I have a 1997 4.0L Ranger with an oil leak. It is near the front of the engine, I don't really see where it is. I was wondering if there is any common oil leaks near that general area?
View 4 RepliesChanged my oil today. Noticed oil coming off the front of the engine. Where this could be originating or do I need to take the belt cover off? I hate having a leak. Wanna get it to stop. Just need to know what I may be up against. 1996 2.3ltr.....
View 9 RepliesI saw a nice very clean 2011 ranger with 63,000 miles on it . But there looks like it has a oil leak on the upper right front of the motor. Behind the pulley that does not have any groves in it . It could be a gasket or a oil seal I don't know. Is this oil leak something common with the 2.3 engine?
View 4 RepliesI bought a 1990 ranger with only 38000 miles on it from a online auction from boing aircraft. it never left the flight line and never even had a title. I picked it up from the airport and found out that it didn't have AC like they said, I was a little ticked but that isn't the main problem. When I drive it and it gets warmed up it leaks Tranny fluid from the front of the transmission. The engine does not overheat. It is a 4 cyl AOD automatic with a real thin radiator and a transmission cooler. Without AC the truck isn't the good deal I thought I was getting, and with a bad tranny this is becoming a big OOPS. Why this is happening?
View 3 Replies2002 Ranger XLT, Super Cab, 4X4, 4.0L SOHC V-6, 5-speed manual transmission. Noticed burnt oil smell. Checking under truck revealed oil drips on garage floor from rear area of engine. Traced to rear corner of left valve cover, but can't see enough of the rear of the engine top-end to say for sure where it may be coming from.
Before I put the truck in the shop for repair, where the oil may potentially be coming from on this particular engine? (I checked; the valve cover fasteners are secure) Any "chronic" oil leak problems with this model engine, or anything?
I have a real problem with 2000 Ranger, after changing the upper radiator hose and thermostat, I now have a pretty constant leak from the gasket between the thermostat body and engine. Appears to be something that is triggered by the thermostat opening, so whatever the leak, the thermostat is blocking it.
I've changed the gasket, cleaned the mounting surface as good as I could. Tried re-torquing the bolts, but on that score - what is the torque specs for the 2000 3.0 liter Ranger?
But ultimately, what the heck is wrong here? This should be a pretty brainless operation really. Am I tightening the connection too much and cracking the gasket? I guess that has just occurred to me, although the gasket is not as stiff as a typical fiber gasket is.
I had a check engine light cane on. I took it for it to get checked and they gave me this code- P0457 EVAP small leak detected. ECM has detected a large leak in the EVAP System during a system monitor test.
The paper said I had a leak in the Evap canister or hose. I took the truck to a mechanic and was told I had Bad oxygen sensors. Can Bad/Dirty oxygen sensors make this error code come up?
Exactly where the oxygen sensors are? I was told they were behind the mufflers but I didn't see any and the diagram I found was not accurate.
2002 Ford Ranger XLT v6 extra cab.
I have a 97 Ranger 2.3 standard shift, No A/C, a pretty simple Ranger with 158,000 miles. About a month ago while do some checking around under the hood I noticed my coolant overflow tank was empty, so I filled it up to the proper level with some anti-freeze mixture. Thinking if the system was low on anti-freeze it would suck what it needed from the recovery tank, wrong! About two weeks ago I noticed that my temperature gauge was NOT registering in its normal position and was considerably lower towards the Cold mark. Heat coming out of the heater was normal.
I opened the radiator cap and everything looked okay. After a few days this would not go away and replaced the thermostat thinking the thermostat was stuck in the open position, wrong again! I burped the system by letting the engine run with the radiator cap off and filled the radiator with anti-freeze mixture every time some of the air was expelled. I did this for a few days and noticed that the engine would not reach normal operating temperature at idle speed! I had to put something on the gas pedal to increase idle speed so the engine would get hot, this is not normal. Finally I got to a point where the radiator would not take anymore anti-freeze mixture, but the problem still exists.
Two things I noticed that will get the engine temperature up to normal, engine speed (RPM's) and not having the heater on. Let me explain, at normal idle the engine will not reach its proper temperature, but when driving down the highway the temperature goes up to normal (about halfway on the scale) no matter if the heat is on or not. When stopped at a light or just idling I can watch the gauge slowly go down towards the cold mark, if I turn off the heater it takes longer to go down to cold. I do know the heater fan is cooling the coolant to a degree (no pun intended), but it shouldn't cool it so much as to make the temperature drop so dramatically. Okay, heater off, riding down the highway, everything normal, come to a stop and idle temperature starts falling slowly, but when I turn on the heater the temperature starts falling faster.
