i have a 96 ranger with a 2.3l engine sometimes it will start right up and sometimes it has to crank 4 or 5 times to start i just gave it a tuneup and changed the oil and filter. should i run sea foam through the oil system,it sat for about seven years and i need to convert the idiot gauge to a real gauge.
View 2 RepliesI have a 1996 Mazda B2300 & I heard that it is similar to the Ford Ranger.
Well the thing won't crank or start.
This is what I have done so far. I wanted to put a RPM meter on it. I followed YouTube videos on how to do it. I cut the Tan wire w. the yellow stripes & try to connect the wire to thr RPM meter. Then it won't start soo idk what to do. I also took put the PCM too. (I was looking for the wire) Now be honest, I talked to a mechanic, he said thag I might have blown my PCM or Blown another fuse. But when i put the key in to crank, it won't start ot click at all. The lights come on & it wants to start but won't start.
Then my mechanic tried to start it by the... Idk what it is called but you can start it & it wont evet start. It will crank like crazy but will not start at all.
I have 2000 Ranger 4.0L 4wd, 5sp ...
Just in the last month or so as out temps have been dropping off I've been having troubles getting her started. It happens both when the engine is cold, ie first start of the day, and after starting when warm. It did it a couple times last spring, but then all summer and fall I didn't have any problems (warm outside air temps) but, now its happening again. I'd say any time the Outside air temp is 40F or less, I am worried it won't start. IF i get her to start, everything else is just fine and she runs like a top. Here are the symptoms and what I've done so far.
When I crank I will get a couple cylinders to fire for a second or two then it falters out behaving like fuel starvation. Then I crank again right away and nothing fires... just cranking over and over. If i wait a minute and crank again same symptoms or it will fire right up. Baffling!
I thought Idle Air Control valve and sticking fuel pump relay, so I threw new parts on, but no fix.
About 75% of the time if I turn the key on, hear the fuel pump running, turn key off and on, hear the pump again x3 and then attempt the start it is successful.
Unfortunately, I don't have a code reader, or fuel pressure test equipment. The check engine light is NOT ever on. DO I HAVE A FALTERING FUEL PUMP??? I've heard thats tough to change out.
I have a 96 ford ranger 4cyl 5 spd. I've only had it for a month or so, but I've noticed on cold mornings my odometer won't work. The trip or the total mileage. I can hear the odometer cable clicking. Once the cab gets warmed up it'll start working. It's only happened twice, at about 50 degrees or lower, so I can only imagine what'll happen once winter kicks in. Where to go from here? I was thinking maybe it needs to be re-lubed or something...
View 9 RepliesI figured something out on my ranger that has been bugging me for a while it was a third cly misfire so I changed the plugs and it went away for a while.the po told me he had just changed the plug wires so i didn't mess with those and it was an intermittent misfire so i changed the brain box because it was 15.00 at pull and save and it had been all updated boy did it run smooth for a while then the misfire came back. So I decided to check the 3rd cylinder plug wires and found out the one that is hard to change on the drivers side was badly rusted so i borrowed one off my windstar it was a little longer but boy does it run smoother and it doesn't die all the time and chug chug all the time now i just need to change the battery. i have already changed the clutch and the tranny twice i took one out of an 88 and it fit just fine by the way the engine is a 2.3 8 plug engine with over 230,000miles on it my next project is a timing belt and a heater core won't that be fun and yes i smell the antifreeze inside and don't like the stop leak like the last person put in.
View 2 RepliesJust bought this truck and no check engine light was on, went to get it smogged so I could register it and it had the following fault codes: P1443, P0401, P1131, and P1132. The truck seems to run great in my opinion and even gets really good gas mileage. There is a whistle intermittently from the intake manifold area though that is at times pretty loud.
Smog tech told me these trucks are "notorious" for the check engine light going bad and that usually the entire instrument cluster has to be replaced in order to fix it. I'm a very experienced motorcycle /small engine tech but do not have much experience with car/truck engines and especially not with emissions control systems.
Again it is a 1996 Ford Ranger 4.0 V6, 4 wheel drive STX with 185,000 miles on it. Where to start or what might be the source(s) of these error codes?
Removing fuel injectors-coolant contamination.. How is this done? I need to see if they are any good-or clean/replace them-after I accidentally left the clip off the hose running out of the thermostat housing when I drained my coolant last week and the first time I drove, coolant leaked onto the top of the engine/manifold depressions, getting onto and into the fuel injectors.
