I was adding some fuel from a can to my Ranger last evening and I noticed gas was dripping on the ground. I traced it to, as best as I can tell, where the inlet pipe meets the tank.
Cannot see up there at all so not sure how it is attached. How I might be able to repair it without dropping the whole tank. Some kind of goop I can reach up there with and lather on to try and curb the leak?
I have a 96 ranger with a 4.0 and an automatic transmission that has a horrible oil leak when cold. The leak looks to be coming out above and behind the oil filter. After running for a few minutes the oil leak appears to go away.
View 6 RepliesChanged my oil today. Noticed oil coming off the front of the engine. Where this could be originating or do I need to take the belt cover off? I hate having a leak. Wanna get it to stop. Just need to know what I may be up against. 1996 2.3ltr.....
View 9 RepliesMy '96 ranger, 4.0, auto transmission has developed a coolant leak. It is at the rear of the engine, passenger side, at or just above the bell housing. I can't quite see where it is leaking from even using an inspection mirror from on top or underneath. The engine runs great. I just finished replacing the power steering pump, ac compressor, dryer and hoses. What is back there? Freeze plug? Do I fear the worst and that the head or block warped? I may drill a hole from the passenger compartment to try and get a better view.
View 4 RepliesI am losing residual fuel pressure on my 1996 ranger 2wd, 3.0, V6. Acts fuel starved after sitting for awhile, cranks ok turn key off starts up, sometimes i have to do this twice.
View 7 RepliesMy Ranger has been a great truck but over the last 18 months ther has been a intermitent problem with the fuel system. It would run out of fuel ( foaming spray to nothing at the fuel rail ) and if you let it sit it would start and run after 8 hrs to a couple of days. Now it is all the time. The last time I let it sit for a week in a parking lot and it started, let it warm up and turned it off to move my other truck and it would not start when I returned. I have changed the fuel pump 3 times, 2 fuel filters, relay and pressure reg. on fuel rail.
View 5 RepliesMy 1996 Ford Ranger's Fuel Pump- Fuse keeps on blowing... (Fuel pump is new)... We need to find where the short is coming from!
View 2 RepliesI just had my codes pulled on a 96 ranger 2.3l came up with p1311 or p1131, couldn't quite see, but it said fuel air metering. What this might be, they said that a dealer would have to put it on a machine to narrow it down....
View 14 RepliesMy fuel gauge is stuck at the full mark. What to check and where to start?
View 7 RepliesI'm dripping fuel on top of the engine at the fuel filter . Where the line ties into the filter canister, there is a small plate that's attached with small Allen screws its dripping between this plate and the canister .... I assume there is a gasket/oring that is causing it ...... What is the part number or correct description so I can go to ford dealer and get one. It's a 2007 Ford 4x4 6.0 diesel.
View 2 RepliesI got a 1990 ford ranger 4.0l and is been leaking fuel from where the regulator conects to the fuel line the regulator is new. I cant find a new fuel line.
View 4 RepliesI let my sister borrow my 1995 4 banger Ford Ranger for about a week. To make a long story short, when I drove it home I could smell a really strong gas odor so I pulled into a gas station and noticed gas pouring out of from what looked like the fuel filter area right under the driver's side.
Anyway, it took another 5 gallons to get home and I later crawled under and took a look. It looks like someone grabbed the fuel line and tried to unsuccessfully pull it out of the fuel filter by hand. I could literally see the imprint of the person's hand where they grabbed the line. They had pulled the line so hard that it crimped and split which is why gas was leaking like a water hose.
I picked up a Ranger specific Dorman fuel-line repair kit from Advance and had my brother install it for me as I'm no mechanic. It was fine for a few days and then I started to smell gas again so I crawled under and took a look. There's just barely a small leak coming from the connector barb/union on the kit. Anyway, I didn't know what else to do so I dropped the Ranger off at a local shop this evening. With that said, this is fixable, right?
I'm dripping fuel on top of the engine at the fuel filter . Where the line ties into the filter canister , there is a small plate that's attached with small Allen screws its dripping between this plate and the canister .... I assume there is a gasket/oring that is causing it ...... What is the part number or correct description so I can go to ford dealer and get one.
