I have a 95 Ranger with the 2.3L and it is a five speed. I am having a starting issue. I have replaced the ignition switch, clutch position switch, starter relay and had the starter tested. The truck will not start with the key. I can jump across the relay and it starts fine but will not even click with the key.
View 3 RepliesI have a 95 Ford Ranger 2.3L with a five speed. I recently had a starting issue were I parked the truck, went into a store came back out and the truck wouldn't start. Figured it was the solenoid as I couldn't jump across it to get the truck to start. Replaced the solenoid. Still no go. Found a fuse in the starting circuit blown. Replaced the fuse and got it started and drove home. Next morning, I go to leave for work and the truck would not start. Got a ride to work came home and checked it over and found the starter locked up. I replaced the starter. Truck started for a few days and now I am having problems again.
Here is the problem I am having now. Starter is good. Proved that as I can start the truck by jumping across the starter relay. Checked the solenoid with a voltmeter and it is doing what it is supposed to do when the truck starts normal. Here is where I am scratching my head. I can start the truck sometimes and it starts just fine. Next time I try to start it, the fuse will blow.
Replace the fuse and it might work for a couple of starts and then the fuse will blow again. I jumped pass the fuse with a piece of wire for diagnostic purposes. Out of 20 starts, it only started normally 4 or 5 times. I have checked every wire I can see under the dash and have not found any obvious issues. I am at a point where I am so frustrated that I just want to push this 400k mile truck into the back forty and put it out of its misery like a lame horse.
I have a 1995 ford ranger v6 4.0 and for this week Ive been having a problem, stalling... It only happens when I do quick "stop and go" driving. Even sometimes at stop lights it wants to stall, the only way to keep it going is to keep my foot on the gas.
Now for a while when its cold or my truck has been sitting for a day or two the truck doesn't start on the first click.
I've had the fuel pressure checked, changed fuel pump, and starter. I have no check engine light on at the moment. Tomorrow I am gonna check with my scan tool just to make sure. But, it could be fuel pressure regulator, idle air control actuator, egr valve? How I should go along doing this?
I have a 95 Ranger 2.3 with a manual tranny. In the past I have had problems with this truck not starting do to a bad inertia switch and numerous fuel pumps. A couple of weeks ago I pulled the truck off of the driveway into the street and let it set there for a few hours. When I went to put it back on the driveway it would not start. I got it pushed on the side of the garage. I did my normal routine of doing a pressure check. I had no fuel pressure so I assumed that it was the fuel pump (as usual) so I dropped the tank and changed the pump.
I got it back together and it still wouldn't start. I checked the fuel pressure and the manifold still had 0. So I started my diagnostic. I have power from the fuse to the fuel pump relay. I then checked the wiring at the inertia switch and found that there is no voltage with the key on at the supply side of the inertia wiring. I verified continuity between power distribution block and the inertia switch. I put in a new fuel pump relay and it still has no fuel rail pressure and there still is no electric signal at the inertia switch. Where to go from here?
I have a 1995 ranger with a 4.0 it cranks just fine wont fire has alot of fuel spark it will crank and crack then it stop and acts like it is going to fire up and stops cranking. This thing has 253k on it.....
View 6 RepliesMy 1995 ford ranger with a 3.0 will not start. It acted like the fuel pump was going out so I replaced it. I also replaced cmp sensor and the camshaft synchronizer due to old cmp sensor broke and messed up the synchronizer. My truck is getting fuel and spark but still will not start. Where do i go next?
View 4 Replies1995 ranger. 132k miles. I have been having an intermittent starting problem. I replaced the battery which was 3+ years old. I thought that cured the issue because the truck started without a problem then, the same problem occurred. I started the truck and drove about 10 miles. Parked it for about 2 hrs. Went out and tries to start it. The engine cranked, but would not start.
Tried a second time and would not start.
I turned on the lights and proved the battery was good.
Tried to start it and it turned over.
I took it to a shop and they could not fine the problem.
I asked if it was a possible problem with the solenoid, alternator,
They said if it was those the engine would not turn and you would just hear a click.
They drove it for a week and it happened to their technician but he said he did not have his equipment to check it.
He got it started after a few tries as I did and got it back to the shop. Ran a scan.
