Ford Ranger / B-Series :: 1995 - Misfire In Cylinder 2 / CEL Flashing And Code P0302
Jan 11, 2017
I have a 1995 ford ranger 2.3 L dual coil packs new plugs, wires, coil packs, tps, idle air sensor, internal temp sensor, and a replaced mass air flow sensor from wrecker. That all said my one son missed a plug when i replaced it , it had no tip left on it , but since then i now have a misfire in cylinder 2 where the olther plug was found and replaced ...
Gap for plugs are .44
Used the wrecker maf to see if it would clear a p0113 which it did. I am stumped on why at approx. 30 minutes of driving that the cel will flash then set a p0302, no other codes no fuel smell. rechecked plugs all are clean haven't been able to check fuel pressure yet, and i out a can of seafoam in the tank to see if it clear out injectors.
Besides all, I will check injector to see if I hear anything but I'm stumped. Also we have to have an emission test so is it best to fail the test and will it show me what I'm missing.
View 14 Replies
Advertisement
Been awhile since I've been able to post but I've got a serious issue with my 2006 Ranger XLT 4L V6. So last night about 2 miles from home my check engine light started flashing like it was a at a rave and my engine wasn't acting right, also had the STRONG odor of raw gas, no other lights from the dash, no fluids leaking, oil was good n nothing in radiator but coolant. Was able to baby it to my current home but all my tools are in storage so had to wait to get my ODB scanner to see what's up. Scan came back as 'cylinder #3 misfire' & 'O2 sensor reading rich'.
Go cylinder #3 spark plug out and it were fouled bad. Got ride to the store and got a whole new set. Got back n got'em changed and fired ut up, idle still rough and check engine started flashing again and white cloud coming from exhaust pipe and STRONG odor of gas. Check and now have 'multiple missfire', 'cylinder #2 misfire' and 'cylinder #3 misfire'.
Shut it down go and double check ALL spark plug wires are connected and TRY to start, get about a turn n a half then starter spin. Try again and the engine won't even turn over. "Great I've seized the engine!" Was able to put a socket on the crankshaft pully and manually turn the engine over "whew didn't seize the engine", did this a couple of times and tried to start, was rough but eventually it fired up, still idling rough and again check engine light flashing, while it was running I pulled one plug wire at a time from the coilpack to see/feel the lighting and there was spark for the 3 I pulled, didn't affect engine idle.
Run codes and 'cylinder #3 misfire', so now that the engine is was warmed up I pulled out my ohm meter and started checking wire resistance. Cylinders #1, #2 were at .012, #3 was .011 and #5 was .009.
I've figured that the raw gas is due to cylinder #3 not burning and just pushing gas into the exhaust. So to the brass tacks, do I invest in a new set of wires? Or could it be the injector being stuck open and just flooding the cylinder? No when I originally pulled the #3 plug fuel did not spill out. Haven't pulled #3 again due to it being May in Arizona and had to take a break. I'm going on the assumption that the engine wouldn't start after a short run do to "hydraulic lock in cylinder #3", my manually turning the engine over cleared this and allowed the engine to start.
View 9 Replies
I have a 1999 ford ranger 3.0 6 cyl with 211,110 miles It started running rough without any previous warning signs. In idle its barely noticeable, once i put it in gear it gets rougher and when driving around 40 to 45 mph it roughly shakes and shimmies. Once I get past the 40 to 45 mph range it settles back down. Is there a specific issue that would cause that at that speed. When going up over a bridge the check engine light blinks.
I changed the spark plugs and new wires and it offered no success even though one of the plugs were black (to much gas). I have borrowed a diagnostic tool and got P0305 cylinder 5 misfire, I am thinking fuel injector to replace, what else should I be looking at?
View 3 Replies
1999 ranger 155k 3.0 flex fuel. 304 is misfire in cyl number 4... I replaced the plugs and wires and checked the coil. the compression in cyl 2, 4, 5, 6 and got 80-90 psi so they are consistent but consistently bad right, it may be my compression tester.
The #4 plug was spotless after running 5 min, the #5 plug had some black on it already. Its hard to tell but it seems I had fuel residue on the plugs on cyl 5 and 6 but none on 4? Whats next pulling the intake to get to the injector?
View 13 Replies
Got a 1996 Ford Ranger with the 4.0L in it that has a misfire on the #3 cylinder and giving check engine code: P303. Have tried new plugs, wires, distributor, switching out the coil pack with a known good, checked injectors for pulse, checked injectors, moved injectors and still the misfire remains on #3. Removed the valve covers and all appears to be well.
View 14 Replies
I bought this from my brother in better than mint condition. Always maintained. Its generating a cyl #2 misfire code.
It starts and runs like new when cold, but when it warms up, it idles rough, and generates the code. after 1500 rpm it smooths right out and runs fine.
He had it to the dealer just before I bought it and they told him needed a new engine.
I am thinking bad injector, since what seems to be happening is, when cold it gets more fuel, or when u rev it gets more fuel, but at an idle and warm, it doesn't seem to be getting enough maybe. And I see from the maintenance records, a couple of other injectors have been replaced as well.
