Ford Ranger / B-Series :: 1997 2WD Went From Fine To No Start
May 26, 2012
My son's 97 2WD Ranger with 2.3L, 5 speed, no a/c, basic XLT standard cab.
I was using his truck because my 93 Ranger was getting a new starter on it. I drove to work with no problems, then after work, it started just fine and drove a few hundred feet to a stop sign where it promptly died. I was able to start it again with some effort and drove to the next stop sign maybe a quarter mile away. Truck died again, but this time it would not start. Towed it home about seven miles and its in the driveway now. The previous owner had new Motorcraft platinum plugs and wires installed, new fuel filter, fuel injectors cleaned, all about 11,000 miles ago. My son has had it for about 6,000 of those miles.
It felt like it ran out of gas, but the gauge showed about 1/4 tank, and I put about 3 gallons more from a gas can into the tank with no change in being able to start it.
Here's what I've checked so far according to my Haynes manual:
Turned key and listened for fuel pump and it seems to go on just fine.
Checked fuses and they are fine.
Swapped around relays in distribution box with no change
Checked resistance at coil pack and it was about 1.7.
Checked resistance at one injector and it was about 1.7.
Checked inertia switch and it did not need a re-set.
I don't have the ability to check fuel pressure.
View 14 Replies
Advertisement
My son's Ranger wouldn't start today, turns over fine, added gas to make sure it wasn't out still no hit.
Other than fuel pump (he said he couldn't hear it) what things should he check? I'll check back in the morning.
1994 Ranger 2.3 4 Speed ....
View 3 Replies
I have a 97 ranger with 3.0 it runs great but once you drive it and shut it off and go to restart it it will turn over but not start it used to start once I let pressure off the fuel rail, but now is a little harder to start when it does this but it looks as thou coolant comes out of the reservoir when this happens I think it might be coolant sensor or thermostat problem causing the timing to advance until it cools but then again why was it starting when I released pressure from the fuel rail and also I don't believe my check engine light works...
View 8 Replies
My friend's 1997 4 cyl ranger died and won't start. Cranks fine with no codes on OBD2. Was running fine before it died.
View 5 Replies
1997 2.3 Ranger w/ 160,000 mi. Every few months it won't start, sometimes after just having been running fine. Symptoms:
-the dash lights will be dim or off completely
-the chime will be softer than normal
-the headlights will not work, or be dim
-the starter will sometimes briefly click, sometimes crank once, sometimes do nothing
-the emergency flashers will sometimes click much faster than normal
-if during one of these "episodes" it does start, the battery light will sometimes flutter on and off, and the meter will flutter a little higher than normal. The next time I stop it, it typically will have the same problem.
-it will typically start if i get it jumped
My battery, starter, plugs and wires are all fairly new. On occasion, when it is having this problem, and I am trying like crazy to start it, if when I turn the headlights on and they are no longer dim, it starts right up and runs fine.
View 7 Replies
997 2.3 TruckSo this has been an issue for a long time, actually one of the issues I had when I got the truck 3 years ago. After it rains or is extremely humid, my truck does not want to start. Sometimes it will after cranking and cranking and cranking for a while (stopping to cool the starter of course) and other times it won't start.
This time around, it won't start. I cranked it for a little bit and had my dad check for spark while cranking. No spark at all. What should I start looking at? Coils, crank sensor and wires are all newer. As mentioned before, EEC has been replaced. Could it just be bad luck and I got a crap crank sensor? All fuses and grounds are good.
No codes, either except for the occasional misfire code that I get for some reason after pushing in the clutch to decelerate from a higher RPM. It'll fall and start to misfire, but clear up when taking back off.
View 1 Replies
I have a 1995 ranger with a 4.0 it cranks just fine wont fire has alot of fuel spark it will crank and crack then it stop and acts like it is going to fire up and stops cranking... This thing has 253k on it...
View 4 Replies
I'm having a bit of trouble with my fathers '03 Ranger Edge 4.0L. It has about 100k miles on it, and we keep it very well maintained. This is the first major problem we've had with it.