Four codes returned that really did not identify the issue - P0231, P1701, P0340, P1270. They cleared the codes and drove it again. They checked the codes. It showed code P0340. The shop says the code states to replace the cam position sensor and installing an updated DPFE sensor.
I have been driving it for about a week on and the problem has not resurfaced yet. A friend whom I work with does some car maintenance told me it is a dead spot on the starter and to replace it.
I had my battery out for quite some time. When I put in a brand new battery my key was not recognized and my truck will not start.
View 3 RepliesI have a 2002 Ford Ranger, and it wont start at all. Ive replaced the starter, had the battery checked. Not the battery, took starter out, had it checked too, its not the starter either. Someone said it maybe a fuse? This is totally frustrating, and I need to get it figured and fixed asap. Its been going on for weeks., I had it fixed and then it just stopped. It wont even take a jump anymore.
View 4 RepliesI have a 96 ranger 4.0L shift lever was very sloppy and one of the torq bolt fell on the floor I used loc tite and tightened them up with no problem put everything back together and now it wont start. I think I checked everything even replaced the neutral safety switch, adjusted the tranny cable, checked fuses and switched around the relays maybe an ignition switch? I am running out of stuff to troubleshoot.
View 13 RepliesMy 03 Ranger 4.0L has become a mystery that has baffled every one I know. Everything was fine and I ran home to something from my house was in there maybe 10 minutes came out and the truck wouldn't start. it doesn't even crank over. out of the clear blue. I had a friend who works for a garage check it and he thinks timing chain. Since then I have been told it wouldn't just fall off sitting there with no indication at all there was a problem.
Thought maybe PATS system. Its in order. Put in on a computer from auto-zone and it shows a check engine light but the reading is there is no codes in the computer on file. I am at a loss. Its been months and I really cant afford to take it to a garage right now. Its the strangest thing ever no crank, no stalling just nothing I hit the switch it lights up like its ready to start and nada.
Removing fuel injectors-coolant contamination.. How is this done? I need to see if they are any good-or clean/replace them-after I accidentally left the clip off the hose running out of the thermostat housing when I drained my coolant last week and the first time I drove, coolant leaked onto the top of the engine/manifold depressions, getting onto and into the fuel injectors.
I tried to clean it up as much as possible the first time(finally got it going) but still a few days later the truck at times cranks but does not start-hot or cold. I assume my idiocy is the cause or maybe it is just coincidence of something else? From what I read from my symptoms it could also be the fuel pump relay, pressure regulator, coolant temp sensor, crank sensor.. among other things. My fuel pump is 1.5 years old, so hopefully that isnt it. Have the injectors possibly been contaminated to where I should just replace them?
My 1990 4.0 refuses to start when the air temperature outside is at approx 40 degrees or below. It will crank until the battery runs dead if I let it. At approx 50 degrees farenheit the truck takes forever to start and always backfires out of the tailpipe and intake manifold (blowing off a hose on the vacuum tree) before it starts. If I can get it to backfire, it will start eventually. If it does not backfire, then I can run the battery dead and the truck still refuses to start. This condition has grown from a little problem to a huge problem over the past 6 months. Here is what I have done so far, including regular maintenance items.......
KOEO test checked OK
KOER test returned code 77 multiple times (TPS).
Replaced Throttle pos. sensor
Replace Idle air bypass valve
Subsequent KOER test came back with no more codes except 11 - OK
Load tested battery
Made new heavy gauge battery cables for + and -
New plugs, wires
newer starter
Changed coil pack for known good one off my explorer
Visually inspected hoses for vacuum leaks, replaced 1 cracked hose
1990 Ranger ext cab 4X2 4.0L, K&N air filter in stock airbox, Pacesetter headers, single 2 1/2" exhaust, stock cat no muffler, 260K on truck, 104K on good used engine from my 1994 Explorer. Purchased Ranger brand new in 1990. A4LD w/ shift kit.
I have a 91 Ranger 4cyl. Tune up about 2 months ago. Mileage about 178,000. When the temperature gets below about 45 degrees, the truck will not start. It cranks like the battery has plenty of juice but refuses to start. Once the temp warms up, the truck will start first crank.
View 5 RepliesInstalled a new clutch and slave today. Kept the same master cylinder.
