Ford Ranger / B-Series :: 1995 - No Spark / Leaking Head Gasket
Mar 1, 2017
My 95 Ranger has been a good truck in the 6 years I've owned it. I had to pull the heads to replace a leaking head gasket and wound up having the heads rebuilt due to weak valve springs and worn valves. I replaced the gaskets, installed the heads, get it all back together.....won't start. Fuel pressure is good. Found that there is no spark. While putting the crankshaft position sensor connector back on I noticed it didn't look too good. I replaced the connector and that's all I did and no spark. Long story short, after a lot of research, the coil pack, cps and coolant temp sensor were replaced and still no spark.
Everything has the proper voltage to it. After a little more research I found a post with the same basic issue. His issue wound up being the ecm. So I removed the ecm....it's a used one from a salvage yard. I've owned the truck 6 years so I have no idea when the ecm was replaced. It showed up today and will get installed when I get home from work. I also ran across posts about the camshaft sunchronizer and they should be replaced at about 80K miles. Since the truck has 289K I'll replace it. Still no spark. I'm hoping it's the ecm.
View 14 Replies
Advertisement
I have a 91 Ranger V6 4WD with 150K that has been sitting for 7 years. The last time I drove it (7 years ago) to a mechanic, who diagnosed it with a bad head gasket - leaking coolant and coolant in the oil.
What am I looking at as far as a project: besides redoing the head gasket, what else will I most likely need to do given that its been sitting 7 years?
View 6 Replies
I am working on my buddy's 1994 Ranger with a 2.3L I4 that has been going thru a large amount of engine coolant. The trucks has approximately 180,000 miles on it. When I had it parked on concrete I have not seen any signs of coolant on the concrete or any signs of coolant leaking. The next place I checked was inside the cab to see if there was any coolant from the heater core and there was not. The water pump has been replaced a couple of years back. I replaced the spark plugs today and did not see anything on the plugs that I would have thought were signs of coolant in the combustion chambers.
With that being said I have not worked on a vehicle with a leaking head gasket before. Would there be any visible signs on the sparks plugs? If so what would I be looking for? When standing in front of the vehicle with the engine running there is a slight smell of antifreeze being "vaporized". Are there any noted issues with this engine that would cause this? Are there any other things I should check? Could it be a leaking head gasket causing this? If so how can I check for that?
View 1 Replies
I have read all I could find on replacing a blown head gasket and and after absorbing everything that TigerDan posted on here, I dove in and began. After disassembling all the topside junk I finally got the intake manifold loose and got down to the head. I began undoing the head bolts and found two broken bolts. The head won't budge so I am calling in a cherrypicker. I don't know what kind of mess I'll find when the head comes off. I assume the head will be warped or the block may be damaged.
View 6 Replies
I have a 2000 Ranger, V6 4L, and I believe my head gasket is blown, my radiator fluid goes straight to the oil pan. It has probably been leaking for a while, I did not realize it was leaking internally, I had been adding coolant for a few months but thought it was my radiator leaking because it had a crack in the housing, so I had that changed, but then a few weeks after that It gave out. I drained, and flushed the engine twice, and just parked it. My question is, should I just have the head gasket changed, or does it need a new engine because it had been leaking for a while and not sure what kind of damage it has done internally.
View 3 Replies
Well I finally went and bought another Ranger. Pretty red 5spd 4WD long bed. I knew it didn't run when I got it (crazy leaky fuel line...stupid squirrels), and the owner was pretty sure it had a head gasket failure. He claimed it was blowing white smoke and using coolant. I hadn't been able to get it to run to verify that, but I can't see why he would lie about that.
I finally got the fuel line fixed today (FYI, don't waste your time or money buying those Dorman OEM connector patch kits at Advanced Auto). While we were cranking the truck, I noticed gas escaping the degas bottle the radiator was pressurized before the thermostat should be open. That to me says blown head gasket (crossing fingers it isn't a cracked head) for sure. I tried to get a picture of the dipstick, but in the light it definitely looks like peanut butter. I just wanted to make sure before the massive ordeal of pulling heads/top end work that will follow
Anyway, plan is to fix her up and get her back on the road! Some picture enjoyment .......