When the problem first occured, it had been driven about 30 miles on the highway and about 5 miles after getting off the highway, he pulled up to an intersection and stopped. As he started accelerating again, it all of a sudden started sputtering, surging (almost exactly as if it were running out of gas), and then stalled. It continues to exhibit this behavior. It will start and idle fine, but struggle and then stall when given any amount of throttle. It's also an automatic transmission if that makes any difference.
Fast forward to this past week after we had it towed home. We have checked the fuel pressure, and its dead on at about 64psi. We changed the fuel filter, changed the PCV valve, changed the upstream O2 sensor, put in a new air filter, cleaned the MAF sensor, and cleaned the intake of the throttle body. We're now at a loss as to what could be causing the problem. The CEL is not on, and there are no codes being shown when we plugged it in. We also thought it may have been bad gas, so we drained the tank and put fresh gas in from our preferred station. The plugs and wires are also fairly new, only about 4k miles on them.
Are we missing anything here? What else we could try? The absolute last resort is taking it to a shop, we're going through a rough patch with finances.
View 3 Replies
I have a 2006 2.3 ranger motor runs fine at idle and as I ride down the road the motor just cuts off. If I pump gas it will take off again and in 3 miles it will do it again. After 20 miles running good it will cut off again. Replaced coil pack, fuel pump, Cam sensor, Idle control sensor! What else could be causing this?
View 3 Replies
89 2.3l 4x4 will crank just fine but no start. It is getting plenty of fuel. Replaced ignition module,crank sensor,computer, checked all fuses. I've been looking for a broken wire with no luck. Doesn't seem to be getting any power to the coil packs. Truck was not driven very often until a month ago. Started up fine everyday until the no start.
View 10 Replies
85 2.0L Dura Ranger.
All of the Idle control wiring and box and sensors have been removed; all else is original. The truck ran just fine after the removal of the above paraphernalia (years). The truck simply quit, no spark at the coil, cranks just fine. All of the wiring has been checked for continuity. The Following components have been replaced with new:
Ignition switch.
Coil.
Dura-spark Box.
Dist coil.
Starter solenoid.
Rotor & Cap.
Plugs and wires.
Correct voltage is present at the coil & D-spark box side of the connector.
Coil tests close to what I think is correct for resistance and the engine ran with it.
I have tested both sides of every connector. I'm not sure what the output side of the D-Spark box (blue tab) voltages should be, and I am unable to test the trigger signal at the coil, however with no output and power in I'm guessing that is the problem...
View 14 Replies
I have a 93 Ford ranger that will not start. It was cranking fine. It would take 2 or 3 tries when it was cold but once warmed up it ran fine and would crank right back up until it was cold again. The last 3 or 4 times I drove the truck it fired right up on the 1st try. Then the last time I drove it, it cranked right up and I drove it between 5 and 10 miles. It sat for about an hour and when I tried to crank it, it wouldn't start. At first it sounded like it wanted to but after a few seconds all it would do is turn over.
After about a week of sitting I was able to crank it up again. It fired right up. I let it run for 15 minutes or so turning it off and re-cranking it. About 4 or 5 times. Then the last time I cut it off and tried to crank it back up it wouldn't start again. I replaced the pickup coil in the distributor, cleaned off the rotor button and leads on the distributor cap (they didn't look bad and were working fine before), I checked to see if I was getting spark but Im not getting it from the spark plug wires or directly from the coil wire.
I checked with a test light to see if I was getting power to the coil and distributor from the wiring harnesses. With the key on power is going into both but I'm not getting any arch when I test directly from the coil wire or the spark plug wires. Ive also switched out the relays and tested the coil and starter solenoid on another vehicle and they work fine. My next step I'm thinking about replacing the computer but don't want to spend on a part a can't return if thats not the problem.
View 13 Replies
I have a 2003 Ford Ranger 4X4 4L AUTO. About once every 6 months it will not start. It cranks just fine but doesn't fire. After about 45 min. it start and runs great for an other 6 Months. I have replace the plugs, wires, distributor cap but it hasn't solved the problem. It has had this problem when it is cold and warmed up.