The problem I am having is that the clutch pedal will not go to the floor, and therefore the truck won't start. The slave is moving back and forth roughly 3/8 inch, maybe more. I am pretty confident that there is no air in the system.
If I loosen the pressure plate a little, the clutch will go to the floor. But tighten it back up, and it again only goes down about 75%. This is a late '95 so it has the self adjusting clutch. I did get the correct kit for it, as well as slave. It's like the self adjusting part is too far adjusted and won't let my slave travel as far as needed.
In troubleshooting, I did notice that I failed to get the dowels in the flywheel aligned in the pressure plate. I am old school and not used to dowels in the flywheel! The dowels are not hitting anything and are not preventing the pressure plate from seating on the flywheel. But it is something I'm going to fix if I have to pull the trans again.
For reference, I replaced the clutch because the slave cylinder was hanging up and preventing the clutch from getting fully released. Aka clutch slipping.
I have a ford ranger 1996 4 cylinder. The truck was driving fine then all of the sudden it shut off and wouldn't start... I checked spark and that is fine also changed fuel pump and made no difference. We also sprayed lighter fluid and that did nothing. It sounds like it wants to start but wont.
View 10 RepliesI just bought a 2000 Ranger. I bought it at company auction for cheap because it wouldn't start. The battery was dead when I got to it. I put a brand new battery in it since it has 155,000 miles. When you turn the key to the on position, the theft light starts blinking rapidly. It will continue to do so for about 45 seconds if you leave the key on; then it will go out. However, if you turn the key to start, all you hear is relays clicking. The engine doesn't crank at all. I jumped the starter relay and the engine turns over. I have the factory manuals for wiring diagrams and diagnostic procedures.
The theft system relies on trouble codes to point you in the right direction for testing. I borrowed an Actron code reader (like you get at Autozone) and it says there are no codes. I'm wondering, though, if it only reads the SAE standard codes from any vehicle and not the manufacturer specific codes like the theft system. I have gone through a few of the diagnostic procedures with a multimeter, but it's like looking for a needle in a haystack without the codes. So far everything I've checked has come back ok. Any common issues this might be related to? BTW, I've gotten bits and pieces of info about this truck from the guys who drove it. Apparently, it just wouldn't start one day and was parked for the next several months until I bought it.
The truck just won't turn over makes a rrrgh rrrgh noice like it wants to start, I push the gas peddle to the floor and I should smell a lot of gas but don't!!! I added oil when it died at the store last night and it started up but the oil stick indicates oil is fine??? Pulled the diode out this morning put it back in the truck would not start just made that noise but turned it off and reseated the diode and it started??? These things may or may not have anything to do with the problem. Could it be electrical or oil pressure gauge sticking or something else that I could tell my mechanic and he could fix so I don't get stuck????
View 14 RepliesThis has happened 3 times.
1st) pulled quickly over to side of road, shut off truck. It would not start then. Towed it to service station and it started the next morning (with no repair made). I wonder if tow ride dislodged the the blockage in fuel line(?). Always sounds like it's going to turn over, but like not getting fuel.
2nd) Went to leave work, truck wouldn't start. Towed to my mechanic and he replaced fuel pump. Thought it was fixed because it ran fine until just the other day.
3rd) Slowed down to complete stop in heavy traffic and it stalled. Would not restart. Again sounded like it was going to start but didn't seem to be getting fuel. Good samaratins pushed me off road. Had it towed to mechanic. Started the next morning without any repair or service. It's like the tow ride and bumps getting it off the tow truck dislodges what ever is blocking the fuel line.
My mechanic replaced the fuel pump, but I don't think her replaced the fuel filter.
Sometimes the check engine light comes on and truck will not start, the fuel pump runs non-stop.. when check engine light goes off,the fuel pump runs for a few seconds and stops,truck will start.... driving down the road check engine light will come on and truck runs bad.... 1993 ford ranger .....
View 1 RepliesWe have a 2007 Ranger. When the temps hit 32 degrees F or below, the truck won't start. The security system light comes on. We have to run through the security system reset process, sometimes a few times, before it will start. Afraid all this key turning is going to burn out the ignition. Don't have a lot of confidence in my Ford dealer as they replaced the brakes and put the shims in wrong. Local mechanic says it's probably electrical. Is there anyway to bypass the security system or can it be removed?
View 1 Replies