Ford Ranger / B-Series :: 1995 - Replacement Of Carrier Bearing On Drive Shaft?
Jul 22, 2012
I am driving a 95 ranger xlt extended cab with a 3.0 two wheel drive with an automatic transmission. the two piece drive shaft with the carrier bearing went bad at the bearing. i separate the u-joint just after the bearing and was going to remove the nut holding the bearing housing together but cannot get the nut off. now i'm also finding out that i need a bearing puller to remove the damaged bearing from the 1st drive shaft.
Its turning into something i may not be able to finish. i saw on line an idea where a guy replaced the 2 piece shaft with a one piece. he states that a 1 piece drive shaft, 1998 or newer would work and no need for this bearing. you have to remove the cross member. it sound easier than what i'm trying to do. i looked at some old posts and galleries but did not see an article. here is a link to his website: How-To: Swapping a 2-Piece Drive Shaft for a 1-Piece in a 1983-1997 Ford Ranger
View 7 Replies
Advertisement
My 96 ranger with a 5 spd manual and two piece drive line has the center carrier bearing going out (squeals,vibrates,etc.) I got the part no. from the dealer but they are obsolete. is there a one piece drive line i could put in and what would that take to do.i remember a thread on it somewhere but cannot find it in the search. i would prefer not to use aftermarket because they only have a one year warranty.
View 10 Replies
I noticed a strange vibration in the 83 Ranger I own, it has the 2.3 and a 4 speed. When getting up to speed around 35MPH it would start vibrating, and the speedometer needle would bounce around and read slower than it was actually moving. This would start in 3rd gear, and continue thru 4th unless I let off the gas while it was in gear, then it stopped and worked normally. I put a grease seal in the tail section when I first got the truck, and when I pulled the driveshaft again today the seal was mangled and bent, plus there are metal particles around the main shaft where the seal goes. I figure the tail shaft bearing is shot, and I also found damage to the yolk with the U-joint, the shaft has a worn spot about 1/3rd the way around.
View 2 Replies
i'm just wondering if i need to worry about preload and backlash if i just pull the carrier out and replace only the carrier bearings. would simply replacing the shims in there original side keep the specs where they should be with new bearings or would i have to completely dismantle the housing and start from scratch.
I only ask because you can move the entire carrier by hand and see the slack in the bearings but i don't seem to have any noises or vibrations coming from the rear end so i don't know if it's worth tearing into...
View 1 Replies
What is the size of the nut that needs to be removed so I can pull the carrier bearing off the drive shaft? I need to purchase a socket.
View 14 Replies
I purchased a 1990 Ranger 4x4 with a v6 from auction. Took it to local shop to have them check it for me. Found out that it has a 3.0 in it and mechanic believes it is from a taurus. Truck actually runs extremely well. Has a few codes due to the ECM is for an automatic trans. Now the problem. I was on the highway-in 5th gear. Terrible noise the nothing. When I got it pulled over. The drive shaft was hanging from the rear end. It had been twisted like a straw. The transmission side had the yoke only, and the tail housing was cracked. It rolls and the drive shaft at the rear end turns. I figured the trans locked up. I don't know what trans to look for---is a 90 2.9 5 speed the same on a 3.0 ??
View 6 Replies
I'm replacing my clutch components in my 89 Ranger with an M5OD transmission. While I'm doing it I'm going to replace the input shaft seal on the transmission. I'm looking for the torque specs for the housing that holds the seal.
Also, should there be any play on the input shaft? My transmission has never made any noise but I noticed some slight play in the shaft.
View 1 Replies
I just bought a 5speed manual 2004 ford ranger 4x4 and when shifting usually upshiffter 1-2-3 I get a mi8ld clunk when I looked underneath I grabbed and can move the from drive shaft clockwise about 1/4 inch is this normal and if not how do I fix this?
View 3 Replies
My mechanic tells me that the hold up or carrier bearings on the drive shaft of my 2005 Equinox need to be replaced. He says that about half the time this cannot be accomplished and that I might have to replace the entire drive shaft. From the research I have done, it seems that a press (?) and blow torches are needed to replace the bearings. I can't afford the new drive shaft, but I could afford to replace the bearings if I could find someone who was sure they could accomplish this.