View 14 Replies
My 89 2.9 has gotten water in the oil. One year ago I pulled this engine to replace the crank shaft (defective Ford design 1/2 thust bearing created a nasty grove in the crank allowing it to slide back and forth1/4 inch), new bearings, oil pump, timming chain, all seals and gaskets (not head gasket). The engine had great compression so I didn't do any thing more. Now I have a leak. No oil in water. NO compression leaking off into the water jacket. No "steam" coming from the exhaust. I've replace the intake manifold gasket. It showed signs of water leaking through the gasket, actually bubbles of water trapped inside, so I hoped this was it, but I still have water in the oil. I have now removed the intake and driver side head (head gasket shows now sign of leaking). No signs of water in cylinders. Is it possible to have a warped intake manifold? I have removed it twice, and I was told that some V6's need to be slowly removed VIA de-torque the bolts. I didn't do it the first two times I removed it, today I did. I plan to remove the passenger side head tomorrow. I will take the intake down and have it tested for warping. I have read many stories on this web site of the heads getting cracks, but they all seem to be in or near the valves, I assume that allows water to be burned off as a steam engine OR compression being pumped back into the water jacket.
Is there any other source of the leak that I'm missing? Is it possibly my intake? OR should I go ahead and replace the heads?
View 14 Replies
Have a 2006 F150, head gasket leaking bad. It is the drivers side head. How many hours this job is? and does the engine have to come out or the cab have to come off? Has a 5.4L Engine.
View 3 Replies
My wife has a 2002 F-150 King Ranch 5.4l. Recently I noticed a oil smell and I had the mechanic take a look. He said the head gasket is leaking oil. Not a bad leak but it is leaking. The truck has 160k miles on it. I can't decide what to do...
What generally happens with a head oil leak? Will the engine crater or just keep leaking? My plan was to buy my wife a different truck and I would keep the truck, but I don't wont to keep it if the head leak is terminal for the engine...
View 4 Replies
Am wrestling with the ever-present value/worth question. My '95 Saab 9000 Aero developed a leaky head gasket at 155,000 miles. I had it replaced (after driving it several hundred miles over a week or so). The engine then became and continues to be hard to start. It idles roughly, and even stalls out when decelerating for intersections. The shop says that two cylinders have low compression. (no details on why) They suggested adding injector cleaner to the fuel, which did not solve the problem, or installing a new (used) motor.
View 19 Replies
I have a 97 with a 4.6 Triton motor I need to replace the head gasket on the passenger side number 3 is leaking nothing else is wrong with motor so I have it torn down to timing chain cover and ready to remove. do i have to take the drivers side valve cover completely off to take timing chain cover off or can I take to first 2 studs out of the drivers side front valve cover and side the timing cover off. I just want to replace the passenger side head gasket and get rid of truck.
View 6 Replies
I LOVE my Super Duty and with only 15k on it (have a company truck) plan on keeping it for a long time. I've had an EGR Delete and new Oil Cooler along with some misc things done to the engine and turbo, about 6g's worth. Now my mechanic at NCB is telling me that the reason I'm loosing coolant is that my head gaskets are leaking. I'm looking at another 5-7 grand which is a no go for me. I'm thinking of doing the work myself, especially since I've seen where i don't have to remove the body to do it.
Okay, here is the question, I've been having a hard time finding a comprehensive list of the parts I should be getting to do the job. Looking for a list or link on what I need to do it correctly and anything I might want to do while my engine is apart so I don't have to do this again?
View 10 Replies
I recently replaced the head gasket on a 95 Geo Prizm. Now when I tried to start it, all I get is the starter clicking. I tried tapping the starter solenoid, to no effect. The only electrical that I messed with during the head gasket replacement was to disconnect the battery.
View 4 Replies
Have my oil leaking-passenger side head gasket replaced (along with the drivers side for preventative measures).
To ease my mind at such an expensive repair on a truck I just recently bought, I was wondering what else gets replaced with this repair.
Obviously the head gaskets along with head studs, coolant and oil, but anything else? valve cover gaskets? intake gasket?
View 14 Replies
To all those folks that said I had a head gasket putting pressure into my cooling system and causing it to overheat, you were right. It is a 2003 F250 with 80000 5.4 l. I have had to replace mexhaust manifold bolts on left side (horrible job, couldn't get one out). Back fenders are rusted out, under the extended cab rusted, doors are rusting at the bottom. My friend/mechanic said it was time to get rid of it. I don't really have thousands of $$ for a different one, but also, replacing the head gaskets are in the thousands for a repair bill. I have looked at used 2008 250 4 door and they are 20000+++ sheesh, but a new one is out of the question. Do I get the gasket situation repaired?
It does not act up all the time, some times it never overheats, sometimes it will. Somewhat infrequent ( I had one mechanic look at it and he tried 3 different times, and it did not overheat. Temp gage will peg, coolant resevior will overflow, but is not hot (100 degrees). I dont have the really have the money to put into a newer model, but I am worried about being nickeled and dimed to death after dumping a couple of thousand into a head gasket, plus I suppose I need to have the other side manifold gasket/bolts checked too. It seems like low miles to be having issues, yes I realize all will rust, but this year, as evidnet in our area, was really suspect-able to rust.