My diagnosis: I have no leaks of anti-freeze, checked and re-checked. I have no symptoms of a blown head gasket, no milky white appearance on dip stick indicating anti-freeze mixing with engine oil, no clouds of white smoke coming out of exhaust, checked tail pipe for anti-freeze, none found, no loss of power and no loss of gas mileage. I changed the thermostat, like I said. Do not think it could be the radiator pressure cap, normally if the cap goes bad the system will have no pressure and the engine will overheat, the opposite of the problem. Water pump, normally if the water pumps goes the coolant will not circulate through engine and will over heat, again, not the problem I am having. Could it be:
1. A long shot, I bought a defective thermostat and it is still staying open.
2. The temperature sending unit has gone bad, very improbable since it does register the correct temperature when truck is moving down the highway.
3. The coolant is spent, again unlikely, it has been in the engine only for about 3 years and still looks clean and green.
4. Have to have a cylinder pressure check to determine actually if the head gasket is really blown or not, which I doubt.
My conclusion is that I still have a huge air lock somewhere in the system and the engine is still not completely filled with coolant and when the rpm's drop not enough hot coolant is reaching the temperature gauge sending unit, but if that much coolant is not in the system, why am I still getting lots of heat blowing from the heater? The vehicles cooling system is not that complicated and there are few parts involved in its proper operation, I think I have covered them all, but somewhere I am missing something to pin point my problem.
I'm hearing a sort of faint rotating squeaking noise coming from the front of the engine; I can only assume that it's something with the belts. Nothing too pronounce cause I just notice it yesterday, anyway I was hoping I get another take on what this might be before I take it to the mechanic tomorrow.
View 12 RepliesOk, I have 1997 Ford Ranger, 4cyl, manual transmission, and more miles than I'd like to admit to.
Yesterday, I noticed that one of the vacuum lines was coming dangerously close to hitting the serpentine belt on the front of the engine. The clamp that normally holds the vacuum line in place rusted away a decade ago, so I decided to use some velcro ties to attach the line to the positive battery cable. I didn't twist or pull on the cable in any way and the vacuum line isn't applying any force to the cable.
I get in the truck a few hours later, hit the key and I get >click<, but nothing out of the starter. One click when the key is in the start position, nothing more (as opposed to click-click-click).
Not thinking about my repair earlier, I went down to Autozone and had them test the battery - 12.8V and 550CCA, no problem there.
So then, I thought well since the click is coming from the starter relay, maybe that's where the problem is. I read on another forum that sometimes the starter relay can be resurrected temporarily by hitting it with a hammer. Which I did. And it did work! Now the truck is starting up normally every time, but I'd like to replace whatever was bad.
My questions :
1. Did I prove anything by hitting the starter relay with a hammer and then starting the truck?
2. Should I still be looking at the battery cables?
3. Should I stop hitting random parts with a hammer and take this truck down to a real mechanic before I do serious damage?
My truck has had this annoying tendency to drink coolant. I believe I took care of it by replacing the thermostat gasket. Not so, it drinks about a quart every 50 miles - so quite a bit really.
Finally bit the bullet and took it to the dealer so that they could figure out where the coolant was going.
Answer I got back was - timing cover gasket, water pump, lower radiator hose.
The water pump appears to be good, its just the gasket that's bad. So my question is - how significant is the timing chain cover leak? Poking around online it appears to be reasonably common, but sounds very expensive. The dealer indicated it would be 2 days work minimum.
I bought a '98. At the front passenger side of the engine, the injector rail is leaking fuel (a fair stream of it). I have done some googling, and browsing around the forums, and can't find much in the way of specific info on where to start with this.
Whatever the device at the front of the rail - Without digging too far, it seems that the leak is coming just below it.
Questions:
Am I obliged to change injectors with the rail?
What is involved with changing the rail? Removing upper intake only? At all?
What is the box shaped device at the front of the rail, passenger side? Test port? Pressure Regulator? Both?
I won't have a chance to work on this again until next weekend, but thought I'd try to do some homework beforehand.
I have a 96 ranger with a 4.0 and an automatic transmission that has a horrible oil leak when cold. The leak looks to be coming out above and behind the oil filter. After running for a few minutes the oil leak appears to go away.