I think the dealer got tired of replacing injectors under warranty and tried to milk him for a new engine.
2002 ranger extended cab 2wd, 3 door, 232,000 kms 5 speed 3 liter V6, new glass and clutch..
View 4 Replies
2000 4.2....Last year I had to replace the coil pack when it started running rough and had a code for a misfire on cylinder 3. It is doing the exact same thing now, same code, same cylinder. Is there something wrong that is causing this?
View 5 Replies
I just purchased a 2005 Santa Fe, 4WD, 2.7l..the engine has a miss...the code that came up was "misfire in #2 cylinder"..I checked the coil pack...and the wire harness just crumbled..so I replaced the coil pack...reset the code..and it was good for a couple of days...I got through inspection...today I put on the A/C..and the engine got rough..the check engine light came back on..same code..misfire in #2..I'm thinking the injector or what else could it be? plug? wire?
View 3 Replies
I have a 2010 accent GL manual sedan. It has 104,962 KM on it, the warranty expired December 18, 2015. Since February this car has become a frustrating money pit. Being in the dealership constantly for repairs, then within a week something else 'happens' and back it goes. Spent almost $5000 in 4 months on repairs. Decided that's enough and will do majority of repairs myself.
Yesterday while drive on the highway I had a sudden loss of power and a check engine light came on. My scanner which has become a standard item in my glove box indicated a misfire on cylinder 2 - P0302. I limped the car home, in 3rd gear I was having a hard time staying above 2000rpm at 60km/h. at lights I had to use hand brake so I could keep my foot on accelerator, revs were dropping below 300.
Today I replaced all the plugs (all 4 were still in good or better condition, #2 showed signs of a slightly rich burn and #3 a slightly lean burn), replaced all coil boots (no cracks, no burns, and still pliable), removed and cleaned all the injectors. Error code P0302 persists.
View 8 Replies
I have a 2002 Santa Fe 4 cyl that is giving me a problem that I could use some advice on tracking down & fixing . First & most important is a code P0302 # 2 Cyl misfire. How to check the ignition coil pack , injector ,& wire for this cylinder in home garage with normal tools & meter . Is there a you tube displaying how to do this step by step ?
The other problem which I don't have the code for at this time is that some part of the exhaust is not getting warm enough & this also put's the check engine light on . Will get back on this one when I solve the main problem Misfire.
View 4 Replies
I have a 2005 Santa Fe with the 3.5 with 112000 miles on it. I had the engine light come on with the code P0302 cyl #2 misfire, I got spark plugs, plug wires to do a tune up on it. I changed all of it and got it back together, started it up and it still had a miss to it. I then took the front spark plugs out and did a compression test on it. #2 was at 85, #4 was at 120, and #6 was at 160. I couldn't check the back cyls because I had already put the intake back on. I then did a wet test, and all the cyls came up to 160. So this tell me that the piston rings are bad in #2 and going bad in #4. I have kept all the oil changes up and up to this point I haven't had any trouble with it. Having this problem with there 3.5?
View 1 Replies
Getting error code p0302, misfire in 2, pulled the plug and had oil on the treads and on the lower part. My guess is the valve cover gasket, but I'm not 100 percent sure.
View 18 Replies
2000 Jetta 2.0 cylinder 2 misfire. Replaced plugs and wires. No check engine light but code is pending and there's still a misfire. Need to smog
Replace coil pack?
Swap fuel injectors and recheck?
View 3 Replies
2005 3.5L FWD. 5 days ago I left the house, the engine was running smooth at idle but having hiccups when accelerating. Check engine light went on when accelerating but going off at idle. Turned around at the first stop light, parked the car home and pulled code P0302 misfire on #2 . Figured it's most likely the coil, was going to order one next day but to my surprise, no more check engine light next day and engine has been running smooth since then. Probably drove 100 miles since with no issues. I have 6 spark plugs waiting to be replaced but it's too cold to do it right now unless it's an emergency. Car has 105k miles now, spark plugs were changed at 63k. Was this just a fluke and P0302 will probably not come back or should I not risk it and just go ahead and replace the coil? If I end up replacing the coil, should I do one coil or all three?
View 22 Replies
2001 Ford Ranger 4.0L V6... Okay so I bought my truck last September with 100K on it. Ran perfectly fine. No problems for for the first two months and then it started to misfire when at idle. Check Engine Light came on. Scanned and got a random multiple misfire code. I then changed the plugs and wires. Had to repair the threads for cylinder two. Did all that and it kind of but not really solved the problem. A few weeks later got another check engine light. Cylinder 3 misfire. Changed ignition coil. No better. Shortly thereafter I checked again whilst at work and read misfire on 3 and now 2. Currently replacing the intake manifold o-rings and cleaning out intake.
View 6 Replies
This has been an issue for about 8 months now. I'm getting a misfire on cylinder 4. So far compression test, new gas filter, fuel injectors cleaned, spark plugs and wires replaced. coil pack replaced. Heater valve was leaking but was replaced.
View 10 Replies
OK, got a check engine light today when I fired up the Ranger.