2007 Ford 4X4. 6.0 diesel
On my 2011, I have been running AC in the normal setting and in max setting, but don't get the water dripping on the ground like I am used to seeing, especially with the high heat and humidity. My 2000 truck used to make lots of water and the wife's '09 Flex does too.
Is this normal with the new trucks?
I have written a lot over past years about my 2002 Sienna. It has always been very low on oil consumption, even over 200,000 miles.
In Sept/Oct during my annual visit to the States it used a quart in 3200 miles, which is more than in the past.
Last week, for the first time ever, I saw oil under the car on the concrete. First thing I looked at was the drain plug. Solid, and no oil on it.
Then, the filter. Ditto. No oil on the bottom nor under it.
I looked further and there is oil around the edge of the metal part on top of the motor which is obviously the valve cover. So, I am assuming the valve cover gaskets are oozing based on where the oil is visible.
But, first, I will check to see if the screws on the cover are loose, just in case.
As time passes, I will look around in other places. I realize a quart in 3200 miles is not the end of the world, but if I can make it better, why not?
If I can, I will wait until my next trip to the States, next October to do repairs other than checking for loose bolts/screws.
I've got a late 99 7.3 truck that I just recently did a lot of work on. I installed a new turbo with bellowed up pipes and a new exhaust system and when I went to start it up it started leaking fuel in the back pretty badly. Initially I thought it was the banjo bolt or the passenger fuel line but looking at it more closely I realized that it's not coming from there. It's dripping all over the side of the starter and is collecting at the low point of the metal lines down below. I also saw small droplets coming out of the up pipe where it meets the manifold but it looked like nowhere near enough to produce the kind of leak I'm seeing, also I know fuel shouldn't be coming out of the up pipe to begin with. This is really annoying and I would like to drive my truck again.
View 14 RepliesMy 96 ranger had lost a brake pad coming out of the mountains. I replaced the rotor but the ABS light came on as well as the check engine within a week. Several issues the clock spring was bad, replaced. The cam position Sensor was bad, replaced. I had this at a shop in a small town. While I was there they ran diagnostics.
At first the ABS module was sending data and gave them some info. Suddenly there was no more data stored in the module. They ordered a new ABS module installed it and replaced the LF sensor cable. Both sensors were cleaned prior to this.
The new abs module required a trip to ford to reprogram. At the shop they still could not get the light out. I took the truck home to my ford dealer and they said bad abs. Got a new (rebuilt Mfg discontinued) Installed and ford said this was bad with a code c1102. 4 w 4wd installed needs 4 w 2wd. ordered a new abs. Ford said same code again and the tech said that the ABS is not communicating through the obdii port.
My thoughts are the reader they used at the small shop was defective and either shorted out something or blew a fusible link. I am told this is 4 wheel abs with the rear sensors are on the pumpkin but after looking at the diagrams I do not see a RABS fuse. I have tested all fuses, and the shop replaced several relays. The pcm and ABS diodes check ok. Perplexed.
My engine has 2 ignition coils, and b went bad, but which one is b. ?
View 9 RepliesI have a 1996 Mazda B2300 & I heard that it is similar to the Ford Ranger.
Well the thing won't crank or start.
This is what I have done so far. I wanted to put a RPM meter on it. I followed YouTube videos on how to do it. I cut the Tan wire w. the yellow stripes & try to connect the wire to thr RPM meter. Then it won't start soo idk what to do. I also took put the PCM too. (I was looking for the wire) Now be honest, I talked to a mechanic, he said thag I might have blown my PCM or Blown another fuse. But when i put the key in to crank, it won't start ot click at all. The lights come on & it wants to start but won't start.
Then my mechanic tried to start it by the... Idk what it is called but you can start it & it wont evet start. It will crank like crazy but will not start at all.
I have a 96 Ranger 3.0 auto that is hitting 300,000 miles. I've got a 302 that i build for my F150 but know i'm thinking of transplating it in the Ranger. Is it a big deal in putting a SB in place of the V6.
View 4 RepliesI seen on this site awhile ago something about a fix for the heater control door, I have a 1996 Ranger and all I have is Hot heat and cannot cool it down with the temperature control.
View 2 Replies