Ford Ranger / B-Series :: 1995 - Just Died Suddenly And Won't Restart
Jun 2, 2013
My Father in Law's 95 Ranger, 4 Cylinder, 5 Speed has started acting strange. It has, in the past 3 weeks just died suddenly, and won't restart. No action at all when you turn the key, as if the battery is disconnected. Wait for 45 minutes to an hour, and it starts back up again.
He has had it to a local shop twice, and the only thing they have done is let it idle for 5 hours at the shop. Of course, it never stopped.
Now they are saying it is the clutch, and depending on the type of clutch, (big or small).
I've been working on cars most of my life, and even had an 87 Ranger, and I've gotta call BS on this. He says it happens mostly when coming to a stop.
View 4 Replies
Advertisement
My 2001 2.5 manual suddenly died. The starter turns the engine over, but I don't get a) fuel (changed the fuel pump) b) spark c) Engine check light. When I plug the OBDII reader in, it simply says "ERROR". No codes, no other language.
While trying to figure it out this morning, after trying to start it 50 times, it actually fired for a few seconds, but then died again.
I checked relays and fuses and nothing seemed bad. I swapped relays around too.
I unplugged the battery, then the computer, but nothing got it to fire again.
View 4 Replies
I jump started my wife's mini Cooper using my aerostar van 3.0l cargo. Her battery was so dead we had no luck after running my van for 8-10 min. There were a couple of attempts. My van suddenly died when she wasn't cranking the mini. It won't restart.
About one week prior I had a no start situation. I thought I had solved the problem. The first thing I did was listen for fuel pump engagement. I didn't hear it. I pulled the fuel pump relay and cleaned the connections. I put it back and the van started. I drove all week and then I get the call to jump start the mini.
So back to today. Fuel pump is engaging. I checked for spark at #4 cylinder with fuel relay disconnected so as not to flood the engine. I have spark. Battery is strong. I put a new fuel pump relay in place even though it appeared to be working properly. I had my wife crank the engine and the pink/blue wire at the fuel pump relay which goes to the pump lit up my voltage tester. Power appears to be present when cranking and not just initial engagement.
I'm thinking the original no start had nothing to do with the wire connections which I cleaned and it was just coincidence that it started and ran again for a week. The connections are now clean with a new relay attached and not starting. I'm thinking if I have spark and a fuel pump engaging then injectors may not be firing???
View 3 Replies
Wife was driving her car and went around a corner when out of the blue it died. Unable to re-start. I've replaced plugs, wires, coil pack and still no response. I'm not a mechanic and don't know where any of the sensors are located. I tried doing the self-diagnostics test but now none of the dash lights come on. Car cranks just fine. I've heard that it may be sensors, it could be the safety switch. It's a 95 Plymouth Neon Sport, 2.0 SOHC Five Speed manual.
View 3 Replies
My '93 Ford Ranger suddenly died while I was driving, no sputtering or bucking, it was just as though I had turned the key off. When i tried to restart, the engine would turn over but not engage. It's as though the engine is either getting no gas and/or spark. My shade-tree mechanic says he got a diagnostic code that was #539 followed by #1 seven times at two second intervals. he says he ran the test 6 times and got the same result every time. What this means?
View 10 Replies
Ford Ranger 20012.5LManual Transmission4 Cylinder Engine4x2 Drivetrain~160K Miles
While driving home tonight, my truck suddenly lost power, as if I turned the key to turn off the motor. There was a beep, the one that goes off whenever I open the door while the key is in or the light is on, then the "Check Gauge" light came on (the one that warns me when my gas tank is near empty), following that the yellow Battery light came on and finally the orange "Check Engine" light came on.
I pulled out into an empty dirt lot, but that was pretty difficult as the power steering was gone (since the truck was off). After parking the truck, I turned the key to the actual "Off" position, pulled the key out and gave the truck a few moments. I put the key back in and tried to get my truck running again. Of course, it didn't work, but I figured it wasn't the battery because it lacked the sputtering motor turn. There's that and the battery is under two years old. The truck seemed like it really wanted to turn and start, but it lacked a certain something to get it up and over that last hill to vehicular movement. I don't think I was lacking gas, since it should have given me the red "Check Gauge" light and even if I was, I know I have another 5 miles before I have to fuel up (I would know since I've tested it to see how far it would go on that light). I was pretty low on gas when this happened, so the thought came to me that maybe my gauge was starting to get a bit wonky. Then a more realistic thought came to mind.
I've had this bad habit for a while, where I fill my gas tank to only about a quarter or a half at the most. Part of it stems from a paranoia of having somebody siphon gas out of my truck at night; yes, I could have fixed this by installing a lock on the gas cap (albeit, my counter-argument is that it's better to have them take the little bit of gas than have hundreds of dollars of body damage from an aggressive thief). Anyway, I've heard that this habit of filling the tank below half can speed up fuel pump failures. Despite this, I've had no other symptoms of a fuel pump failure coming, as I haven't experienced any issues with surging/bucking.
So here are my questions:
1) Am I right in assuming it's a fuel pump failure?