View 8 Replies
Today I took the bed off of my 99 ranger. I was sitting on the cab looking down at the rear axle noticed the drive shaft was not entering the rear diff perfectly straight. As I looked further into it, I noticed the distance between the rear spring on the passenger side tire, is noticeably different. To visualize it, the wheel, at the bumper side of the axle, has a shorter distance between it and the leafs than the cab side. Not massive, but a few inches, and it's noticeable now that I can stand over it. I'm beginning to be very annoyed by this truck and it's previous owners, whom I take it , scammed my brother quite well with a $5k tag for a truck with so much not right with it. It's about to become my yard art for awhile.
View 8 Replies
"95, 2.3L, automatic. Stalls for a couple of seconds and nearly dies when shifting from drive to neutral or from drive to park. Doesn't do it when cold at high idle or when AC is on. It catches back up and idles fine but nearly dies when coming out of drive. Installed a new idle air control valve but no change.
View 1 Replies
I have a 73 F100 with a 9" rear end. I need to replace the drivers side axle shaft as the bearing retainer is starting to slide off and I'm not willing to take a chance a new bearing and retainer will do it again. They are 31 spline axles and have the ball bearings not the tapered rollers.
What year trucks can I find a replacement axle shaft? Any other thing I should be aware of in finding a replacement?
View 1 Replies
I had the universal joints replaced on my 1999 Ford Ranger now it vibrates badly starting at 45 mph and when I coast at 65 mph the vibration is very significant. The mechanic does not know what is causing this. I never had this problem before changing the U-Joints and I have 171,000 miles on the truck.
View 4 Replies
What Spicer Part #s for the rear u-joints would be? I'm not nailing down the right one. I keep finding numerous ones, 1410, 1350, 5-160....
View 8 Replies
So, my 2004 F250, CCSB, Fx4, 6.0l, truck broke the carrier bearing today. There is an annoying hum that modulates, the drive shaft has a lot of play and there is light visible at the top of the bearing. The problem is that it broke on a 550 mile trip to Franklin, TN and I need to make the return trip. Is there anything catastrophic that can happen running it this way?
View 14 Replies
I am looking to replace the carrier bearing and (u joints while I'm in there) on my 08 F-250. I do not have access to a lift so this will be done while on the ground. Am I asking for trouble by doing this on my back?
View 14 Replies
From what I've read, the procedure for removing and replacing the drive shaft involves pulling the upper ball joints and tie rod end from the steering knuckle--is it possible to put a floor jack below the lower arm (the load runs to the spring through the lower arm) and undo the lower ball joint to get the clearance required to remove the shaft?
View 9 Replies
Found some cracks in the outside of my driveshaft. 2002 Jetta 1.8T 5-Speed Manual.
Part number: 1J0 407 271 GJ
I'm guessing it's just rust/age. Honestly, I don't even know if this need to be replaced. CV boots are in perfect condition, now cracks or leaks whatsoever.
View 4 Replies
I replaced the seal the other day on my ranger because I noticed my fluid disappearing. Went ahead and changed the filter and fluid as well. Flushed the system, and I go back to my truck tonight and there's a huge puddle of trans fluid. And the output shaft seal is once again, up against the drive shaft. I've spent like $150 on trans fluid since Friday, and $1000+ to get the truck running again last month, so pardon me if I get edgy about her.
99 2.5 auto. I changed the trans pan gasket too. No leaks from it.
View 14 Replies
In 4 x4 ( 2000 ford ranger 4.0 ) and drive for a while I can smell gear oil burning off the exhaust looks like it's coming out of the right cv shaft? Is there a seal that goes first That's bad?
View 6 Replies
I started with removing the two bolts that hold the carrier bearing to the crossmember that attaches on each side of the frame, well the clip that basically would hold the "nut part" of the bolt on the top side sheared on both of them due to salt+calcium chloride.
It felt like there was a 6 point head up there so I tried fitting wrenches and sockets up on the other side, I finally got a good hold with an 11/16" wrench but it just kept rounding more and more. Normally I would just torch the heads off but the gas tank is right next to it.
Any tips for getting the carrier bearing bolts out now? I don't care if I destroy it they're easy to replace. Also I'm typing this from my phone so Incase my sig doesn't show this is on my 02 f250 crew short bed 4x4
View 2 Replies
