Ford Ranger / B-Series :: 1996 - Start If Turn The Key To On And Jumping The Solenoid
Aug 27, 2014
I have a 1996 Ford Ranger XLT Automatic with a 4.0... A few months ago I went to start it and it would not start. All the lights were on and working, the radio worked etc. I figured it was the fender solenoid so I replaced it. Didn't fix it. I jumped the solenoid and it spun up. The only way I can start the truck is by turning the key to on, and jumping the solenoid. I replaced the ignition switch that is under the instrument panel, and the ignition cylinder that the key goes in to. I have reason to think that it may be the neutral safety switch, but I do not want to go out and buy the part and it not be the issue.
View 14 Replies
Advertisement
I have to fix the truck. Battery is pretty new, replaced solenoid next to battery this morning. Truck still won't start, just clicking away. Decided I needed to replace the starter, put the truck on jacks and went to the starter. At the starter solenoid there is a red cable attached, and a "loose" red wire, with a connector on the end. It would appear the connector just needs to be reconnected to the solenoid. But it won't "connect". Am I missing something? Should it not connect to the prong on the solenoid? Should I just replace the starter, and forget about the wire? I do have Chiltons for our truck, but it doesn't show a picture of the prong on the starter solenoid.
View 11 Replies
I have a 1996 Mazda B2300 & I heard that it is similar to the Ford Ranger.
Well the thing won't crank or start.
This is what I have done so far. I wanted to put a RPM meter on it. I followed YouTube videos on how to do it. I cut the Tan wire w. the yellow stripes & try to connect the wire to thr RPM meter. Then it won't start soo idk what to do. I also took put the PCM too. (I was looking for the wire) Now be honest, I talked to a mechanic, he said thag I might have blown my PCM or Blown another fuse. But when i put the key in to crank, it won't start ot click at all. The lights come on & it wants to start but won't start.
Then my mechanic tried to start it by the... Idk what it is called but you can start it & it wont evet start. It will crank like crazy but will not start at all.
View 1 Replies
i have a 96 ranger with a 2.3l engine sometimes it will start right up and sometimes it has to crank 4 or 5 times to start i just gave it a tuneup and changed the oil and filter. should i run sea foam through the oil system,it sat for about seven years and i need to convert the idiot gauge to a real gauge.
View 2 Replies
I just received this ranger and have never heard an engine sound like this before.
[URL]....
View 14 Replies
So I just finished redoing my head gasket. Everything is hooked back up the way it was prior to the tear down. I'm getting spark, fuel, compression, timing was set correctly according to Haynes, turns over but just doesn't want to fully start up.
View 3 Replies
I have a ford ranger 1996 4 cylinder. The truck was driving fine then all of the sudden it shut off and wouldn't start... I checked spark and that is fine also changed fuel pump and made no difference. We also sprayed lighter fluid and that did nothing. It sounds like it wants to start but wont.
View 10 Replies
So... p1451. Vent solenoid. I pulled the part and put 12v to it. Opens/closes just fine. Checked resistance on part, 55ohms like it should. Pulled vent canister, no apparent leaks or blockages. I traced wires back to cab. Cannot locate anybroken wiring. I looked up the pinpoint test on this dct and all thats left to test out is the pcm itself. Before I buy the obd2 scanner with all modes I wondering if I am missing something.
I did find a broken ground wire in my searching. Frame to body. My thoughts on a bad ground are that that would cause more than one monitor to register one fault code.
View 14 Replies
Well it all started when I was having starter issues my starter died and my solenoid was just clicking and after time there was no power at all to anything in the truck i have replaced the solenoid and starter and check battery and cleaned post and terminals. I am going to replace my negative cable as it was pretty bad but if this still does not work, so what to look for. The truck is an 87 ford ranger 4x4 5 speed with a 2.9....
View 9 Replies
I have a 97 ranger with 3.0 it runs great but once you drive it and shut it off and go to restart it it will turn over but not start it used to start once I let pressure off the fuel rail, but now is a little harder to start when it does this but it looks as thou coolant comes out of the reservoir when this happens I think it might be coolant sensor or thermostat problem causing the timing to advance until it cools but then again why was it starting when I released pressure from the fuel rail and also I don't believe my check engine light works...
View 8 Replies
My buddy bought this 2000 Ranger 4x4 with the 3.0 and 150,000 miles for 500 bucks. After he bought it, the number 2 spark plug boot caught on fire, and turned completely to ash. So we parked the damn thing, and have been training ever since, but it did run when we parked it. We replaced all plugs, wires suspecting a bad plug (and they were all fouled). Went to start it and now its on the verge of starting, but can't quite get there. So here's what we've done since.
-Replaced coil (had it tested, failed primary test on terminal 1, and secondary on 3 and 4)
No change
-Checked Spark by grounding spark plug
Good
-Checked Fuel at rail
Good- Held until empty, primed Fuel system (key on for 3 seconds 5 times) checked again, good)
-Truck had been sitting for three months, so put in small bottle of stabil and added 5 gallons with Lucas. Primed the system about 20 times, and tried to start. No effect.
-Checked battery.
1 bad cell, 3 low on water- replaced battery. Allowed it to crank for longer (before we were jumping it) but still didn't want to.
Note of concern : After we replaced the battery and went to start it, when the key was disengaged I noticed a hissing sound coming from the radiator cap. The truck is in Upstate new york and hasn't been ran in 3 months. I'm hoping its not but thinking it is a cracked jacket or a blown head gasket.
