Ford Ranger / B-Series :: 1997 - Ran For About Ten Seconds / Stalled After Rattling And Now Won't Turn Over
Mar 24, 2014
I have a 1997 Ranger,4.0,4WD,auto,extended cab. It's always been a great truck. wouldn't start yesterday . I thought the battery was dead , put it on charger and it started right up today. It ran for about ten seconds, started rattling like crazy , stalled and now it won't turn over. Has 150,000 miles on it. Just had oil changed, No ticking or anything else. Drove it every day, just came back from 1000 mile trip.
View 12 Replies
Advertisement
I have a 97 ranger with 3.0 it runs great but once you drive it and shut it off and go to restart it it will turn over but not start it used to start once I let pressure off the fuel rail, but now is a little harder to start when it does this but it looks as thou coolant comes out of the reservoir when this happens I think it might be coolant sensor or thermostat problem causing the timing to advance until it cools but then again why was it starting when I released pressure from the fuel rail and also I don't believe my check engine light works...
View 8 Replies
I have a 2005 ranger SOHC 4.0 new rebuilt engine It starts then dies after a few seconds then doesn't start at all unless it sets for a few hours or over night and will do same thing. It has 60 psi on fuel rail, good spark I'm starting to think my PCM is causing all this?
View 14 Replies
SO ive been after this problem for a while now. When my truck has been sitting for 2 days or its a semi cold morning (35 degrees) the truck has a problem not starting. Ive changed the fuel pump, the starter (my starter was going bad anyways and I thought it could also solve the problem I was having), and the battery was just tested. If I leave my key on Acc for like 10 seconds then try to start, it starts right up or if I just re-start right after the first. Now I am leaning towards this being a fuel pressure problem but I am not sure where to start with that... My mechanic also said that it could be the wire that connect to the battery terminal because they can get corroded.
View 4 Replies
I have a 2000 Ranger step side and the bed side is loose and and I'm trying to figure out how to reattach it. It's loose towards the front of the bed on the passenger side right where the actual step is. Is there an attachment point underneath the the plastic step cover?
View 2 Replies
I've got a problem with my AC Compressor, with the AC on the compressor engages then disengages about every 5 seconds. Now I looked into it and some people said you can remove a washer to remove a gap. Do you think I should change the whole unit? Looked online and I can get one for $100. If I do work on the AC compressor to try and fix it or remove the whole unit do I need to drain any refrigerant etc etc. I have a hayness repair booklet and they said that to remove the ac compressor you need to get it drained by professionals. Although on the compressor I only see a electrical plug and no hoses.
View 14 Replies
The truck started acting up while driving. It would shut off (no miss or anything), but would start again. Now it is sitting in the driveway and wont run more than 3 seconds. The fuel pump has been changed and did not work. The fuel pump relay is new and did not work. I read that the fuel pump goes to another circuit after start up. Could it be running to start and then shutting off? Inertia switch is not tripped. Where to look next. 1992 Ranger 6 cylinder ....
View 10 Replies
I am considering purchasing a 1999 4x4 ford ranger. The original owner has receipts for everything done on it recently. Rebuilt transmission, New ac, New shocks, new tires. I have never owned a ford but I always loved my friend's ranger. The only problem I had with it was an occasional clunking/rattling noise when test driving. I have read and was told this can be a common problem.
View 1 Replies
So a couple days ago I started my truck and it fired up like normal, but then sputtered out and died after a few seconds. I tried starting it up again and it did the same thing. I tried once more and it started up fine and I drove away.
It sounds like my truck is running out of breath or something and just sputtering out. Runs fine once it turns over though. My issue is that it is happening almost every time I start it now. I have to turn it a couple times before it catches. What this might be?
View 11 Replies
1988 Ranger, 2.9, 5 speed, 2wd, 7.5, 3.42:1, 190K or 290K on the odo.
I've been hearing this rattling, sometimes kind of a metallic ping, from the rear the last week. I thought it was probably the universal joints, didn't do it often, only under load between 1500-1900RPM roughly in second, third and fourth. I planned on working on it this weekend.
Today it started really making noise, sounds like valves rattling as though the timing was too high but it was coming from the rear end. It was making it all the way through the gears into fifth, even when cruising. Once it cooled down a bit it nearly went away.
I'm going to get started on it as soon as I can, but I can't get it in the shop to pull the differential cover and take a look right now. Dad's shop is full of crap, I live on top of a hill, not many safe places to get one up in the air properly. What is causing that sound?
View 5 Replies
I have a 2003 Ranger 4x4 with the 5speed automatic. It has 215,000 miles on it and I don't drive it regularly anymore. Lately, I've noticed that it will shake after start up for 10-30 seconds. This only happens after it has sit for a few days or a week. After it warms up, I can drive it and stop and start it again and it has works as usual.
Is there some way the convertor is leaking out fluid and it shakes until the convertor is full again? Or is something else the problem. I've changed the fluid two or three times during the life of the vehicle.
