Ford Ranger / B-Series :: 1996 XLT - Ignition Key Stuck In Off Position
Mar 17, 2014
My ignition key is stuck / locked in the off position. The first time this happened I jiggled the key while moving the wheel back and forth and it turned. The next time in the truck nothing worked. I let it roll back a bit then tried, pushed the clutch in and put it in neutral, etc it did not move. (Just had the clutch and clutch hydraulics replaced.) The wheel is locked. The key removes from the cylinder.
I know it is easy to replace the Ignition Lock Cylinder when you can turn the key in the run position. How to remove it when locked in off?
View 4 Replies
Advertisement
Took my 96 B2300 2WD SE (190k) to lunch. When I went to start it back up afterwards, the key turned but no starter engaged. All the dash lights came on, and now stay on. With the key in, I can turn the ignition freely...no clicking to different positions.
It springs a little when I turn it all the way, but still no starter. When I remove the key, the dash lights stay on, etc. So, since it was on, we were able to push-start it. I've parked it on a hill for now, and will disconnect the battery when I get it home.
View 6 Replies
My check engine light came on about a week ago and was unsure what the problem was. So I tested the codes and it said that the camshaft position sensor was bad. So I have tried finding this sensor but little to no luck. I was unsure if it was the 2 or 3 pin, but after looking at some pictures of the engine I'm thinking it is a 2 pin. I attached two pictures of what I think might be the sensor? But I am unsure. This was right next to the timing belt cover, which is where it said it was located. I have a 1996 Ford Ranger, 2.3L.
View 6 Replies
My engine has 2 ignition coils, and b went bad, but which one is b. ?
View 9 Replies
My keys got stolen from my ignition (battery had died because key was left in ACC and I assume the attempted car jack ended in a key theft for some reason.)
The Ranger is 96, tilt steering with plastic shrouding and column shift A/T... I followed the procedure recommended for exchanging the cylinder without the keys:
-drilled retaining pin
-drilled key slot
-manually removed parts with needle nose
-cleaned, greased and went to reinstall.....
I discovered the small metal washer between the green plastic washer and the gear was broken in half because I nicked it with the end of the drill bit. I inspected this and from what I can tell it looks like the green plastic washer is designed to hold onto the metal washer, the two of them together, from what I gather are designed to keep the gear from moving sideways or tilting. I figured that the washer should do it's job even in two pieces if I could get it in there straight and get the green washer to grab it.
Anyway I stuck it all back in there, slid the new lock cylinder in in run position, and nothing good happened. It's in the whole way, I can see the retaining pin centered in the whole from underneath, but when I try to seat the retaining pin it won't budge. I tried to align the parts at a million different angles and I just have no luck. I am planning on replacing the little metal washer, but I don't feel like it being broken alone is enough to keep all parts from functioning properly. I am stumped because I did the procedure step for step and there is nothing else apparently broken or damaged. The only other factor is that the steering wheel is locked and that sometimes made the other cylinder hard to turn, but it freed up usually with a little wiggling, this cylinder won't budge.
View 1 Replies
My fuel gauge is stuck at the full mark. What to check and where to start?
View 7 Replies
None of my 4 keys will operate my ignition switch.
It's stuck in off position. Steering wheel is not locked and I have pulled pretty hard on it to see if I could get the ignition switch to turn.
I have a new switch on the way but I have to get the old one out and don't know how to get old one out if I cannot turn the switch to on position.
View 14 Replies
I have a 1996 Ford Ranger which was manufactured in 08/95. The key will crank the trunk fine, but it when put into the off position nothing happens. It continues to run as normal. You can even take the key out, but the truck runs like normal. Could this be bad ignition switch? The key seems to be doing its job because I can see the plastic pin(? I am not sure what its called) move back and forth down steering column when the key is turned.
View 7 Replies
I have a 2001 Santa Fe, and the key is stuck in the ignition. I can't even get it to turn to the Lock position, so it's stuck in accessories. Since I haven't had the funds to do so, I haven't gotten it checked out yet, and it's started to drain my battery. I have to jump it every single morning, so I'm wondering if there's anything I can do until I can gather up the money to fix it.
I have tried moving the steering wheel and shifting it all over the place and spraying DW-40 in there and a whole bunch of other things I've seen work for people on a bunch of different forums, but nothing works. I don't know if this matters, but before it got stuck, it would sometimes be hard to pull out or push the key into the ignition.
View 4 Replies
My 96 F-350 Crew Cab driver rear door lock is stuck in the locked position. I don't have a cause but do now notice that the pass door lock will not operate with the lock/unlock switch. The rear solenoids seem dead. Front door locks are working.
I tried to put a 10-32 coupling nut on the lock riser and pull. The down position is now 1/8-1/4" higher than normal. This thing is really stuck and is really bad.
So before I start pulling the rear seat and trying to remove the door panel from a closed door; how I might unlock this door? It would be a lot easier to get the panel off if it is open.
View 2 Replies
The key will not turn to off, stuck in acc. I have no power to the windows, sunroof, seat and seat heaters, and no brake lights, and the mirrors have no power either. I took the car to the local GM dealer who told me the ignition was not in any recall and found that the Body Control Module was bad and needed replacement.
View 5 Replies
I have a 97 Bravada. Recently the check engine light came on and then went off. I didn't think anything of it at the time till the other day I drove it to work and back fine without any issues, then the next morning I tried starting it and nothing happened. No cranking, no interior lights, no sounds.