View 6 RepliesThe problem I have is the truck won't move in o/d. If I put it in revers 1,and 2 it works. A little back ground. 4 years ago the trans went out of my 95 4.0 4x4, had it rebuilt so it has 0 miles on it. It got really cold that winter had lots of trouble getting the trans and torque converter lined up. motor went bad on me. A few months ago finally had some money to spend bought a 98 explorer sport with a 4.0 x code motor. the motor runs fine apart from an oil leak and an exhaust leak. the exhaust leak is no big deal I just haven't gotten the system tight yet.
View 8 RepliesMy overflow tank seems to be going empty slowly. The last time I filled it was in March and I filled it to the Full line. Now, the overflow is almost empty. I did 425 KM last night almost non-stop and the level stayed the same since that night and today. So, I am not burning any thru the gaskets. Exhaust is not white neither.
I did see one suspect thought. I have this really small rad at the bottom of the bumper and it seems a little wet around the tubes that enter it. Could it be that? I have no spots on the driveway or road when I park. Specs of my truck:
190 000 KM.
Oil changed on Saturday.
Runs well, no loss of power.
Temps are good.
I was adding some fuel from a can to my Ranger last evening and I noticed gas was dripping on the ground. I traced it to, as best as I can tell, where the inlet pipe meets the tank.
Cannot see up there at all so not sure how it is attached. How I might be able to repair it without dropping the whole tank. Some kind of goop I can reach up there with and lather on to try and curb the leak?
I just had trans rebuilt in my 98 4x4 4.0 ranger I thought while they had the trans out go ahead and replace rear seal. Got the truck back leaking bad carried it back they claim to have replaced it twice while they had it and guaranteed it was not leaking they say the leak is from the oil pan so I'm gonna pull the motor this week. Question is: can make an offset rear seal I still believe this is the problem. Which oil pan gasket to use.
View 4 Replies2004 automatic 88,000 miles 2wd
When I bought the truck it had a very small oil leak that would drip out of the bell housing between the housing and the inspection pan. it would leave a quarter (25cents) sized stain on the ground and would only drip for 10 minutes or so after I shut it off. in 3000 miles it would be down 1/2 quart of oil...
Well 3 weeks ago I stopped and noticed a HUGE stain now. I checked the oil and was 1 quart low. I filled it then I drove 90 miles the final week before parking and was down another 1/2 quart...
I am figuring the rear main seal is gone. I did some research and it seems these are common to go in the 3.0? What seal is the best to get? should I get the seal right from the dealer? or I will run into the same problem and go with a after market? I also learned that the crank shafts can get a groove in them and it's good to put a new "speedy seal" where can I get one of those?
Also for some strange reason I take the tranny out and the rear main is good ( I seriously doubt it) is there anything else that could be leaking that I should check when I have the tranny out? Can I remove the tranny with the factory exhaust still in place? it looks like it can squeeze just by it?
My '96 ranger, 4.0, auto transmission has developed a coolant leak. It is at the rear of the engine, passenger side, at or just above the bell housing. I can't quite see where it is leaking from even using an inspection mirror from on top or underneath. The engine runs great. I just finished replacing the power steering pump, ac compressor, dryer and hoses. What is back there? Freeze plug? Do I fear the worst and that the head or block warped? I may drill a hole from the passenger compartment to try and get a better view.
View 4 RepliesI have a 98 Ranger 3.0 with a standard transmission. The truck has 240,500 miles so far. It runs just as good as the day I got it 11 years ago, doesn't use any oil and still gets 23 MPG. Last fall, it developed what sounds like an exhaust leak under the hood. It seems to be coming from the area of the EGR valve. The trouble is that I can't feel it or smell it. I have carefully felt the entire length of the tube running from the EGR to the exhaust manifold and cannot feel any leaks. There is no soot or any other evidence of an exhaust leak.
The noise isn't there for the first minute or so that the truck is running. I would think that if I had a cracked manifold or some other such leak, it would be worse when the engine is cold but this is not the case for me. It is most noticeable when pulling a hill as slow speeds in a higher gear. I have checked for codes (no CEL) and there are none. When I first heard it I figured that I would wait until it gets a little worse and I would be able to find it. Its been been over 8 months now it has remained the same.
My truck lost its exhaust a few months ago and it's on the back list of things for this truck so I've been running it without it. However, my neighbors do not like it so, I frequently shut the truck off and coast in down my driveway to park it when it's late. But anytime I do that, I will park the truck and notice a puddle of ATF(ps) on the ground and the PS pump goes empty. Nearly no loss for a weeks when I don't turn the wheel with the motor off.
View 2 Replies