2) Are these instructions to fuel pump replacement accurate? (Yes, I know the DIY Matrix provides every reason on why I should avoid doing this myself, but my wallet I'm itching for a project.
3) If it's not a fuel pump failure, what could it be?
View 12 Replies
My MILaw Truck 1992 ranger isnt running good and I need to get it going
Only a P0111 at this time IIRC
We started the truck tonight and idel ok Could see the motor Stumble every so often. She went to drive it and it Cuts out under Load Or you must rev it up to keep it from Stalling.
And if it does Cut out you have to let it sit for 5 minutes to restart what is Weird is it dont Smell Flooded either I smelled the VAC Line to the FPR and it was DRY and Did NOT Smell like Fuel.
It was dark didnt do much trouble shoot as the Flashlight died. I wonder about Fuel Filters. And Also about the Idel Control. The Mis or Stumble seams Random
Any testing I can do I have a DVM and that Code Reader. Might have to find something to check fuel press with where would I check it at the fuel rail I assume. Going to try and go over the Basics tomorrow If there is Anything Specific I should check?
View 14 Replies
About a month and a half ago I was doing 70mph down the highway and the truck began to lean out sputtering and sounding like fuel was not getting there, when I pulled over on the side of the highway because it killed itself and then the car would not start I noticed the ox sensor for the 3rd cat was ripped out from being caught on the driveline, I removed ox sensor and car still wouldn't start. I took the truck to my buddies shop and after a new ox sensor was installed with some effort the truck started 30minutes later, I did not think this was reason for the truck to not start but after a day it was running like a top again, little did I know. Last week driving down the highway ironically in the same spot as before the truck did the same thing sputtered to a stop and would not restart.
Side Note: on both of these occasions after the truck would sit for a day it would start run for about 5 seconds and die???? So I had it towed home again and began reading FTE, I saw posts about fuel pressure and spark and P0176 code for Flex Fuel, Inertia Switch and so on.
So I started with Fuses they all look good then the most popular post and 2 of the codes were P0176 and P0177 for flex Fuel they read OBD II flex fuel wont start....Another code was for EVAP and 3 codes for heater bank(it turned out to be a fuse but is or could something trip this to send the car down this path?
I Then figured I would try the Fuel Filter..This did not work.
2nd I tried was Fuel pump pressure is good based off others posts.
So I bought the Flex Fuel Replicator that eliminates the need for the flex fuel sensor, from the guy in Portland, well this didn't work either. Next I went to spark checked all plugs they smelled like gas and were slightly fouled I had just replaced these about a year ago but hell why not? so I replaced and got nothing still also checked the oil had some gas smell to it but my buddy said this was normal with trying to get it to turn over without success.
Checked inertia cut off it was normal, checked fuses they were good(except heater which has been replaced). Now I am stuck...
View 14 Replies
I have a 86 Ranger with the 2.3L fuel injected 4 cylinder and a 5 speed manual transmission. I can drive it for hours on the highway but if I get caught in stop and go traffic, it stalls and won't restart for about 10 minutes. When trying to restart it acts as if it is fuel starved. Spraying carb cleaner in the throttle body does make it run for a second or two. I was getting a code 18 & 67 before I changed the ignition module, now I just get code 67 or 11. I have done the following:
-Changed both fuel pumps, tank and frame rail pump (did one at a time, no improvement)
-Changed all fuel filters (in line filter, fuel reservoir filter and tank filter)
-Changed ignition module on distributer
-Changed both relays that control fuel pumps
-Cleaned battery terminals and body ground connections.
-New gas tank fill cap
I'm at a loss now as to what to do. I have been checking the codes with my multi-meter. I do not have a OBD1 diagnostic tool.
View 8 Replies
My Ranger has been a great truck but over the last 18 months ther has been a intermitent problem with the fuel system. It would run out of fuel ( foaming spray to nothing at the fuel rail ) and if you let it sit it would start and run after 8 hrs to a couple of days. Now it is all the time. The last time I let it sit for a week in a parking lot and it started, let it warm up and turned it off to move my other truck and it would not start when I returned. I have changed the fuel pump 3 times, 2 fuel filters, relay and pressure reg. on fuel rail.
View 5 Replies
I have a 1992 Ranger with 2.3L that suddenly lost power on freeway and stopped and couldn't restart. Towed it to Seattle, WA and need Ford Ranger 2.3L engine mechanic to double check the timing since new belt installed to make sure it was done right before cover and rest of engine reinstalled.
View 5 Replies
My friend's 1997 4 cyl ranger died and won't start. Cranks fine with no codes on OBD2. Was running fine before it died.
View 5 Replies
98 Mazda B4000 4.0 4x4
I bought this truck about two months ago and it has been great no problems starts right up and runs like a top. I was installing a 4 channel amp yesterday on and off and the dome light was on all day as the doors would periodically be opened or closed so it never did that cycle of 10 min or whatever when the lights turns off. This is what killed the battery.
I had my neighbor jump me and after a few minutes of charging it started right up and idled for about a minute long enough he left and parked, then it stalled. I started it about another 6 times before the battery died again. Every time it started fine then would idle between 1-10 sec then start to sputter and eventually die. Pressing the accelerator pedal only killed it faster.