View 8 Replies
A buddy of mine has a 2003 Ford Ranger Edge V6 3.0L, he got the code P1450 the other day and asked me to look at it. Got all the info on what it could be but where ex actually is the EVAP canister and CV solenoid located? And what is the problem?
View 1 Replies
2007 Ranger XLT 2.3, 55k miles
Went to start truck today and got very little response.
Symptoms:
Workee:
Dome light (regular brightness)
key in/door open chime
No workee:
Dash lights
Solenoid (no response)
Headlights
Radio
Turn signals
Hazard lights
VOM tested battery- 12.82 V
Cleaned battery terminals
Every key turn there is a brief low chatter from interior fuse box.
Occasionally dash lights will flash briefly on key turn.
Occasionally PATS dash light will flash in 2 second cycle.
I'm suspecting the ignition switch but the no headlight condition puzzles me.
View 8 Replies
2001 Ranger 3L v6 auto, 186k miles. Never had a problem. One day last month I park it at home. 10 minutes later I need to make a quick trip . Get in, turn key, absolutely nothing happens. Replaced the battery, starter/solenoid, and ignition switch (not the key cylinder lock, but the white box inside the dash below and to the left of the steering wheel...has lots of wires going into and out of it,...turning the key slides a little metal pin inside it up and down). All fuses and relays are good, neutral safety switch is good. Key lock cylinder is mechanically working properly. Engine is not headlights, interior lights, wipers, radio, etc all work fine. Theft light is not blinking rapidly. Headlights do not dim when ignition key is turned. Where do I go from here?
View 2 Replies
My 1999 4.0L v6 Ranger (auto trans) is having some issues. Recently the fuel pump won't turn on as normal when I turn my key. I have to turn the ignition on and off 10-20 times before I hear the pump kick on and I can start it. I already checked the relay and fuel pump shut-off switch. Neither was the bad.
View 10 Replies
1998 Ranger, 3.0 liter manual transmission. The vehicle recently has had the engine replaced. Still a 3.0 Liter, but possibly is from a 1995 or 1996 Ranger. Replacement motor from a wrecking yard, appears to have been sitting for quite some time prior to purchasing. I had a friend change the motor out after getting the vehicle a few weeks ago.
Ranger drove fine for a week, but this morning it wouldn't start. One click is all it would give when you turned the key. Thinking the culprit was the all in one starter/solenoid, I replaced it with a new one this morning. Now the solenoid will click continuously when the key is turned, starter still will not rotate then engine.
Battery tests good - 12.4 volts; connections appeared fairly corroded.
Here is what I have done:
- Clipped off the first half inch of corroded terminal leads, replaced both sides with new battery connectors and wire brushed connections off at battery and starter.
- Replaced Starter
- With "S" connector disconnected, attempted to bypass starter connections and short terminals to see if a faulty clutch position sensor was to blame; shorting did not produce anything other than turning the key did.
- Paralleled an additional cable from battery to starter terminal to see if corroded wire connections were to blame; still just clicked repeatedly when attempting to start.
Crankshaft does rotate manually, does not appear to be seized up. Unsure of what else to check for. Not confident in friend's engine installation abilities, he may have screwed up something I'm not thinking of. On the other hand, I don't believe I would have been capable of swapping out the motor myself.
View 3 Replies
The truck just won't turn over makes a rrrgh rrrgh noice like it wants to start, I push the gas peddle to the floor and I should smell a lot of gas but don't!!! I added oil when it died at the store last night and it started up but the oil stick indicates oil is fine??? Pulled the diode out this morning put it back in the truck would not start just made that noise but turned it off and reseated the diode and it started??? These things may or may not have anything to do with the problem. Could it be electrical or oil pressure gauge sticking or something else that I could tell my mechanic and he could fix so I don't get stuck????
View 14 Replies
This has happened 4 times now over 2 weeks. The engine will turn over but will not start till I press the gas pedal. I have to keep the engine running for a few seconds by hold the gas pedal steady.After it's running you can cut the engine off and it will start right back up.
View 9 Replies
My 96 ranger had lost a brake pad coming out of the mountains. I replaced the rotor but the ABS light came on as well as the check engine within a week. Several issues the clock spring was bad, replaced. The cam position Sensor was bad, replaced. I had this at a shop in a small town. While I was there they ran diagnostics.
At first the ABS module was sending data and gave them some info. Suddenly there was no more data stored in the module. They ordered a new ABS module installed it and replaced the LF sensor cable. Both sensors were cleaned prior to this.
The new abs module required a trip to ford to reprogram. At the shop they still could not get the light out. I took the truck home to my ford dealer and they said bad abs. Got a new (rebuilt Mfg discontinued) Installed and ford said this was bad with a code c1102. 4 w 4wd installed needs 4 w 2wd. ordered a new abs. Ford said same code again and the tech said that the ABS is not communicating through the obdii port.
My thoughts are the reader they used at the small shop was defective and either shorted out something or blew a fusible link. I am told this is 4 wheel abs with the rear sensors are on the pumpkin but after looking at the diagrams I do not see a RABS fuse. I have tested all fuses, and the shop replaced several relays. The pcm and ABS diodes check ok. Perplexed.
View 2 Replies
My engine has 2 ignition coils, and b went bad, but which one is b. ?
View 9 Replies
I have a 96 Ranger 3.0 auto that is hitting 300,000 miles. I've got a 302 that i build for my F150 but know i'm thinking of transplating it in the Ranger. Is it a big deal in putting a SB in place of the V6.
View 4 Replies
