Ford Ranger / B-Series :: 1996 XLT - Radio Controls Don't Light Up
Dec 10, 2016
My 1996 Ranger Supercab XLT has the stock radio with 6-cd changer. The unit works fine but only the frequency/clock display lights up. I'm not sure where to start to fix it.
When a problem first occurred, the frequency/clock display flickered/dimmed randomly (and I think the other lights were fine). It was in the shop a few times for a fuel pump problem (the after market pump was actually not compatible and it took a bit to figure that out), and at some point after I got it back I noticed the display was fine but the remainder of lights didn't work.
I don't know if the shop did something or the failure behavior changed. What to look at? I can open the radio and fix that if needed (or replace it).
View 6 Replies
Advertisement
The warning light on the dash of my '96 ranger 4.0, auto with 233k miles started coming on. The only thing I have done recently was to replace my battery. Just trying to figure it out.
View 7 Replies
My 1996 Ranger runs ok but my check engine has come on. Using a scanner tool, indicates my cat monitor wont go to ready state and my error code is P0141. According to my research it indicates one of my 02 sensors. How to determine if its the one before or after the cat converter? About 6 months ago I had an exhaust leak repaired around my converter so I know I cant return it under warranty . If its the rear sensor , It looks fairly easy to replace but the front sensor looks a bit cramped.
View 6 Replies
I have a 99 Super Cab 4x4, 4.0, XLT. The radio has terrible static and the back lighting of the climate control goes off and comes on at different intervals. Are the two issues related?
View 1 Replies
My 96 ranger had lost a brake pad coming out of the mountains. I replaced the rotor but the ABS light came on as well as the check engine within a week. Several issues the clock spring was bad, replaced. The cam position Sensor was bad, replaced. I had this at a shop in a small town. While I was there they ran diagnostics.
At first the ABS module was sending data and gave them some info. Suddenly there was no more data stored in the module. They ordered a new ABS module installed it and replaced the LF sensor cable. Both sensors were cleaned prior to this.
The new abs module required a trip to ford to reprogram. At the shop they still could not get the light out. I took the truck home to my ford dealer and they said bad abs. Got a new (rebuilt Mfg discontinued) Installed and ford said this was bad with a code c1102. 4 w 4wd installed needs 4 w 2wd. ordered a new abs. Ford said same code again and the tech said that the ABS is not communicating through the obdii port.
My thoughts are the reader they used at the small shop was defective and either shorted out something or blew a fusible link. I am told this is 4 wheel abs with the rear sensors are on the pumpkin but after looking at the diagrams I do not see a RABS fuse. I have tested all fuses, and the shop replaced several relays. The pcm and ABS diodes check ok. Perplexed.
View 2 Replies
My engine has 2 ignition coils, and b went bad, but which one is b. ?
View 9 Replies
I have a 1996 Mazda B2300 & I heard that it is similar to the Ford Ranger.
Well the thing won't crank or start.
This is what I have done so far. I wanted to put a RPM meter on it. I followed YouTube videos on how to do it. I cut the Tan wire w. the yellow stripes & try to connect the wire to thr RPM meter. Then it won't start soo idk what to do. I also took put the PCM too. (I was looking for the wire) Now be honest, I talked to a mechanic, he said thag I might have blown my PCM or Blown another fuse. But when i put the key in to crank, it won't start ot click at all. The lights come on & it wants to start but won't start.
Then my mechanic tried to start it by the... Idk what it is called but you can start it & it wont evet start. It will crank like crazy but will not start at all.
View 1 Replies
I have a 96 Ranger 3.0 auto that is hitting 300,000 miles. I've got a 302 that i build for my F150 but know i'm thinking of transplating it in the Ranger. Is it a big deal in putting a SB in place of the V6.
View 4 Replies
I seen on this site awhile ago something about a fix for the heater control door, I have a 1996 Ranger and all I have is Hot heat and cannot cool it down with the temperature control.
View 2 Replies
I'm in the middle of replacing my pump. With the new pump are a plastic washer and a small rubber o-ring but no instruction where they are supposed to go. They didn't know at auto zone and I haven't heard them mentioned on any youtube video. I found a crushed torn up washer similar to the plastic one in my catch pan. Maybe it is supposed to go in around the high pressure hose connection.
