Ford Ranger / B-Series :: 1996 - Engine Missing And Battery Gauge Fluctuation
Sep 16, 2014
I have a 96' ranger that has been missing quite regularly. The vehicle has over 200,000 miles on it, but has been taken care of regularly by me since 75,000.
Problem: When I start the vehicle, the engine takes a little bit to find the idle. It spits and fumbles around some until it finds a somewhat rough idle. Often, when I first start driving in the morning, the vehicle really jumps around due to misfiring. Even after running smoothly for awhile, the vehicle with sporadically misfire with no rhyme or reason. This is particularly true when climbing a grade. When sitting at a red light and idleing in gear, you can definitely feel the truck shaking from side to side. Also, when idling in gear, the battery gauge on the dash fluctuates, but when the vehicle is in park the battery gauge doesn't fluctuate...it just idles a little rough.
I had the Ranger to a garage and had them check the battery and alternator connections and ground to try and figure out what is making the battery gauge fluctuate...alternator and battery checked out...no diagnosis for fluctuation.
I replaced all plugs and wires and also checked the coil pack. One of the coils (#6) had some build-up in the top. I cleaned it out and replaced all the plug wires and everything snapped in place and fit fine.
The garage did tell me that an error code came up with the EGR valve and or sensor. They didn't seem to concerned about it. Do the EGR valve could be the cause of all the stuttering and misfiring going on with the ranger? I really don't know where else to look. Maybe replace the coil pack?
View 3 Replies
Advertisement
I was driving around town and I kept noticing my aftermarket radio would shut down and turn back on when I put my foot to the floor, then I noticed that my voltage gauge would shoot to the H when I hit around 3000 rpm and all the dash light's and head lights get brighter but once I let off the throttle it goes right back down. I've been taking it easy lately and now around 4000 rpm it will shoot up now. But I just replaced the voltage regulator I checked the battery and cables they don't seem to be damaged and I already replaced the belt. What could cause this?
View 3 Replies
1996 4x4, manual trans. Wants to kick out of first, and when shifting into 3rd I have no gear. Doesnt grind, just goes in as though it were neutral.
View 4 Replies
My fuel gauge is stuck at the full mark. What to check and where to start?
View 7 Replies
my 03 ranger 4.0l was working properly and all of a sudden I am having an issue. The battery light is on, and the volt gauge is just above L. With my multi-meter I am showing 14 volts on the output stud on the alternator, and 13.5 volts at the battery while idling. When I turn the lights/fan on I show minimal draw at the battery. Not sure if these are good checks but I figured a good place to start. Where/what should I begin checking?
View 2 Replies
2002 ranger edge 3.0 5spd. Truck idles perfect, but when you get rolling and higer rpms feels like the engine is missing. loos of power and shakes. I replaced the usual, plugs and wire's, seemed to work for a bit but came back. I cannot get any info on the scanner and have checked all the fuses. I am thinking coil pack but don't understand why it idles perfect and only misses under acceleration. No check engine light on.
View 5 Replies
2002 ranger edge 3.0 5spd. Truck idles perfect, but when you get rolling and higher rpms feels like the engine is missing. loos of power and shakes. I replaced the usual, plugs and wire's, seemed to work for a bit but came back. I cannot get any info on the scanner and have checked all the fuses. I am thinking coil pack but don't understand why it idles perfect and only misses under acceleration. No check engine light on.
View 14 Replies
Changed my oil today. Noticed oil coming off the front of the engine. Where this could be originating or do I need to take the belt cover off? I hate having a leak. Wanna get it to stop. Just need to know what I may be up against. 1996 2.3ltr.....
View 9 Replies
I just received this ranger and have never heard an engine sound like this before.
[URL]....
View 14 Replies
Got a 1996 Ford Ranger with the 4.0L in it that has a misfire on the #3 cylinder and giving check engine code: P303. Have tried new plugs, wires, distributor, switching out the coil pack with a known good, checked injectors for pulse, checked injectors, moved injectors and still the misfire remains on #3. Removed the valve covers and all appears to be well.
View 14 Replies
My 1996 Ranger runs ok but my check engine has come on. Using a scanner tool, indicates my cat monitor wont go to ready state and my error code is P0141. According to my research it indicates one of my 02 sensors. How to determine if its the one before or after the cat converter? About 6 months ago I had an exhaust leak repaired around my converter so I know I cant return it under warranty . If its the rear sensor , It looks fairly easy to replace but the front sensor looks a bit cramped.
View 6 Replies
I have an '02 Ranger 2.3L 40k miles that will not turn over even with a good battery. When the key is inserted and turned, all the dash lights and headlights come on but the engine does not turn over. Could it be....
*Power Control Module?
*Ignition Module?
*Key?
*Whatever the part is called that reads the Key's security code.
*Clutch Switch?
I am trying to avoid getting the run-around at the dealer and be able to drive to work on Monday!