I tried jumping it thinking the battery was dead but that didn't work. Now my key is stuck in the ignition in the accessory position. It will not turn all the way back to release the key.
View 11 Replies
Quite awhile ago my key started to randomly get stuck in the middle ignition position but it was happening very rarely and some gentle jiggling was letting me take it out easily. Well a few days ago that went from very rarely to each and every time I start the car.
Now its a tossup whenever I go somewhere whether the key will pop out like it should or I'll have to fiddle with it for anywhere up to ten minutes.
The car never has a problem starting, its only when I have arrived somewhere and need to take the key out that is an issue. I've managed to remove it every time so far but it has taken a fair amount of WD-40, jiggling the bejeezus out of the key and steering wheel and plenty of patience.
View 2 Replies
I have a 2003 2.4L 5 speed manual Santa Fe. I was parking my vehicle and removed my key as usual and realized that the car was still running. I put it into reverse rolled back and back into 1st to roll forward just to make sure I wasn't dreaming. I ended up pulling the fuel pump fuse and disconnecting the battery to turn it off.
When I replaced the fuse and reconnected the battery I was able to bump start the vehicle without the key in the car and drive it all the way home with no problem. I took apart all the plastic pieces around the Ignition and attempted to remove the cylinder but was unable to locate any sort of small button or pin to push on to remove it. Where is the release button?
What are my options here? Do I replace the cylinder first or get a new key, or is there something else that I should check first before I take it in.
View 1 Replies
I have a European Phaeton 3.2 litre V6 (gasoline) from 2003 that is giving me some problems. When I am finished driving I put the gear lever to parking position and turn off the ignition. I then get a message "Move selector lever to position p" and the key is stuck in the ignition.
So far, I have been able to get the error message away (and with that also been able to get the key out) by starting the car and move the gear lever around. Some times I have managed by only starting the system (by not holding my foot on the brake pedal). But tonight I couldn't get it fixed after numerous tries. I then simply waited in the car, because I didn't really know what to do, and after maybe five minutes the system shut down (energy saving mode?) and I could finally get the key out.
When I tried google the error message I found some topics about it on the Touareg forums, but they got the error message while driving and it had to do with the keyless system (which my car doesn't have).
What might be causing this problem? My local VW dealer is not very used to Phaetons (I am the only on in my town with one).
View 9 Replies
It's a 2001 Chevy cavalier. The key is stuck and won't turn the car off. Already have tried shaking the wheel and wd-40. The wipers won't work and the gauges won't turn on until I jiggle the key.
View 4 Replies
I easily removed the key lock cylinder but when I went to put the new one in I cannot get it to turn all the way back to lock the pin in place. The steering wheel is not in the locked position nor can I get it to lock. I have turned the steering wheel as far left and right as I could go with no success on getting it to lock or on getting the ignition key lock cylinder to turn back securing the actuator pin. The old key lock cylinder won't go back in either. What am I doing wrong?
View 3 Replies
I've recently purchased an 02 Envoy from an auction. There are a couple of issues. The main one started last night. While at the store I put the truck in park and turn off the ignition. The ignition will not go into the lock position. I messed with the key and go it to turn off. Then started the truck to leave and couldn't put the truck in gear. I messed with the shifter and was able to put into gear.
At that point the gear shifter would move from park to reverse without me pushing the break pedal. I drove home and could not turn the key all of the way off again. Moved gear selector from 1st to Park a few times and then was able to remove the key. I restarted the truck and could not move the gear selector again; however I was able to remove the key easily.
I am leaning towards replacing the "Neutral Safety Switch" on the tranny but with my symptoms, I've seen brake light switch, ignition, and solenoid at gear shift selection.
Back up lights do not work either. Since I purchased the truck, I've replaced,
-Battery
-Ignition Coil
View 9 Replies
My 2004 Accent is stuck in the "lock" position in the ignition, and the wheel is locked and barely turns in either direction. I know this is supposed to be an anti-theft feature and I've tried all of the solutions listed here...
Turning the wheel hard and soft in either direction while holding the brake all the way down and trying to turn the key. Putting the car in neutral and then park and trying the above Disconnecting the battery for a few minutes and trying the above Jacking the car up on one side to release the tension on the pin.
My question is can I remove the spring at the bottom of the locking pin by drilling a hole in the center of the plate? I've seen a few youtube videos of this done on BMW's. It will cost me $500 minimum to replace the ignition or steering column based on quotes I got.
View 10 Replies
My '96 ranger with a 4.0 auto will be running fine and then dies. When you go to start, the engine will will crank over. Also notice that there are no lights coming on the dash when the key is in the run position. A few hours latter the truck started right up. Not reading any codes. Transmission was rebuilt a few weeks before this problem.
View 6 Replies
Car: 1996 Nissan Maxima
The car has an automatic antenna (up/down when you turn on/off the radio). I wanted to disconnect the motor to leave it in the up position. I followed the cables to the antenna (left the coax alone, of course), and cut the 3 conductors that were leading to "a box" under the antenna. NOTE: This area in behind a metal panel.
As intended, the antenna is stuck in the up position. The problem is that I also lost the dash clock, the remote to the door locks stopped working, and the radio memory buttons do not work anymore (the radio comes on in AM every time).
AND here is the mystery; I went back to the cables, spliced them together (correctly - they are color coded) but NOTHING CAME BACK TO NORMAL. The radio is still messed up, remote still not working, and the dash clock is still off.
View 7 Replies
