I have a 96 ranger with a 4.0 and an automatic transmission that has a horrible oil leak when cold. The leak looks to be coming out above and behind the oil filter. After running for a few minutes the oil leak appears to go away.
View 6 RepliesChanged my oil today. Noticed oil coming off the front of the engine. Where this could be originating or do I need to take the belt cover off? I hate having a leak. Wanna get it to stop. Just need to know what I may be up against. 1996 2.3ltr.....
View 9 RepliesI was adding some fuel from a can to my Ranger last evening and I noticed gas was dripping on the ground. I traced it to, as best as I can tell, where the inlet pipe meets the tank.
Cannot see up there at all so not sure how it is attached. How I might be able to repair it without dropping the whole tank. Some kind of goop I can reach up there with and lather on to try and curb the leak?
My '96 ranger, 4.0, auto transmission has developed a coolant leak. It is at the rear of the engine, passenger side, at or just above the bell housing. I can't quite see where it is leaking from even using an inspection mirror from on top or underneath. The engine runs great. I just finished replacing the power steering pump, ac compressor, dryer and hoses. What is back there? Freeze plug? Do I fear the worst and that the head or block warped? I may drill a hole from the passenger compartment to try and get a better view.
View 4 RepliesMy 2002 2.8 diesel ranger has recently been serviced replacing the turbo and a complete overhaul on the engine performed. I road tested it and it runs smooth... However, I am hearing a popping sound coming from the intake air filter. I was told it is because of the new turbo installed.
View 2 RepliesI have the problem that my 1996 ranger 4x4 has a break problem. When it comes to a stop it feels like one of the tires locks up, feel wired. Ihad the problem before i changed the front breakpads and it still continues. Air in the lines? ABS module?
View 6 RepliesThe warning light on the dash of my '96 ranger 4.0, auto with 233k miles started coming on. The only thing I have done recently was to replace my battery. Just trying to figure it out.
View 7 RepliesI noticed green coolant leaking from bottom of black, what I think is called, timing belt cover. There is 188, 000 miles, and when I changed the timing belt, I did not change the water pump, although I did change out the thermostat. I have done a lot of work on this truck in the past. I checked the oil and no signs of water or coolant mixed in. The water pump is not weeping from the top well. I rely on this truck and the way I look at it is I may just keep driving it until it goes kaput (its real beat up). Should I go to an auto parts store and see if I can buy some sealant. I would guess it is either the water pump or maybe the timing cover gasket? I have inspected all hoses, and I see nothing. The leak must be coming from somewhere under that black, plastic cover. I am capable and willing to do just about anything other than perhaps a full engine pull, although I have the wherewithal to do that too if absolutely necessary.
View 9 RepliesI have a 93 Ranger xlt and after checking wheel cylinders and calipers first I have found a leak that is coming from the brake line or maybe the RABS module. The leak is up along the inside of the frame and I can't get in there because of the gas tank. Has to change line or RABS in that area and am I correct in thinking the gas tank has to come out to do anything in there.
Also, in the manual it says to plug the line as soon as you remove it(at wheel cylinders etc) so the fluid does not leak out of the RABS because it can't be bled without an expensive piece of equipment. I am pretty sure it probably emptied due to the leak location.
I know where the filter is, i know how to bleed off the pressure. Im wondering if those clips are easy to slide off to remove the filter from the lines?
View 7 RepliesWhere is is my fuel filter and what are the steps to changing it. I have a 2002 Ford Ranger. Also how do you change the flashers, the left blink is really fast but the right blink is fine.
View 14 RepliesWhere the cabin air filter is located on my 97 Ranger. I purchased the truck used one year ago and would like to check or change if necessary.
View 2 RepliesThe other day I was driving down the road on a long, flat section and all of a sudden my truck started missing out of the blue. Ever since it started missing it hasn't stopped. The truck is an '89 Ranger, 2.3l, 5 spd. The plugs and wires were replaced last year along with the timing belt and fuel pump. It has been running great since then until now. I thought maybe it might be a clogged fuel filter so I replaced that but it didn't work. Also, it doesn't miss all the time. It doesn't miss when its idling or if you are going down the road while it is missing and slowly release the gas pedal it reaches a point while you are letting the pedal up where it will even out. It definitely seems like it is an "under load missing" scenario. Also, the Check Engine Light is not on. Where should I start looking?