View 13 Replies
I have a 98 Ranger with a 3.0 (5 speed) that has 254,000 miles on it. I drove it to town this morning (8 miles) and it ran normally. I stopped for just a few minutes at a house and when I re-started the truck, it was missing very bad and the CEL came on. It wouldn't haul itself in anything higher than 3rd gear. I decided to try to make it back home. I drove it less than two miles and it cleared up and started running perfect again. I came home anyway and read the code with my scan tool.
It said that I had a miss fire on cylinder #5. I erased the codes and shut the CEL out and its been running perfectly ever since. (I have put about 150 miles on it so far) If it does it again, I will start by replacing the plug wires. I have already done that but its been a long time ago. The plugs have been replaced twice as well. I was wondering if it could be something other than electrical like a dirty injector or maybe the compression rings lined up and it momentarily lost compression.
View 14 Replies
I have a 2001 ranger 2wd with a 2.3. It has a miss when acceleration. There is no check engine light. I have changed: fuel filter. Plugs, wires, crank position. Sensor, cleaned mass air flow sensor. Ran 2 bottles of injector cleaner in it. Still missing???? It runs and idles great. Just has a miss in the lower RPM's 1000-2000 then goes away. I really don't wanna take it to a shop. What do you all think??
View 11 Replies
85 ranger 2.3 fuel injected misses at high acceleration. Fairly new plugs and wires, just replaced the timing belt, pretty new fuel pump in tank, new fuel pressure regulator and pcv. It idles well, starts up and drives pretty well until you get it in 4th and really bog it down. Could be timing issues but I'm pretty sure I did everything right when I put the belt in. What it could be? I know when the tank fuel pump went out, it did something similar for a while...
View 9 Replies
I've got a 1988 2wd Ranger with a 2.9l v6. I just recently got it running. It has been setting for awhile. I replaced fuel tank, both pumps, fuel filter, Plugs, Wires, Cap, Rotor, TPS. It ran great for about 100 miles. Then yesterday on my way to work about 4 miles down the road it started to miss/stumble especially at about 55mph while in overdrive. When I got home I pulled the codes and I got KOEO 22 Map sensor signal out of voltage(engine off), 53 TPS signal voltage to high, 95 Thermactor Air System Problem, or Fuel Pump Monitor signal, indicates circuit problem.
KOER I got 21 ECT sensor signal voltage out of range or loss of signal during normal operation or Crank Sensor problem, doesn't have a crank sensor I believe. But I did change the ECT sensor and it still stumbles and seems like it misses. Noticed it is sluggish getting up to speed kinda surges and bogs. Im at a loss it isn't showing any more codes. Checked all plug wire connections and made sure everything was making connection. The only other thing I can think of is that the ignition module on back of distributor is going bad. Not advancing the time correctly.
View 14 Replies
I've a 1994 Ranger XLT 4.0L with a missing fuse panel cover. I'm trying to get the horn to work and we've traced the problem to a missing fuse. Unfortunately, there are 3 empty fuse slots and no info on their rating or use. Where I can get the proper info. Truck was a salvage, no ops manuals, and sloppy work putting it together.
View 14 Replies
4.0. I'm having what feels Like a Miss on Light throttle/cruise. Once warmed up it's fine. Idle is fine too. There is No CEL/Codes.
View 14 Replies
I live in Kansas and was home in Georgia for the last 2 weeks. The truck drove great there after a fuel up started missing and surging at 50 to 70 thought it might have been bad fuel. waited till it was low added Lucas fuel treatment and premium gas still was doing it. no check engine light. went to Advance and fuse for light was blown they checked and was getting mass air flow code. unplugged it and seemed to be better, not perfect but better. plugged it back in and went to do it again. Changed mass air flow night before the drive back to Kansas. Ran well from Savannah to north Georgia then started doing it again the rest of the way home. Going to have advance check code again.
View 12 Replies
1998 4.0 ... She only misses about 30 seconds during stone cold startup. I figure it's probably the plug thats hardest to reach ? Isn't that the way it always is? From the hood I can see only one spark plug, so I figure I'll do all the plugs. Is there any right or wrong approach to the plugs? I did the thermostat today, but this plug job looks like it's gonna be a bitch. Time for some skinned knuckles Next is the right side O2 sensor, that looks like fun too. But I gotta say, this little truck is sweet. Great visibility and easy to park in the city. I really like her. She's a keeper. She needs some new sway bar bushings too, but no surprise with 127 K on the clock.
View 5 Replies
My 2000 Ranger standard 4.0 4x4, started spitting and sputtering the other morning just when i was gone up hills then it would quit doing it. The other evening it got to where it don't idle, missing very bad, and wouldn't even pull itself up a slight grade, and the wife said there was flames and sparks coming out the exhaust. Now it wont even try to start, it just turns over. I put a different coil pack, wires, and plugs, and still nothing. I pulled the gas line off the frame fuel filter and its shooting gas out, and I got gas to the check port on top of the engine.
View 5 Replies