I got a new battery today as the other charges so that I could fix it today without missing work again tomorrow. Unfortunately it does the same thing I was hoping that the voltage was just low or the polarity flipped or something on the other battery.
To sum it up the truck never gave previous symptoms just simply ran too low (battery never DIED the lights came on just clicked when starting) on power and now stalls when started which it does immediately no long cranking.
The twist; truck has an aftermarket alarm by Python. Problem is I don't know anything about the alarm or if it comes with an immobilizer. I am in the process of trying to figure this out but need to pull dash or something to find the "brain"? Never had an alarm like this I disconnected the clear square that adjusts the sensitivity hoping that was it but I don't know where or what I assume the brain of the alarm is.
View 14 Replies
So a couple days ago I started my truck and it fired up like normal, but then sputtered out and died after a few seconds. I tried starting it up again and it did the same thing. I tried once more and it started up fine and I drove away.
It sounds like my truck is running out of breath or something and just sputtering out. Runs fine once it turns over though. My issue is that it is happening almost every time I start it now. I have to turn it a couple times before it catches. What this might be?
View 11 Replies
I was driving my 85 2.3 liter down the road and it died all of a sudden like and wont start back up. I took out a plug to check for spark and had someone turn it over and I touched it to the big metal part the grill connects to at the top but I got nothing. It IS getting gas. The spark plug was white as if it was really hot and rough-looking for its relative newness. I bought a new distributor cap because it was corroded, but it didnt work. They tested the ignition module at the store and its good, so I am thinking distributor?? Also, could compression issues keep it from sparking? I am a little worried it got over-heated somehow, but don't know....
View 9 Replies
I have a 91 Ranger that the A/C was working great in but all of a sudden it stopped working even the fan. I turned it of and back on and it started again but then just stopped for good I can get the fan to work sometime, but no cold air. What it might be?
View 2 Replies
1995 Ford 4.0 ... All the following have been replaced on the truck.
High Pressure Fuel Pump and assembly
Idle Air Control Valve
Spark Plugs
Oxygen sensor (Bank 1 sensor 1 Oxygen)
Fuel Filter
The most recent item that I replaced is:
Coil Pack
Spark Plug Wires
Now, with the Coil Pack replacement, the truck drives good, as long as I do not floor it (After it heats up, about 15 minutes). Basically, if I try to pass someone, the truck acts as if it is chocking out, like it is not getting any fuel.
Before replacing the Coil Pack. It would chock out at any given time, rather just barely pressing the gas peddle, or just sitting idle.
I took it to a friends muffler shop, and he stated that it is not the exhaust that is causing the issue. I am at a loss. Is there anything else that I can check?
The truck seems to drive fine, as long as I do not get down on it, and try to take off fast after it heats up. When it is cold, I can take off like a bat out of hell, and it runs like no-ones business.
View 14 Replies
I have a 95 Ranger that when warmed up completely will buck when I let off of the gas. It is a 5 speed and this problem really only happens in 3rd gear and also have noticed it doesn't happen in 4WD. When the engine is cold and I am driving and let off the gas, the truck coasts smooth as silk and as it warms up, there becomes a louder thump when the gas is let off.
It will not do it all the time and it really only happens in third gear at low RPM's coming to a stop. I can give it gas and it picks right back up normally, so I doubt it is a misfire. Also since the truck is a 95 I do not have any CEL indicators, nor is there even a CEL light built into the dash in the truck. It isn't a huge issue because I am used to it and can drive it accordingly without having a problem.
View 13 Replies
I have a 95 Ranger with the 2.3L and it is a five speed. I am having a starting issue. I have replaced the ignition switch, clutch position switch, starter relay and had the starter tested. The truck will not start with the key. I can jump across the relay and it starts fine but will not even click with the key.
View 3 Replies
I am having an engine issue with my 1995 Ranger with a 2.3L. I have been having a P0340 code that kept appearing after several attempts at resetting the PCM. I gave up and took it to a Ford dealer for diagnostics and they called the CPS bad. They changed it, but the CEL light immediately came on with the code still kept coming up. The service rep. showed me the old sensor, it had a spot on the head of it where it looked like something was rubbing it. I'm assuming it's slightly rubbing on the gear it points to, which is the oil pump gear, correct? The truck runs fine, no performance issues whatsoever. Is it possible my oil pump shaft has developed play in it's shaft, causing this?
View 1 Replies
Had the top half of the intake off (2.3L) and fixed some vacuum leaks and replaced a power steering pump. Started truck and it ran funny like missing on one cylinder then cleared up then started making a loud knocking noise and running rough. Assumed that it swallowed something when I had the intake off and it got into a valve or into the cylinder. I pulled the plugs and there are no obvious signs of a problem. I also did a compression test and all 4 were around 150psi.
Put the plugs back in and started it and the same noise was there. Removed the serpent belt just in case it was power steering pump related and the noise was still there when I started the truck. Sounds like something is inside the engine still. Going to get a friends bore scope to check further. I guess I will split the manifold again and run the scope in there. Pending that I may also look down the plug holes with the scope. This is a major bummer. Not what I needed.
View 14 Replies