View 4 Replies
So after work tonight I went to start truck it turned over fine but wouldn't start, when it finally did it barely ran and then it was fine, I had it b4 when I start it would turn over for a little bit b4 starting, would that be fuel pump?
View 1 Replies
The Engine cranks over fine, but won't start. When it does start everything is okay and it runs good with no codes. I noticed that by taking the key out of the ignition, I was checking under the hood, and put it back in the truck fired right up. Also it has never done this to the second driver who has a different key. The truck runs fine at all speeds and loads, even when hauling twenty bags of wet mulch. It's a 2001, 4.6 L, RWD. Could the PATS Chip be failing?
View 9 Replies
I recently purchased a 1997 Ford Ranger with a blown 4.0 with a 5 speed , I have a 5.0 with a Carb and 5 speed out of a 80s mustang . Is it possible to use this in the 97 Ranger , I understand I need a different fuel pump but motor mount wise I was hoping it would fit.
View 2 Replies
Went to work one day and went to put my truck in park and it went as far as reverse. It has alot of play in the shifter. I have had a couple of people look at it and said that they would not touch it because of the air bag. I am not afraid to work on it myself if I just knew what to do. I am a single mom and on a budget, I would rather do it myself.
View 6 Replies
97 automatic 4x4 SXT 4.0L. 4Hi will engage, but when I shift to neutral, press foot on brake, and shift to 4lo, nothing happens. No light, no sound. Occasionally it will make a sound, and even more rarely will light up, but it does not feel like 4Lo is engaged even when indication says it is. I pulled the shift motor and replaced, as well as verified that the transfer case could be shifted to 4 hi and lo by using an adjustable wrench. I have not put truck on stands yet, but I'm pretty sure 4 hi is truly engaging. I did attempt to engage with shift motor connected electrically but not mechanically, and it shifted. What is keeping 4 Lo from shifting? If it's a vacuum issue, wouldn't 4 hi not shift? I did check the vacuum lines and the vacuum reservoir and they seemed to be okay.
View 3 Replies
My girlfriend has a 2003 f150 4.6lt pick up its a great truck most of the time. Problem is when the temp gets in the neg double digits it becomes very hard to start it cranks fine but doesnt want to fire. When it does fire it might stall a few times before it stays running. The last cold snap we had I replaced the battery and in the summer the starter got changed. I have heard that this model of truck are known for hard cold starts. I am just wondering if this is true and any other thing besides block heater. It is strange that my 89 gm pickup will start no matter what temp and I'm having problems with the newer truck.
View 1 Replies
This 97 F150 4.2 is new to me, originally a very base 2wd white fleet vehicle, with 189,000 miles, runs smoothly and quietly, idles well, transmission shifts smoothly. Gets reasonable gas mileage.
Problem statement: the truck has an intermittent starting problem. The failure to start happens about 5-10% of the time. The motor will turn over fine, but but immediately stumbles while trying to start. Turn key off and then re-start attempt will be again followed by a bucking stumble. Some times the motor might try and run for 2-3 seconds bucking and stumbling. It is possible the problem happens more often when the truck is warm and has been shut off for 15 minutes or so. Once the problem happens it is very repeatable. It won't start again unless I wait about 30 minutes to an hour. Once it starts it seems to run very nicely. I have noticed some times when I go to successfully start the truck it might run roughly for the first 3-4 seconds bucking and sputtering a bit and then smooth out and not have an issue until the next re-start attempt.
The truck runs so nicely when it is running I doubt it is an issue with the plugs, air filter general tune up. Could it be an intermittent fuel pump issue? The next time it occurs I will check fuel pressure. Could it be fuel pressure regulator? Also tested by fuel pressure. ECU? The truck runs very nicely most of time that seems like a long shot. Crank sensor? Bad fuel? I did add some dry gas.
View 14 Replies
I have a 1997 Ford Ranger with a 4.0L 2WD. The check engine light just turned on with a code of p0133. I know that this is something with the bank 1 sensor 1. I tried doing some research and I think that it is on the passenger side before the cat converter. Now, I don't know what to do from there. How do I go about fixing this? What part do I need? How do I fix it?
View 1 Replies
