if I'm running the ac the voltage drops to what looks like 10 volts.
While the ac is on there is an immediate loss of power as well. In my head I'm thinking a failing compressor, water pump, and alternator are at fault. It doesn't matter if the truck is moving either, the temp still climbs.I know the rangers are funky with their cooling so when I burped the system i turned the heater on and lifted the front end about 1 ft off the ground with the cap off.
View 14 Replies
I had to replace the tie rods in my mazda b2300 and the mechanic also replaced the brake pads.
Now when I drive, I can hear the pump for the brake fluid going on and off when I'm not even using the brakes and the ABS goes on a lot too.
He tried resetting the computer by unplugging the battery for a bit but it's still doing it.
View 2 Replies
I have to fix the truck. Battery is pretty new, replaced solenoid next to battery this morning. Truck still won't start, just clicking away. Decided I needed to replace the starter, put the truck on jacks and went to the starter. At the starter solenoid there is a red cable attached, and a "loose" red wire, with a connector on the end. It would appear the connector just needs to be reconnected to the solenoid. But it won't "connect". Am I missing something? Should it not connect to the prong on the solenoid? Should I just replace the starter, and forget about the wire? I do have Chiltons for our truck, but it doesn't show a picture of the prong on the starter solenoid.
View 11 Replies
I have a 2003 Ranger 2.3l with 327k miles on it. I recently replaced the belt and now it doesnt want to start. The belt is on correctly and tensioner is tight. The battery is fully charged its just not firing up and starting. All connections are good, the ac and power steering pulleys are relatively new. Now i have been stuck tryin to fix it for a week...
View 8 Replies
I replaced the clutch, slave, flywheel and pilot bearing. Now it sounds like gravel bouncing around under the truck.
Everything works beautifully, but there is horrible noise especially at idle. If push the clutch it will quiet a little. If I change the rpm it will get worse then quiet out then get loud again, there is a sweet spot.
What the heck did I do wrong. It's a horrible gravelly grinding sound.
View 7 Replies
I just finished replacing the Valve body gasket in my 99 ranger with the 4.0 liter v6 with the 5r55e trans. My problem now is that I have no gears i can shift it but the gears do not engage.. I did install the updated bonded separator plate and the tsb for the blow off valve with it.
View 6 Replies
Just replaced fuel pump and now it turns over but won't crank. I have checked the fuel rail. Pressure is fine. Checked coil pack I'm getting spark. Still won't crank. Checked inertia switch it wasn't tripped. What next? 2003 Ranger edge...
View 1 Replies
I have a 99 ranger with a 2.5L that keeps throwing the p1401 code. I have replaces the DPFE sensor 3 times (finally with the motorcraft one), the egr valve, the egr tube, EVR solenoid, DPFE Hoses, Ignition Coils and Gas Cap. I have scoured the internet trying to find an answer but it seems like people just continuously throw parts at it until the code goes away. What could cause the issue?
View 2 Replies
I have a 2011 ford ranger XL and I get no high beams. My low beams work fine but when I try to either activate the high beams or pull for the flash to pass they do not illuminate and the indicator on the dash doesn't come up either. I have replaced the fuse with a fresh one, even though it didn't need to be replaced, and also replaced the headlights as well cause one was burnt out.
View 1 Replies
The other day I was driving down the road on a long, flat section and all of a sudden my truck started missing out of the blue. Ever since it started missing it hasn't stopped. The truck is an '89 Ranger, 2.3l, 5 spd. The plugs and wires were replaced last year along with the timing belt and fuel pump. It has been running great since then until now. I thought maybe it might be a clogged fuel filter so I replaced that but it didn't work. Also, it doesn't miss all the time. It doesn't miss when its idling or if you are going down the road while it is missing and slowly release the gas pedal it reaches a point while you are letting the pedal up where it will even out. It definitely seems like it is an "under load missing" scenario. Also, the Check Engine Light is not on. Where should I start looking?
View 4 Replies
Ranger wont fire! fuel pumps not pumping..... Jumped fuel pump relay and got both pumps working, but while jumping relay and cranking motor, still no fire. Plenty of fuel pressure though. got spark too. Replaced relay and no pumps working while key is turned to run or while cranking. I got to get this sweet puppy back on the tarmac...
View 7 Replies
My Ranger had been shifting hard for quite awhile. I recently opted to go ahead and replace the clutch, throwout bearing, had the flywheel turned and replaced the pressure plate.
This just seemed to make the problem slightly worse. I thought it was possible that my master cylinder needed to be replaced (the slave was replaced two years ago and didn't appear to be leaking when I had the tranny off). I replaced the master cylinder and now the clutch won't disengage at all. I've spent several days trying different things to bleed the clutch, and I just can't get it to bleed. I took it back off and bench bled it, then put it back on and bled through the whole system. This isn't working. I've tried numerous suggestions-jacking up the back end of the truck, jacking up the drivers side of the truck, I even bought a vaccuum bleeder and used it for 2 hours just having an assistant fill up the reservoir while I sucked fluid out the bleeder valve. The best I could ever get was some resistance on the pedal, but not enough to push the disc away from the flywheel.
I took the pickup to Ford, they said they bled it and charged me 90 bucks and still couldn't get the clutch to release
View 3 Replies