View 4 Replies
I am a new owner of my first truck and it is a 2003 Ford Ranger 3.0L Extended Edge with 138,000 miles on it. I keep getting a chirping noise coming from driver side of truck. It only happens when I have the AC on. I can turn AC to just air and the chirping stops. This only happens when I am driving. If I have my truck parked in drive with the hood up, I go and turn on AC full blast and I hear no chirping. I can see AC compressor turn on a few seconds after I start the truck and it is not cycling on or off every few seconds as some people I have asked told me it should do. AC air is ice cold so I should have enough freon. Now this chirping is not constant like a machine gun going off but just about every 5 seconds or so it would chirp. I have heard of bad camshaft sensors causing chirping but would that happen every few seconds and only when you are driving down the road with the AC on? Now I have noticed when truck has sat for a long time I get belt squeal for a few seconds and it then goes away. I think the squeal goes away when AC compressor starts because I observed this when looking for this random chirp. Any clues?
View 4 Replies
Got a 2002 Ranger XLT v6 auto w/80k on the clock. When I exit the truck and close the door with the key in the ignition the chime dings for about 10 seconds before stopping. Is there a way to shorten this? ( Other than removing the key.)
View 2 Replies
So it often just cranks for 15 seconds before it fires. I put the fuel pressure guage on it and you turn the key on but don't engage the starter it goes to 30 psi then back to 0 in a 2 second time frame. It then stays at zero. when you engage the starter pressure slowly goes up and it starts running while running its a consistent 60 psi.
I presume its the fuel regulator but why does it not go up to 60 psi and why does it just stop with the KOEO? Is it reasonable to just replace the regulator? or should I be replacing the fuel pump to at the same time? I will be doing this from under the truck since there is a lot of hard mounted equipment in the bed.
View 4 Replies
1990 Ranger 5 speed... The tranny has recently started making noises, first I thought it was the throw out bearing but I am afraid it is more than that. As I go thru the gears the trans makes rattling/grinding sounds: in 1st, 2nd, 3rd and 5th it is loud but 4th it is quiet. What might be going on inside the tranny....
View 14 Replies
I have a '92 Ranger with a 2.3 liter engine. She starts and runs a couple of seconds and shuts down. I'm thinking maybe a fuel pump is not putting out thepressure needed. Gotta go to work tomorrow and gotta get the truck running today.
View 2 Replies
I've got an issue with my 92 2.3 ranger.... sitting at idle for 30 or so seconds it starts to chug and sometimes dies.... I can hit the throttle and its fine for another 30 or so seconds.... while cruising on the freeway after about 30 minutes it starts to cut out badly... let out of throttle for a few seconds and it clears up and drives fine...
Here's the part that has me confused... pulled codes yesterday using a innova scan tool...
koeo were 4, 10, and 538...
koer were 111, 10, 157, 158, 181, 327, 328, and 334....
How does it give me a 111 pass code and then still come up with all the other codes? I am thinking my ecu may be screwed.....
View 4 Replies
'02 Ranger XLT, extended cab, 4X4, 4.0L SOHC, 5-speed manual, 114K miles.
Problem has occurred twice. After extended run time and engine fully heated, when I get home and shut it down, then attempt to restart within a short period of time, the engine starts very briefly, then begins shuddering violently and dies within a few seconds. Re-attempts to start result in a very shuddering attempt to run for a couple seconds, and then it dies. After a couple of re-attempts, it doesn't even attempt to start; just cranks over with no results. Has to sit about 7-8 hours before it will restart.
No OBD II codes; Passed, no codes shown. I purchased a crank position sensor, but haven't installed it yet: just a stab in the dark after hearing other people's experiences with other vehicles.
First occurrence followed a lengthy trip in heavy stop-and-go traffic. Shut it down when I got home, then attempted to re-start after a few minutes to run a short errand. Sat for two days without any re-attempts; then restarted and ran fine on first try a couple days later.
Second occurrence followed a couple hours of hitting yard sales with the neighbor, in which time I did not shut the truck down; just left it idling while we perused the sales, for fear it wouldn't re-start. Reckon it's a good thing I did, 'cause when we got home and I shut it down and attempted to leave again shortly thereafter, it malfunctioned as described.
Retries failed after sitting 4-5 hours, but after eleven hours of sitting, it started right up and ran normally.
View 3 Replies
I have a '97 Ranger with about 120k, 5 spd manual transmission, 2wd. For the last 2-3 months I'm hearing and feeling a clunking or rattling noise (I can't decide which it is) coming from the rear of the vehicle at random times.
I can't really predict or find a pattern of when the noise will happen, but it seems like it is most likely to happen when I'm either accelerating up a hill or when I'm braking relatively hard. It happens whether the clutch is in or out. Doesn't seem to matter. It does NOT happen when idling, only when traveling. I don't ever remember it happening at highway speed (65mph).
If I have my hand on the stick shift I can feel the shaking / rattling as it happens. There seems to be no impact on the performance of the vehicle - no additional trouble shifting into or out of gear, accelerating, or anything else.
On a recent trip I towed a 1,000 lb trailer and I did not feel or hear the noise at all during that trip (about an hour each way). Any guess as to whats going on?
View 5 Replies
I recently purchased a 1997 Ford Ranger with a blown 4.0 with a 5 speed , I have a 5.0 with a Carb and 5 speed out of a 80s mustang . Is it possible to use this in the 97 Ranger , I understand I need a different fuel pump but motor mount wise I was hoping it would fit.
View 2 Replies
Went to work one day and went to put my truck in park and it went as far as reverse. It has alot of play in the shifter. I have had a couple of people look at it and said that they would not touch it because of the air bag. I am not afraid to work on it myself if I just knew what to do. I am a single mom and on a budget, I would rather do it myself.
View 6 Replies