View 4 RepliesMy 96 ranger had lost a brake pad coming out of the mountains. I replaced the rotor but the ABS light came on as well as the check engine within a week. Several issues the clock spring was bad, replaced. The cam position Sensor was bad, replaced. I had this at a shop in a small town. While I was there they ran diagnostics.
At first the ABS module was sending data and gave them some info. Suddenly there was no more data stored in the module. They ordered a new ABS module installed it and replaced the LF sensor cable. Both sensors were cleaned prior to this.
The new abs module required a trip to ford to reprogram. At the shop they still could not get the light out. I took the truck home to my ford dealer and they said bad abs. Got a new (rebuilt Mfg discontinued) Installed and ford said this was bad with a code c1102. 4 w 4wd installed needs 4 w 2wd. ordered a new abs. Ford said same code again and the tech said that the ABS is not communicating through the obdii port.
My thoughts are the reader they used at the small shop was defective and either shorted out something or blew a fusible link. I am told this is 4 wheel abs with the rear sensors are on the pumpkin but after looking at the diagrams I do not see a RABS fuse. I have tested all fuses, and the shop replaced several relays. The pcm and ABS diodes check ok. Perplexed.
My engine has 2 ignition coils, and b went bad, but which one is b. ?
View 9 RepliesI have a 1996 Mazda B2300 & I heard that it is similar to the Ford Ranger.
Well the thing won't crank or start.
This is what I have done so far. I wanted to put a RPM meter on it. I followed YouTube videos on how to do it. I cut the Tan wire w. the yellow stripes & try to connect the wire to thr RPM meter. Then it won't start soo idk what to do. I also took put the PCM too. (I was looking for the wire) Now be honest, I talked to a mechanic, he said thag I might have blown my PCM or Blown another fuse. But when i put the key in to crank, it won't start ot click at all. The lights come on & it wants to start but won't start.
Then my mechanic tried to start it by the... Idk what it is called but you can start it & it wont evet start. It will crank like crazy but will not start at all.
I have a 96 Ranger 3.0 auto that is hitting 300,000 miles. I've got a 302 that i build for my F150 but know i'm thinking of transplating it in the Ranger. Is it a big deal in putting a SB in place of the V6.
View 4 RepliesI seen on this site awhile ago something about a fix for the heater control door, I have a 1996 Ranger and all I have is Hot heat and cannot cool it down with the temperature control.
View 2 RepliesI'm in the middle of replacing my pump. With the new pump are a plastic washer and a small rubber o-ring but no instruction where they are supposed to go. They didn't know at auto zone and I haven't heard them mentioned on any youtube video. I found a crushed torn up washer similar to the plastic one in my catch pan. Maybe it is supposed to go in around the high pressure hose connection.
View 6 RepliesI am working on a 96 ranger 2wd the front brakes were shot or nearly so,about 1/8 in left and cracked. Changed them this morning at 5am because that is the cool of the day (104 today) everything up front works fine but the howling and nails across the chalk board from the back was still there. Took it to my freindly les schwab and they told me it needed axle seals on one side and the noise is from the gear lube on the shoes. they wanted 800 bucks to fix everything, went and bought new shoes,new seals,gear oil,and gasket for rear end cover it is an easy half hour job. As I was driving home tonight from the parts store the noise stopped so now i am worried either it was a rock stuck between the drum and backing plate or something broke. everything sounds and works fine....
View 2 RepliesMy ignition key is stuck / locked in the off position. The first time this happened I jiggled the key while moving the wheel back and forth and it turned. The next time in the truck nothing worked. I let it roll back a bit then tried, pushed the clutch in and put it in neutral, etc it did not move. (Just had the clutch and clutch hydraulics replaced.) The wheel is locked. The key removes from the cylinder.
I know it is easy to replace the Ignition Lock Cylinder when you can turn the key in the run position. How to remove it when locked in off?