Took it down and got the codes read it have a miss fire on cylinder 5. Picked up some plugs and wires, got to get those E3's out of there, but kind of think that's really not going to fix the problem. So that probably leaves the coil pack or injectors.
So what's the consensus on the best coils to use?
Also, being an 18 wheeler for more years than I care to remember, I've learned swapping just 1 injector is never the way to go. So whats the best type of injectors to get and where the best place to get them should it come to that?
Oh, it's a 2000 3.0L Flex fuel 5 speed.
View 6 Replies
My parents 2000 Ranger has an CEL for cylinder 4 misfire, but it will clear on its own and then start up days/weeks later, is this common? Could it be an injector?
View 3 Replies
I have a misfire mystery going on in my girlfriends 00 ranger. What is going on, is there is an intermittent misfire on #4. I have an ultra gauge hooked to it, so most of the time when it does it, it will flash a pending code. A lot of the time, the pending code will go away, but sometimes it will set the PO304 code.
First I tried a tune up. New plugs and wires, air cleaner, cleaned out the throttle body. This cured it, for a short while. Then we were back to the pending code / setting code for #4.
When I pull the plug on #4 it is sometimes wet with gas. If you put a new plug in it runs fine for a while. In fact the last time we took a several 100 mile trip with it right after plug change, and it ran great. The pulled plugs re always in good condition with no burn, oil, chips or glazing. I have been using the standard autolites that are in advance auto's computer for that engine. No issues with the other 5 so I figure they re good enough.
The day after we came back I get the call... Honey its doing it again. Often to the point of having no power at all.
But it will clear itself usually, if not a new plug for #4 will cure it immediately.
So I thought something is killing this plug.... Or flooding it. SO I ran 2 cans of sea foam though it, put in a new plug and an new wire. It fixed it for a week then it did it again.
Ok I think... maybe the coil pack is bad either killing the plug or just not firing it at all? So since the pack has never been change in its nearly 300K life (to my knowledge, shes had the truck since about 60K) What the heck.... a new coil pack for the old thing.
I have not had the chance to clean the MAF but we are talking misfire on one cylinder, every now and then with no real conditions that set it off. More often than not its a pending code that you can even hear or feel and other times its a full blown miss that drags the truck down. Well for a short while until it clears up or I replace the plug.
3 cans of seafoam surely would have cleared a sticky injector. I realize it could be a bad wire to that injector but I have not had the time to tear the fiddle bits off to get to it to clean and test it... or just replace it.
Honestly Ive had a lot of cars and trucks, I don't remember ever having to replace an injector. Ive had bad wires to them but they misbehave ALL the time. This problem is so intermittent its freaky.
She says it does it mostly when its cold or not totally warmed up. Almost always, by the time the engine is hot it goes away.
And hot for this truck is over 185F, which I think its too cold to be running and the thermostat needs changed BUT she thinks cool=good. I keep telling her no, cool is often not good, the engine needs to be up to the operating temp.... which to me means 190-200. Her ranger runs between 170-180 all the time. I doubt thats causing the problem but still.... I think new thermo is in order.
My thinking is since it runs so cool all the time, the issue might be related to a spike in the temp over 180 ish, that gods forbid is opening a crack somewhere to suck air or lose compression.
And a compression test is my next step on #4 if/when it does it again. Now I have had cracked valves before, I don't recall them acting this way. After all sometimes the thing will go 100s of miles under different driving conditions and run fine. I don't think a cracked valve would be that nice.
Shes getting @18 MPG mixed driving, when it runs t runs like a bear. It always fires right up. There is no smoke, white or black. There is no water in the oil, no oil in the water. No audible exhaust leaks. No ticks knocks or oddball noises. For its age and miles almost 300K it runs perfectly.
Well until it has its intermittent issue with the misfire, that isnt bad enough to actually set the code.
View 14 Replies
I figured something out on my ranger that has been bugging me for a while it was a third cly misfire so I changed the plugs and it went away for a while.the po told me he had just changed the plug wires so i didn't mess with those and it was an intermittent misfire so i changed the brain box because it was 15.00 at pull and save and it had been all updated boy did it run smooth for a while then the misfire came back. So I decided to check the 3rd cylinder plug wires and found out the one that is hard to change on the drivers side was badly rusted so i borrowed one off my windstar it was a little longer but boy does it run smoother and it doesn't die all the time and chug chug all the time now i just need to change the battery. i have already changed the clutch and the tranny twice i took one out of an 88 and it fit just fine by the way the engine is a 2.3 8 plug engine with over 230,000miles on it my next project is a timing belt and a heater core won't that be fun and yes i smell the antifreeze inside and don't like the stop leak like the last person put in.
View 2 Replies
I am currently chasing misfire codes that started out on cylinder 5 p0305 was the first code I replaced spark plugs and wires about 200 miles the code returned checked coil with meter it was barley in spec. I have replaced coil same code only difference was a hard start cold or hot replaced injectors now hard start is fixed but logging codes for right bank is to rich and p0300 304 305 and 306 also performed compression test on right bank and readings are 155 155 and 160...
View 3 Replies