I tried to clean it up as much as possible the first time(finally got it going) but still a few days later the truck at times cranks but does not start-hot or cold. I assume my idiocy is the cause or maybe it is just coincidence of something else? From what I read from my symptoms it could also be the fuel pump relay, pressure regulator, coolant temp sensor, crank sensor.. among other things. My fuel pump is 1.5 years old, so hopefully that isnt it. Have the injectors possibly been contaminated to where I should just replace them?
94 Ranger, 4.0, Automatic, 280k miles. Normally starts and always runs fine. Sometimes will crank and not start. Fuel pump replaced Feb. 2015 and again Dec. 2016. Have had it towed 3 times. Always starts when it gets to the mechanic. Sort of reminds me of vapor lock on the old cars with carbs, because if it sits long enough after not starting, it will start, no problem. Never died out or even coughed when running and plenty of power. When I take off the gas cap, it sucks in air like a whale. Twice I did that and it will not start right away, but if it sits for an hour or so, it starts no problem. Just bought a new gas cap 10 minutes ago and looked in a Haynes manual and a " gas tank vapor valve assembly" is mentioned. I don't want to change parts just to see what happens. Mechanics say there are no codes shown.
View 1 RepliesI have tried about everything i know about cars on this truck!! It ran great when I got it until a head gasket got blown so I tore into it and replaced them both torqued heads to specs. Made sure valves wasn't to tight. Distributor is in correct spot timing is correct had ignition module tested good!!! Coil tested good replaced both fuel pumps and put new tank and sending unit in the truck b/c it needed it new fuel filter replaced return line firing order is correct 1 4 2 5 3 6 it is getting fire it will crank and crank sometimes act like it is going to start then not also I can get it to run for about 3 sec on 3 or 2 cylinders it seems to have plenty of compression as well!! only thing really I can think of that could be wrong is computer? Also one last detail tried pull starting it as well still wouldn't go.... V6 2.9L...
View 9 RepliesI have a 2000 Ranger 4.0L with intermittent no start. Have spark, fuel pressure is 55psi, temp sensors are reading correctly. When there is a no start condition I can pop the scharder valve, relieve the pressure on the fuel rail and it will start.
View 3 Replies1997 2.3 Ranger w/ 160,000 mi. Every few months it won't start, sometimes after just having been running fine. Symptoms:
-the dash lights will be dim or off completely
-the chime will be softer than normal
-the headlights will not work, or be dim
-the starter will sometimes briefly click, sometimes crank once, sometimes do nothing
-the emergency flashers will sometimes click much faster than normal
-if during one of these "episodes" it does start, the battery light will sometimes flutter on and off, and the meter will flutter a little higher than normal. The next time I stop it, it typically will have the same problem.
-it will typically start if i get it jumped
My battery, starter, plugs and wires are all fairly new. On occasion, when it is having this problem, and I am trying like crazy to start it, if when I turn the headlights on and they are no longer dim, it starts right up and runs fine.
Getting the Banana ready for it's smog test appt at the shop last night (it WAS today) Check engine light had popped on and it had been starting to sputter and surge at the idle occasionally for the last few days so I took a look at the MAF and saw dirty wires. Aha I can fix that, a couple squirts of MAF cleaner, plug it back in and voila! No more light, the Banana ran down the road around the block, over the hill and through the dale like a champ. I shut her down and call it a night.
This morning, hop in and fire the Banana up like usual and all I get is a nice peppy crank over. The Banana has had a bunch (pun intended) of new parts throw at her recently... new battery, starter solenoid, plugs and fuel pump relay and fuel filter. All within the last couple of months.
Out of complete disbelief, I ground on the ignition for a little while and she finally kicked over and sputtered to life. I let her idle a couple of minutes and things seemed fine so off we go. I make it about a block before the Banana starts hiccuping and bucking like something possessed and dies.... kaput.
The Banana has a 3.0, manual transmission and at least half a tank of fuel. Long story short and a tow truck ride home again, half a day trying unsuccessfully to pull a code, any code.... nothing. She will half-heartedly cough and spastically run with ether shots and near as I can tell I'm not getting fuel to the fuel rail relief port. I'm really hoping there is some way to diagnose a faulty fuel pump without having to drop the tank and fish the damn thing out.
I'm not hearing it run when the ignition is turned on but then again I don't think I've ever heard it run. Any other things to try before I replace the pump itself???
I have a 2005 Ranger 4x4 4.0 automatic with an intermittent no crank, no start issue, So the problem has been getting worse over time This time when it wont start, all of the lights work, the radio, the fan, etc. They are all bright and functioning.