Not worried about the body, is it worth it to spend 2500 for head gasket repair, or trade up a couple of years, less miles, etc. My worry is, I already had to fix 1 exhaust manifold gasket, know head gasket to fix a cooling issue, do I cut my losses and move to another truck, or spend the money for repairs. I don't really have money for either but want to make a good decision. Truck has not been abused and has been serviced as scheduled. Had to put on new brakes and rotors, as would expect, and ball joints too. Oil looks fine, no contamination, and coolant is clear. Will the head gasket get worse? As I said before, it is intermittent, but I don't trust it for long trips.
View 9 Replies
I have a 1995 GMC Sonoma pickup truck with supposedly a blown cylinder head gasket. It only has 53K original miles on it. It overheated and I had it towed to a service shop. They put in a new water pump, new coolant, new thermostat, new radiator hose and did an oil & filter change. Well, 100 miles later, I noticed my water coolant was disappearing and the oil pressure was rising. I brought it back to the same shop and after looking at it for five minutes they informed me it was a blown cylinder head gasket. They said they had no way to determine this when they were doing the repairs the first time. So, I ask the following:
1-Was it proper for the shop to do the first repair without checking for a potential head gasket leak?
2-Is there some type of testing that could have been done by the repair shop to check for coolant leaks into the engine oil? 3-Would I have saved money (labor) by having this taken care of at the time of the initial repair?
View 3 Replies
I just bought a 95' 3.0 V6 4 runner that had overheating issues that caused head gasket to fail. I fixed all the reasons it was blowing the gasket with a new radiator & thermo. Now, temp no longer an issue but the automatic trans is slipping but has been getting alittle better as I drive it more. I noticed the trans fluid was pretty burnned when I replaced radiator..so will replacing the trans fluid & filter fix this issue ? Or could there be another issue ? My check engine light is also on, I will check the codes soon. I am getting horrible gas mileage, but probly from the slipping trans I guess.
View 1 Replies
Working on a 2000 F150 with the 5.4 and as near as I can determine its leaking antifreeze externally at the front of the passenger side head gasket. Seems a little odd. The coolant is a nasty dirty orange color. With the truck running on the hoist it was dripping very steady off of the very front exhaust manifold bolt.
View 3 Replies
I have a 2000 Toyota corolla with about 170,000 miles and it is using about one quart of oil every 500 miles. The last couple places I took it to said the compression was bad in the number 4 cylinder. Another place said it was a leaking head gasket. Which is most likely, and is it worth getting it repaired given its age and mileage?
View 13 Replies
A year ago (to the day), my car (2006 Hyundai Sonata) died on me while I was driving it. My boyfriend came and gave me a jump. The car got home fine. The next morning, we went out to the car, and the battery had died, so we jumped the car again, and got to the battery place and bought a new battery. I was worried there was another issue with the car- but my boyfriend was all like "You are feeble woman who knows nothing about cars" (kidding, kidding) so I listened to him and drove the car off that afternoon. On my way home, car died again. So, this time, we got the car towed to a dealership to get checked out. Well, turns out the head gasket was leaking and there was oil in the alternator. SOOOO. The dealer replaced the head gasket for free because the car had a warranty on the engine, but we were SOL with the alternator. So, we bought an alternator from a friend, and had another friend install it for us.
Yesterday, I got out of work, and car wouldn't start. When my DF came to jump the car, he and I could clearly see the head gasket is leaking again and there is oil in the alternator. I have a couple questions that I need answered...
1.) What causes a leaky head gasket? My boyfriend said that either the engine block was warped or that the replacement they put in last year was faulty. Are there other ways?
2.) How the beep do you replace the alternator in the 2006 Hyundai? It is in an odd location and we don't have access to the person who did it for us last time, so I need to see if this is a job my boyfriend can do. He does work on his car all the time (an 87 BMW), but he's never done anything on this car besides change oil, etc.
A little bit about this car: We bought the car from a Hyundai dealer in June 2010. It belonged to one of the dealer investors, so it was in great condition. However, we think the car was in a front-end accident. When my boyfriend waxed the car awhile back, it was pretty obvious that the front bumper was replaced as well. The dealer refuses to give us any mechanical records about the car (will only give us verbal summary) ...
View 10 Replies
I have a 1998 Subaru Forester that is leaking oil through the head gasket. Repairs for the head gasket seem to be in high range, which is at or above the value of the car. Is trying any of the head gasket sealant products such as Blue Devil worth trying? Do they have the potential to do more damage than good? I love the car, but I'm also not sure if it is worth getting if fixed or if I should be looking to sell it for parts and buy a different used car.
View 15 Replies