View 6 Replies
I am working on a 96 ranger 2wd the front brakes were shot or nearly so,about 1/8 in left and cracked. Changed them this morning at 5am because that is the cool of the day (104 today) everything up front works fine but the howling and nails across the chalk board from the back was still there. Took it to my freindly les schwab and they told me it needed axle seals on one side and the noise is from the gear lube on the shoes. they wanted 800 bucks to fix everything, went and bought new shoes,new seals,gear oil,and gasket for rear end cover it is an easy half hour job. As I was driving home tonight from the parts store the noise stopped so now i am worried either it was a rock stuck between the drum and backing plate or something broke. everything sounds and works fine....
View 2 Replies
I have a 96 ranger with a 4.0 and an automatic transmission that has a horrible oil leak when cold. The leak looks to be coming out above and behind the oil filter. After running for a few minutes the oil leak appears to go away.
View 6 Replies
My ignition key is stuck / locked in the off position. The first time this happened I jiggled the key while moving the wheel back and forth and it turned. The next time in the truck nothing worked. I let it roll back a bit then tried, pushed the clutch in and put it in neutral, etc it did not move. (Just had the clutch and clutch hydraulics replaced.) The wheel is locked. The key removes from the cylinder.
I know it is easy to replace the Ignition Lock Cylinder when you can turn the key in the run position. How to remove it when locked in off?
View 4 Replies
Originally started with a p0302 code, and it cleared. CEL came back on with codes p1131 and P0401. First time with an 8 plug 4 cylinder. Truck has 263000 miles, and still original (metal) DPFE sensor. 1996 ranger 2.3L.....
View 1 Replies
I have been hauling a lot of garbage with my 96 ranger this last week. The differential has been making a little more than usual noise like growling, but it has always been smooth, now all of a sudden it shakes like a tire out of balance up to about 55 then it is like a switch is thrown and everything quiets down and the shaking goes away, until i get around 55. I haven't climbed under the truck yet just checked the tires and grabbed the drive line they are all ok,i don't see any leaks so it is a head scratcher. Hopefully it will be something easy, but it hardly ever is.
View 7 Replies
I have a 1996 Ford Ranger with 95k miles on it. Recently, my truck's automatic transmission has been slipping really bad. I'll be driving down my road and while going around a turn, the clutch feels like it randomly disengages, so when I press on the gas, it feels like I'm revving my truck in neutral, and then it will all of a sudden get back into gear, violently a lot of the time. However, once the truck is warmed up, the it runs perfectly and never slips. I've checked my oil multiple times and even changed the oil filter in the transmission. I am not sure if this has anything to do with it, but if I let my truck idle in park for a little bit, the RPMs will increase and if I shift in to reverse or drive while the RPMs are high, it'll do the same thing.
View 14 Replies
My son just purchased a 1996 Ford Ranger 2.3l 5 speed it is a nice little truck. But I have a question when you press in the clutch it acts like the choke has come on it idles way to high. When you come to a complete stop it is a few minutes before it goes back to its regular idle. Is it suppose to do that?
View 9 Replies
I have a 96 ford ranger 4cyl 5 spd. I've only had it for a month or so, but I've noticed on cold mornings my odometer won't work. The trip or the total mileage. I can hear the odometer cable clicking. Once the cab gets warmed up it'll start working. It's only happened twice, at about 50 degrees or lower, so I can only imagine what'll happen once winter kicks in. Where to go from here? I was thinking maybe it needs to be re-lubed or something...
View 9 Replies
My check engine light came on about a week ago and was unsure what the problem was. So I tested the codes and it said that the camshaft position sensor was bad. So I have tried finding this sensor but little to no luck. I was unsure if it was the 2 or 3 pin, but after looking at some pictures of the engine I'm thinking it is a 2 pin. I attached two pictures of what I think might be the sensor? But I am unsure. This was right next to the timing belt cover, which is where it said it was located. I have a 1996 Ford Ranger, 2.3L.
View 6 Replies
I have a 1996 ford ranger and i have no tail lights i have license plate lights, brake lights, Hazard and turn signals. But no running lights on the rear end. Where the grounds are for this circuit and if some one has a schematic for this ranger...
View 9 Replies
I've had my truck a few years now but for 2 it was basically parked. When I started trying to use it again I am having issues with the clutch now. When it is cold everything is fine, but on hot days or after I have been driving for a while It will lock the pedal up and will not let me dis-engage the clutch at all. Sometimes when it does eventually let the pedal down it will go to the floor and stay there for a few seconds until it slaps back up and engages slamming the truck into gear.
I have yet to try much. I'm not good at working on anything other than stereos in cars but I am willing to try. My thought is some water got into the system and is boiling in the lines but I am not sure. Places to start? I really need my truck going and the couple places I've taken it dont even want to try it seems like.
View 2 Replies