The battery is brand new and showing 12.9v at rest. (Yes, I have tried to jump it and charge it to be sure). However, The gauges are not functioning when the key is turned. I have no click, the lights don't dim, nothing happens when I turn the key.
Another neat point, if I turn on a directional with the key on, the relay clicks so rapidly that it won't even flash the lights. I am assuming that it is a ground someplace, but I dont even know where to start on this truck.
2001 Ranger 3L v6 auto, 186k miles. Never had a problem. One day last month I park it at home. 10 minutes later I need to make a quick trip . Get in, turn key, absolutely nothing happens. Replaced the battery, starter/solenoid, and ignition switch (not the key cylinder lock, but the white box inside the dash below and to the left of the steering wheel...has lots of wires going into and out of it,...turning the key slides a little metal pin inside it up and down). All fuses and relays are good, neutral safety switch is good. Key lock cylinder is mechanically working properly. Engine is not headlights, interior lights, wipers, radio, etc all work fine. Theft light is not blinking rapidly. Headlights do not dim when ignition key is turned. Where do I go from here?
View 2 RepliesI have a 1996 Ford Ranger XLT Automatic with a 4.0... A few months ago I went to start it and it would not start. All the lights were on and working, the radio worked etc. I figured it was the fender solenoid so I replaced it. Didn't fix it. I jumped the solenoid and it spun up. The only way I can start the truck is by turning the key to on, and jumping the solenoid. I replaced the ignition switch that is under the instrument panel, and the ignition cylinder that the key goes in to. I have reason to think that it may be the neutral safety switch, but I do not want to go out and buy the part and it not be the issue.
View 14 RepliesI just received this ranger and have never heard an engine sound like this before.
[URL]....
So I just finished redoing my head gasket. Everything is hooked back up the way it was prior to the tear down. I'm getting spark, fuel, compression, timing was set correctly according to Haynes, turns over but just doesn't want to fully start up.
View 3 Replies1999 mazda B4000 4WD 178000 miles 5 speed manual, I've been having a crank no start problem but after a few tries it would start, a week or so ago it was really cold (23) it wouldn't start so I opened the air box and shot it with starting fluid it took about 5 long sprays but it started.
It ran up op 3200 rpms and won't go back down, took it to my shade tree mech. he hooked it up to the diagnose thing it showed no codes, he poured water over the motor it different places and toward the back it idled down for a second so he says "blown intake gasket' so we replace upper and lower and sure enough we could see where there was a bad spot on the upper and a cleaner spot on the port.
That was not the problem it still idles at 3200, I mean wide open screaming, could the starting fluid have done something? Now he says "blown head gasket" I never had any idle problems before matter a fact besides the hard starting problem that started it was running just fine, what happened?
1998 Ranger, 3.0 liter manual transmission. The vehicle recently has had the engine replaced. Still a 3.0 Liter, but possibly is from a 1995 or 1996 Ranger. Replacement motor from a wrecking yard, appears to have been sitting for quite some time prior to purchasing. I had a friend change the motor out after getting the vehicle a few weeks ago.
Ranger drove fine for a week, but this morning it wouldn't start. One click is all it would give when you turned the key. Thinking the culprit was the all in one starter/solenoid, I replaced it with a new one this morning. Now the solenoid will click continuously when the key is turned, starter still will not rotate then engine.
Battery tests good - 12.4 volts; connections appeared fairly corroded.
Here is what I have done:
- Clipped off the first half inch of corroded terminal leads, replaced both sides with new battery connectors and wire brushed connections off at battery and starter.
- Replaced Starter
- With "S" connector disconnected, attempted to bypass starter connections and short terminals to see if a faulty clutch position sensor was to blame; shorting did not produce anything other than turning the key did.
- Paralleled an additional cable from battery to starter terminal to see if corroded wire connections were to blame; still just clicked repeatedly when attempting to start.
Crankshaft does rotate manually, does not appear to be seized up. Unsure of what else to check for. Not confident in friend's engine installation abilities, he may have screwed up something I'm not thinking of. On the other hand, I don't believe I would have been capable of swapping out the motor myself.
My mazda b 3000 shut off while at a red light i t turned over initially 3-4 times now nothing. changed EGR, ECM, CRANKSHAFT AND CAM SHAFT SENSOR three weeks ago. brand new battery, took alternator in and it was bad so i replaced. theft light is blinking rapidly?
View 2 RepliesI have a ford ranger 1996 4 cylinder. The truck was driving fine then all of the sudden it shut off and wouldn't start... I checked spark and that is fine also changed fuel pump and made no difference. We also sprayed lighter fluid and that did nothing. It sounds like it wants to start but wont.
View 10 Replies